Tirrr Posted July 8, 2016 Здравствуйте! Пытался решить проблему на форуме UBNT и openwrt. Пока нет результата. Суть проблемы в том, что UniFi AP работала под AirOS 5.5 или 5.5.2, точно не помню. Потом начались какие то проблемы и её просто заменили на другую. Сейчас я добрался до этой UniFi AP и заменил флеш память на всякий случай. И вот что интересно. Я прошивал её на разные версии родных прошивок. Также на AirOS 5.5 и 5.5.2 с которыми она раньше работала. И не работает. Максимум, что я от неё добился, так это пинга на 192.168.1.20 на прошивке 5.5 AirOS и пинга на адрес выданный по DHCP на родной прошивке. Контроллер не видит точку. WEB в случае AirOS не доступен. При попытке зайти на неё по SSH или WinSCP после ввода пароля ничего не происходит. SSH просто висит, а WinSCP закрывает окно. Логи терминала при разных прошивках немного разные, но примерно вот такие кёрнел паник. Нашёл в сети информацию, что при такой проблеме оперативная память может глючить. Но вот есть у меня сомнения, я прошил DDWRT и она прекрасно пускает в WEB интерфейс. Но она платная и в триал режиме находится и вообще она не нужна. На точке нужна openwrt. На двух других UniFi AP всё нормально встало. Прошивать пробовал и как методом прошивки и методом копирования образов разделов и вообще всей флеш памяти. Мне просто очень интересно в чём проблема си ей точки. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Tirrr Posted July 8, 2016 (edited) Вот лог загрузки на DDWRT. Тоже со всякими ошибками, но может так и надо, триал ведь. U-Boot 1.1.4-gb387d959 (Dec 8 2011 - 10:16:49) Board: Ubiquiti Networks AR7241 board (e502-41746.0101.002e) DRAM: 64 MB Flash: 8 MB Net: eth0, eth1 Hit any key to stop autoboot: 0 ## Booting image at 9f050000 ... Image Name: MIPS Linux Kernel Image Created: 2013-03-25 5:33:06 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 957742 Bytes = 935.3 kB Load Address: 80002000 Entry Point: 80224220 Verifying Checksum at 0x9f050040 ...OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] flash_size passed from bootloader = 8 [ 0.000000] bootconsole [early0] enabled AR7241 detect mem size Uart Init Booting AR7240(Python)... [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, lin esize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Linux version 3.5.7 (root@dd-wrt) (gcc version 4.7.3 20121205 (pr erelease) (Linaro GCC 4.7-2012.12) ) #6131 Mon Mar 25 05:50:53 CET 2013 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=sq uashfs noinitrd init=/sbin/init [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61848k/65536k available (2217k kernel code, 3688k reserve d, 422k data, 168k init, 0k highmem) [ 0.000000] NR_IRQS:80 [ 0.000000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] NET: Registered protocol family 16 [ 0.110000] found calibration data for slot 0 on 0xBF7F1000 [ 0.320000] registering PCI controller with io_map_base unset [ 0.340000] bio: create slab <bio-0> at 0 [ 0.340000] PCI host bridge to bus 0000:00 [ 0.350000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.350000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.360000] pci 0000:00:00.0: fixup device configuration [ 0.360000] bootstrap returns device 168C:2E [ 0.370000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bi t] [ 0.370000] PCI: mapping irq 72 to pin1@0000:00:00.0 [ 0.380000] Switching to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.390000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.400000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.400000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.410000] TCP: reno registered [ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.430000] NET: Registered protocol family 1 [ 0.430000] gpio_proc: module loaded and /proc/gpio/ created [ 0.440000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created [ 0.450000] squashfs: version 3.0 (2006/03/15) Phillip Lougher [ 0.450000] msgmni has been set to 120 [ 0.460000] io scheduler noop registered [ 0.460000] io scheduler deadline registered (default) [ 0.470000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.490000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.500000] console [ttyS0] enabled, bootconsole disabled [ 0.500000] console [ttyS0] enabled, bootconsole disabled [ 0.510000] guessed flashsize = 8M [ 0.520000] scanning for root partition [ 0.520000] uboot detected [ 0.520000] guessed bootloader size = 50000 [ 0.530000] [ 0.530000] found squashfs at 150000 [ 0.540000] Creating 8 MTD partitions on "ar7240-nor0": [ 0.540000] 0x000000000000-0x000000050000 : "RedBoot" [ 0.550000] 0x000000050000-0x0000007e0000 : "linux" [ 0.550000] 0x000000150000-0x0000006c0000 : "rootfs" [ 0.560000] mtd: partition "rootfs" set to be root filesystem [ 0.570000] 0x0000006c0000-0x0000007e0000 : "ddwrt" [ 0.570000] 0x0000007e0000-0x0000007f0000 : "nvram" [ 0.580000] 0x0000007f0000-0x000000800000 : "board_config" [ 0.590000] 0x000000000000-0x000000800000 : "fullflash" [ 0.590000] 0x000000000000-0x000000050000 : "fullboot" [ 0.600000] tun: Universal TUN/TAP device driver, 1.6 [ 0.610000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.010000] PPP generic driver version 2.4.2 [ 1.020000] PPP BSD Compression module registered [ 1.020000] PPP Deflate Compression module registered [ 1.030000] PPP MPPE Compression module registered [ 1.030000] NET: Registered protocol family 24 [ 1.060000] u32 classifier [ 1.060000] Performance counters on [ 1.060000] input device check on [ 1.070000] Actions configured [ 1.070000] Netfilter messages via NETLINK v0.30. [ 1.070000] nf_conntrack version 0.5.0 (966 buckets, 3864 max) [ 1.080000] nf_conntrack_rtsp v0.6.21 loading [ 1.090000] nf_nat_rtsp v0.6.21 loading [ 1.090000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.090000] IPP2P v0.8.2 loading [ 1.100000] TCP: westwood registered [ 1.100000] TCP: hybla registered [ 1.110000] TCP: vegas registered [ 1.110000] NET: Registered protocol family 17 [ 1.110000] Bridge firewalling registered [ 1.120000] 8021q: 802.1Q VLAN Support v1.8 [ 1.120000] searching for nvram [ 1.130000] nvram size = 0 [ 1.160000] Atheros AR71xx hardware watchdog driver version 0.1.0 [ 1.160000] ar71xx-wdt: timeout=15 secs (max=22) ref freq=195000000 [ 1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 1.180000] Freeing unused kernel memory: 168k freed start service starting Architecture code for unifi starting hotplug Jan 1 00:00:02 udevtrigger[243]: parse_config_file: can't open '/etc/udev/udev. conf' as config file: No such file or directory start MSTP Daemon 1970-01-01 00:00:03 main: Sanity checks succeeded done load ATH Ethernet Driver [ 4.040000] ag71xx_mdio: probed [ 4.040000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 4.600000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid= 004dd041, driver=Generic PHY] [ 4.610000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII [ 5.160000] eth1: Found an AR7240/AR9330 built-in switch configure eth0 to 04:18:d6:a8:7f:25 configure eth1 to 04:18:d6:a8:7f:25 load ATH 802.11 a/b/g Driver load ATH9K 802.11n Driver [ 8.560000] Compat-drivers backport release: compat-drivers-2013-01-21-1 [ 8.570000] Backport based on wireless-testing.git master-2013-02-22 [ 8.580000] compat.git: wireless-testing.git [ 8.770000] cfg80211: Calling CRDA to update world regulatory domain [ 8.780000] cfg80211: World regulatory domain updated: [ 8.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp) [ 8.790000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 8.800000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 20 00 mBm) [ 8.800000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20 00 mBm) [ 8.810000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 8.820000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 9.520000] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb0000000, irq=72 [ 9.530000] cfg80211: Calling CRDA for country: US [ 9.540000] cfg80211: Regulatory domain changed to country: US [ 9.540000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp) [ 9.550000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 27 00 mBm) [ 9.560000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 17 00 mBm) [ 