Перейти к содержимому
Калькуляторы

sudo

Пользователи
  • Публикации

    126
  • Зарегистрирован

  • Посещение

О sudo

  • Звание
    Студент
    Студент

Посетители профиля

2200 просмотров профиля
  1. H801SCUH - 4 GE/10GE ports, Supporting automati c switching for remote software commissioning using GE upstream transmission. The H801X2CS board is a 2-port 10GE uplink interface card that provides two 10GE upstream or cascading optical ports. The H802X2CS board is a 2-port 10GE/GE uplink interface card that provides two 10GE/GE upstream or cascading optical ports. какие у вас цели?
  2. смотрите тут display io-packetfile information если нет драйвера для этой платы, то нужно накатить софт с драйвером для этой платы
  3. Ni hao! скачайте пожалуйста https://support.huawei.com/enterprise/en/software/259603953-ESW2000739725 dmitry.zhigachev gmail com
  4. Добрый день! можно получить эту прошивку? https://support.huawei.com/enterprise/en/software/262567250-ESW2001085755 dmitry.zhigachev gmail com
  5. да, такая команда, если 0/7/0 master port
  6. H801GICF это тоже гиговая плата. link-aggregation Function The link-aggregation command is used to create an Ethernet link aggregation group (LAG) and specify the master port in the group. Ethernet link aggregation means that two or more Ethernet ports of the same type are bound as a logical port. It improves link bandwidth without a hardware upgrade and effectively hardens link reliability using a link backup mechanism. The undo link-aggregation command is used to delete an Ethernet LAG. After the master port in an Ethernet LAG is deleted, the Ethernet LAG is deleted and the protection and load sharing among ports in the Ethernet LAG are also canceled. NOTE: When adding a port to or deleting a port from a link aggregation group, if this port is already connected to the peer device, run the shutdown command for the port or remove the optical fiber to avoid a link loop. Format link-aggregation frameid/slotid port-list [ frameid/slotid port-list ] mode [ workmode lacp-static ] undo link-aggregation { frameid/slotid/portid | all } конфиг не теряется при конфигурировании агрегации.
  7. плохо искали, гуглите по link-aggregation в SCU порты только 1гиг, а какая у вас gui мы не знаем, display board 0 покажите
  8. 0 или 47 или вообще 127 это идентификатор онт на порту ontid<U><0,127> ONT ID От ID никак не зависит, будет работать онт или нет. У вас, я так думаю какая то проблема с лайн-профилем, или dba. может много ресурсов выделяется для остальных онт.
  9. (config)#interface gpon 0/X (config-if-gpon-0/X)#display port traffic X
  10. Две команды вам в помощь OLT(config-if-gpon-0/1)#display ont info 1 all OLT#display service-port next-free-index
  11. так на порту не может быть больше 128 онт... OLT(config-if-gpon-0/1)#ont add 1 ? --------------------------------------------- Command of gpon-0/1 Mode: --------------------------------------------- loid-auth Logic ONU identifier authentication mode ontid<U><0,127> ONT ID то есть у вас нумерация должна быть такая 0/1/0/0-127 0/1/1/0-127 и так далее можете вообще не указывать id ont. олт сама подставит свободный id и в выхлопе покажет какой выдался
  12. какую ошибку олт в лог выдает при добавлении новой онт?
  13. dba-profile ограничивает только upstream. создавайте traffic table ip и вешайте его на service-port. должно сработать