fzakharov Posted October 31, 2016 (edited) Коммутация WIC-1T и WIC-2T кабелями DB60-V35MT + переходник V35-RS232 + SS-RS232FC выполнена. , порты включаются, лампочки горят, но На Wic-1T interface Serial1/0 ip address 10.0.0.2 255.255.255.0 encapsulation ppp Serial1/0 is up, line protocol is down Hardware is DSCC4 Serial Internet address is 10.0.0.2/24 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, loopback not set Keepalive set (10 sec) LCP Listen Closed: IPCP, CDPCP Last input never, output 00:02:51, output hang never Last clearing of "show interface" counters 00:03:56 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 11 packets output, 154 bytes, 0 underruns 0 output errors, 0 collisions, 4 interface resets 0 output buffer failures, 0 output buffers swapped out 29 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up На Wic-2T задан clock rate 2000000 interface Serial0/1 ip address 10.0.0.1 255.255.255.0 encapsulation ppp clockrate 2000000 dce-terminal-timing-enable Serial0/1 is up, line protocol is down Hardware is PowerQUICC Serial Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation PPP, LCP REQsent, loopback not set Keepalive set (10 sec) Last input never, output 00:00:00, output hang never Last clearing of "show interface" counters 00:04:15 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1158 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 52 packets output, 728 bytes, 0 underruns 0 output errors, 0 collisions, 16 interface resets 0 output buffer failures, 0 output buffers swapped out 10 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Edited October 31, 2016 by fzakharov Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
DRiVen Posted October 31, 2016 И сколько все это длиной? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted October 31, 2016 Метров 5 - кишка такая составная Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
DRiVen Posted October 31, 2016 Метров 5 - кишка такая составная На максимально возможную скорость для WIC-2T и длины интерфейсных кабелей обратите внимание, а так же на строку в вашем же выводе "Available Bandwidth 1158 kilobits/sec". А вы ему рэйт на 2мбит ввалили. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted October 31, 2016 Спасибо. Сlock rate 64000 - работает, но только если связка DB60-RS232MT + SS-RS232FC. Кстати, расстояние тоже около 5 метров. Снижение clock rate при связке кабелями DB60-V35MT + переходник V35-RS232 + SS-RS232FC результата не дает. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted October 31, 2016 Если использовать 1-й кабель вместо второго, то все работает. Второй - составной, может в нем дело? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
DRiVen Posted October 31, 2016 Если не работает даже на 64000, то скорее всего так и есть, возможно что-то с распиновкой или на разъемах с контактами плохо. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted November 1, 2016 Ну может тогда появились бы ошибки тут: Router#sh contr s0/0 Interface Serial0/0 Hardware is PowerQUICC MPC860 DTE V.35 TX and RX clocks detected. idb at 0x82E4B9C0, driver data structure at 0x82E53ABC SCC Registers: General [GSMR]=0x2:0x00000030, Protocol-specific [PSMR]=0x8 Events [sCCE]=0x0000, Mask [sCCM]=0x001F, Status [sCCS]=0x06 Transmit on Demand [TODR]=0x0, Data Sync [DSR]=0x7E7E Interrupt Registers: Config [CICR]=0x00367F80, Pending [CIPR]=0x00008000 Mask [CIMR]=0x40204000, In-srv [CISR]=0x00000000 Command register [CR]=0x600 Port A [PADIR]=0x0000, [PAPAR]=0xFFFF [PAODR]=0x0000, [PADAT]=0xF6FF Port B [PBDIR]=0x0180F, [PBPAR]=0x0000E [PBODR]=0x00000, [PBDAT]=0x3E77D Port C [PCDIR]=0x00C, [PCPAR]=0x000 [PCSO]=0x020, [PCDAT]=0xFC2, [PCINT]=0x00F Receive Ring rmd(680126B0): status 9000 length 1A address 7D3B2E4 rmd(680126B8): status 9000 length 60C address 7D3AC64 rmd(680126C0): status 9000 length 60C address 7D3FA64 rmd(680126C8): status 9000 length 60C address 7D3A5E4 или тут: Router#sh int s0 Serial0/0 is up, line protocol is up Hardware is PowerQUICC Serial Internet address is 10.0.0.2/24 MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec, reliability 254/255, txload 1/255, rxload 1/255 Encapsulation HDLC, loopback not set Keepalive set (10 sec) Last input 00:00:09, output 00:00:01, output hang never Last clearing of "show interface" counters 00:17:55 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 91 packets input, 4526 bytes, 0 no buffer Received 91 broadcasts, 0 runts, 0 giants, 0 throttles 22 input errors, 0 CRC, 22 frame, 0 overrun, 0 ignored, 0 abort 187 packets output, 28808 bytes, 0 underruns 0 output errors, 0 collisions, 46 interface resets 0 output buffer failures, 0 output buffers swapped out 66 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
DRiVen Posted November 1, 2016 Ну может тогда появились бы ошибки тут Их разве нет? 91 packets input, 4526 bytes, 0 no buffer Received 91 broadcasts, 0 runts, 0 giants, 0 throttles 22 input errors, 0 CRC, 22 frame, 0 overrun, 0 ignored, 0 abort P.S>А зачем вам этот копролит понадобился вообще? Лабу что ли делаете? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted November 1, 2016 Хотел собрать лабу на стареньком оборудовании, а не на виртуалках, но кабели SS-SS и SS-DB60 дороговаты, вот нашел такие, соединил и ошибки... Может их можно "вручную укоротить"?? Если проблема только в длине кабелей. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
NikAlexAn Posted November 1, 2016 Спасибо. Сlock rate 64000 - работает, но только если связка DB60-RS232MT + SS-RS232FC. Кстати, расстояние тоже около 5 метров. Снижение clock rate при связке кабелями DB60-V35MT + переходник V35-RS232 + SS-RS232FC результата не дает. Если в первой связке работает то зачем вторую мучить? А вторая связка вообще допустима? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted November 1, 2016 Спасибо за комментарий. Ну почему же не допустима моя длинная связка?? Кабели есть, собираются, DTE/DCE на WIC определяются. Да и 6м. - нормальное расстояние. Ну поставлю BW поменьше: мне для icmp/cdp пакетов не страшно. Чего-то мелкого не хватает, чтобы схемка заработала. Кстати в async режиме "is up, line protocol is up", но пинги не идут ((. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted November 1, 2016 Оказывается белые переходники не EIA-232, а EIA-530, соответственно связаться с SS-232 они никак не могут. ((( Как вы думаете, друзья, какие варианты могут тут быть?? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
NikAlexAn Posted November 2, 2016 С кисковскими последовательными интерфейсами не сталкивался а вот на Vanguard-ах DB-25 и я их тупо сам спаял по схемкам в мануалах. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
fzakharov Posted November 2, 2016 Как думаете, а если достать кабель DB60-RS530 и заменить ему папу на маму согласно мануалам - все свяжется?? Я посмотрел, там вроде внутри проводочки одни, без микросхем. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...