9.560000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 9.570000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 9.580000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm) [ 9.590000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 30 00 mBm) [ 9.600000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 40 00 mBm) [ 9.600000] eth0: link up (100Mbps/Full duplex) [ 9.750000] SQUASHFS error: lzma returned unexpected result 0x1 [ 9.760000] SQUASHFS error: Unable to read fragment cache block [414d9b] [ 9.770000] SQUASHFS error: Unable to read page, block 414d9b, size 8551 [ 9.770000] SQUASHFS error: lzma returned unexpected result 0x1 [ 9.780000] SQUASHFS error: Unable to read fragment cache block [414d9b] [ 9.790000] SQUASHFS error: Unable to read page, block 414d9b, size 8551 [ 9.790000] SQUASHFS error: lzma returned unexpected result 0x1 [ 9.800000] SQUASHFS error: Unable to read fragment cache block [414d9b] [ 9.810000] SQUASHFS error: Unable to read page, block 414d9b, size 8551 [ 9.810000] SQUASHFS error: lzma returned unexpected result 0x1 [ 9.820000] SQUASHFS error: Unable to read fragment cache block [414d9b] [ 9.830000] SQUASHFS error: Unable to read page, block 414d9b, size 8551 iw: applet not found [ 11.570000] nf_conntrack: automatic helper assignment is deprecated and it wi ll be removed soon. Use the iptables CT target to attach helpers instead. ath9k deconfigure_single: phy0 ath0 iw: applet not found CTL_set_cist_bridge_config: Got return code 0, -1 Couldn't find bridge with ind[ 11.800000] eth0: link down ex 5 Couldn't change bridge bridge_forward_delay [ 11.850000] device eth0 entered promiscuous mode ath9k deconfigure_single: phy0 ath0 iw: applet not found /bin/sh: iw: Permission denied /bin/sh: iw: Permission denied [ 12.610000] eth0: link up (100Mbps/Full duplex) [ 12.610000] br0: port 1(eth0) entered forwarding state [ 12.620000] br0: port 1(eth0) entered forwarding state ath9k configure_single: phy0 ath0 /bin/sh: iw: Permission denied /bin/sh: iw: Permission denied /bin/sh: iw: Permission denied 549:ath0 call mac80211autochannel for interface: ath0 mac80211autochannel PHY not found setup ath0 77:D2:15:CC:7F:89 /bin/sh: iw: Permission denied br0: No such process [ 18.230000] SQUASHFS error: lzma returned unexpected result 0x1 [ 18.230000] SQUASHFS error: Unable to read fragment cache block [40be73] [ 18.240000] SQUASHFS error: Unable to read page, block 40be73, size 8f28 [ 18.280000] SQUASHFS error: lzma returned unexpected result 0x1 [ 18.280000] SQUASHFS error: Unable to read fragment cache block [40be73] [ 18.290000] SQUASHFS error: Unable to read page, block 40be73, size 8f28 [ 18.320000] SQUASHFS error: lzma returned unexpected result 0x1 [ 18.330000] SQUASHFS error: Unable to read fragment cache block [40be73] [ 18.340000] SQUASHFS error: Unable to read page, block 40be73, size 8f28 [ 18.370000] SQUASHFS error: lzma returned unexpected result 0x1 [ 18.380000] SQUASHFS error: Unable to read fragment cache block [40be73] [ 18.390000] SQUASHFS error: Unable to read page, block 40be73, size 8f28 SIOCGIFFLAGS: No such device iptables-restore: applet not found SIOCGIFFLAGS: No such device iptables: applet not found connect: Network is unreachable connect: Network is unreachable connect: Network is unreachable gethostbyname: Network is unreachable iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables-restore: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables-restore: applet not found SIOCGIFFLAGS: No such device iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables: applet not found iptables-restore: applet not found ath9k radio 1: phy0 ath0 [ 27.640000] br0: port 1(eth0) entered forwarding state connect: Network is unreachable connect: Network is unreachable connect: Network is unreachable gethostbyname: Network is unreachable connect: Network is unreachable connect: Network is unreachable connect: Network is unreachable gethostbyname: Network is unreachable connect: Network is unreachable connect: Network is unreachable connect: Network is unreachable gethostbyname: Network is unreachable connect: Network is unreachable connect: Network is unreachable connect: Network is unreachable gethostbyname: Network is unreachable Вот openwrt U-Boot 1.1.4-gb387d959 (Dec 8 2011 - 10:16:49) Board: Ubiquiti Networks AR7241 board (e502-41746.0101.002e) DRAM: 64 MB Flash: 8 MB Net: eth0, eth1 Hit any key to stop autoboot: 0 ## Booting image at 9f050000 ... Image Name: MIPS OpenWrt Linux-3.18.20 Created: 2015-09-11 16:08:52 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1098502 Bytes = 1 MB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum at 0x9f050040 ...OK Uncompressing Kernel Image ... OK Starting kernel ... [ 0.000000] Linux version 3.18.20 (buildbot@builder1) (gcc version 4.8.3 (Ope nWrt/Linaro GCC 4.8-2014.04 r46450) ) #1 Fri Sep 4 21:55:57 CEST 2015 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR7241 rev 1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256 [ 0.000000] Kernel command line: board=UBNT-UF console=ttyS0,115200 mtdparts =spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM) ro rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61004K/65536K available (2621K kernel code, 129K rwdata, 344K rodata, 224K init, 194K bss, 4532K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Clocks: CPU:390.000MHz, DDR:390.000MHz, AHB:195.000MHz, Ref:5.000 MHz [ 0.000000] Calibrating delay loop... 259.27 BogoMIPS (lpj=1296384) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.080000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090000] NET: Registered protocol family 16 [ 0.090000] MIPS: machine is Ubiquiti UniFi [ 0.320000] registering PCI controller with io_map_base unset [ 0.330000] PCI host bridge to bus 0000:00 [ 0.340000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.340000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.350000] pci_bus 0000:00: No busn resource found for root bus, will use [b us 00-ff] [ 0.350000] pci 0000:00:00.0: fixup device configuration [ 0.360000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bi t] [ 0.360000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.370000] Switched to clocksource MIPS [ 0.370000] NET: Registered protocol family 2 [ 0.380000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.380000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.400000] TCP: reno registered [ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.400000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.410000] NET: Registered protocol family 1 [ 0.420000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.430000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.440000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc. [ 0.450000] msgmni has been set to 119 [ 0.450000] io scheduler noop registered [ 0.460000] io scheduler deadline registered (default) [ 0.460000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.470000] console [ttyS0] disabled [ 0.500000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 121 87500) is a 16550A [ 0.510000] console [ttyS0] enabled [ 0.510000] console [ttyS0] enabled [ 0.510000] bootconsole [early0] disabled [ 0.510000] bootconsole [early0] disabled [ 0.520000] m25p80 spi0.0: found s25fl064k, expected m25p80 [ 0.530000] m25p80 spi0.0: s25fl064k (8192 Kbytes) [ 0.530000] 5 cmdlinepart partitions found on MTD device spi0.0 [ 0.540000] Creating 5 MTD partitions on "spi0.0": [ 0.540000] 0x000000000000-0x000000040000 : "u-boot" [ 0.550000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.560000] 0x000000050000-0x0000007b0000 : "firmware" [ 0.580000] 2 uimage-fw partitions found on MTD device firmware [ 0.590000] 0x000000050000-0x00000015c346 : "kernel" [ 0.590000] 0x00000015c346-0x0000007b0000 : "rootfs" [ 0.600000] mtd: device 4 (rootfs) set to be root filesystem [ 0.600000] 1 squashfs-split partitions found on MTD device rootfs [ 0.610000] 0x000000390000-0x0000007b0000 : "rootfs_data" [ 0.620000] 0x0000007b0000-0x0000007f0000 : "cfg" [ 0.620000] 0x0000007f0000-0x000000800000 : "EEPROM" [ 0.660000] libphy: ag71xx_mdio: probed [ 1.250000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd0 41, driver=Generic PHY] [ 1.260000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII [ 1.260000] TCP: cubic registered [ 1.270000] NET: Registered protocol family 17 [ 1.270000] bridge: automatic filtering via arp/ip/ip6tables has been depreca ted. Update your scripts to load br_netfilter if you need this. [ 1.280000] Bridge firewalling registered [ 1.290000] 8021q: 802.1Q VLAN Support v1.8 [ 1.300000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 1.310000] Freeing unused kernel memory: 224K (80368000 - 803a0000) [ 2.510000] SQUASHFS error: xz decompression failed, data probably corrupt [ 2.520000] SQUASHFS error: squashfs_read_data failed to read block 0x1782ba [ 2.530000] SQUASHFS error: Unable to read fragment cache entry [1782ba] [ 2.530000] SQUASHFS error: Unable to read page, block 1782ba, size 13db0 [ 2.540000] SQUASHFS error: Unable to read fragment cache entry [1782ba] [ 2.550000] SQUASHFS error: Unable to read page, block 1782ba, size 13db0 [ 2.560000] SQUASHFS error: Unable to read fragment cache entry [1782ba] [ 2.560000] SQUASHFS error: Unable to read page, block 1782ba, size 13db0 [ 2.570000] SQUASHFS error: Unable to read fragment cache entry [1782ba] [ 2.580000] SQUASHFS error: Unable to read page, block 1782ba, size 13db0 [ 2.580000] SQUASHFS error: Unable to read fragment cache entry [1782ba] [ 2.590000] SQUASHFS error: Unable to read page, block 1782ba, size 13db0 /sbin/init: '/usr/lib/libjson-c.so.2' is not an ELF file /sbin/init: can't load library 'libjson-c.so.2' [ 2.630000] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00 001000 [ 2.630000] [ 2.630000] ---[ end Kernel panic - not syncing: Attempted to kill init! exit code=0x00001000 [ 2.630000] [ 82.370000] random: nonblocking pool is initialized Edited July 8, 2016 by Tirrr Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Tirrr Posted July 9, 2016 Ну вот, кажется зря всех потревожил на форумах. Новая флеш оказалась с битыми ячейками. Китайцы *ать их. Неделю времени потратил. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Yuraner Posted July 12, 2016 Всё существенно хуже у Вас. Надо было для начала поспрашать поисковики, покопать ссылки и тогда Вы узнали бы, что прошивка и вся система защиты от контрафакта юбикьюти привязана к секьюрити ареа чипов флеши. Дальше сами. Удачи! Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Engineer09 Posted July 12, 2016 Получается, в случае выхода из строя флешки, ремонт невозможен! Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Yuraner Posted July 12, 2016 Ну-у, по большому счёту да, хотя может кто уже и поломал, ещё и от даты выпуска зависит. А вообще, у них самый распространённый ремонт это перепрограммирование флеши и всё. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Tirrr Posted July 24, 2016 (edited) Получается, в случае выхода из строя флешки, ремонт невозможен! Ремонт то возможен в случае выхода из строя флешки, но придётся сидеть на openwrt в случае unifi. А в случае остального на прошивке 5.5. Всё существенно хуже у Вас. Надо было для начала поспрашать поисковики, покопать ссылки и тогда Вы узнали бы, что прошивка и вся система защиты от контрафакта юбикьюти привязана к секьюрити ареа чипов флеши. Дальше сами. Удачи! Это я уже понял. Мне для unifi и openwrt хватит. Кстати, сказывается это на качестве работы устройства или нет, это вопрос, ответ на который хотелось бы знать. Ну и борьба с counterfeit всё таки нужна. А то скоро настанет время, что запихать старую прошивку в новую ubnt будет невозможно. А брак у ubnt есть, особенно во флешках. Интересно как родная прошивка узнаёт дату изготовления устройства. Это можно было бы использовать, чтобы дать знать прошивке, что устройство выпущено до 2012 и прошивка в свою очередь не должна проверять на counterfeit. У меня до сих пор работает старый airgridM5 с прошивкой 5.6.3 и там не пишется, что это genuine product. Edited July 24, 2016 by Tirrr Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
Yuraner Posted July 25, 2016 Ну и борьба с counterfeit всё таки нужна Почитайте лан23, там несколько раз поднималась эта тема. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
