smart85 Posted March 13, 2014 Коллеги, приветствую. Проблема с EX4200-24T, девайс новый, из коробки. Включаем, идет бут: U-Boot 1.1.6 (Feb 6 2008 - 11:27:42) Board: EX4200-24T 2.17 EPLD: Version 6.0 (0x85) DRAM: Initializing (1024 MB) FLASH: 8 MB USB: scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found Consoles: U-Boot console Found compatible API, ver. 7 FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.1 (marcelm@apg-bbuild01.juniper.net, Wed Feb 6 11:23:55 PST 2008) Memory: 1024MB Loading /boot/defaults/loader.conf /kernel data=0x7fcbac+0x8774c syms=[0x4+0x6ee90+0x4+0x9bae3] Hit [Enter] to boot immediately, or space bar for command prompt. Booting [/kernel]... Kernel entry at 0xa00000e0 ... GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb platform_early_bootinit: EX Series Early Boot Initialization Copyright © 1996-2010, Juniper Networks, Inc. All rights reserved. Copyright © 1992-2006 The FreeBSD Project. Copyright © 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. JUNOS 10.0S10.1 #0: 2010-11-08 21:23:50 UTC builder@ormonth.juniper.net:/volume/build/junos/10.0/service/10.0S10.1/obj-powerpc/bsd/sys/compile/JUNIPER-EX Timecounter "decrementer" frequency 50000000 Hz quality 0 cpu0: Freescale e500v2 core revision 2.2 cpu0: HID0 80004080<EMCP,TBEN,EN_MAS7_UPDATE> real memory = 1050673152 (1002 MB) avail memory = 1029038080 (981 MB) ETHERNET SOCKET BRIDGE initialising Initializing EXSERIES platform properties ... nexus0: <PPC e500 Nexus device> ocpbus0: <on-chip peripheral bus> on nexus0 openpic0: <OpenPIC in on-chip peripheral bus> iomem 0xfef40000-0xfef600b3 on ocpbus0 uart0: <16550 or compatible> iomem 0xfef04500-0xfef0450f irq 58 on ocpbus0 uart0: console (9600,n,8,1) uart1: <16550 or compatible> iomem 0xfef04600-0xfef0460f irq 58 on ocpbus0 lbc0: <Freescale 8533 Local Bus Controller> iomem 0xfef05000-0xfef05fff,0xff000000-0xffffffff irq 22 on ocpbus0 cfi0: <AMD/Fujitsu - 8MB> iomem 0xff800000-0xffffffff on lbc0 syspld0 iomem 0xff000000-0xff00ffff on lbc0 tsec0: <eTSEC ethernet controller> iomem 0xfef24000-0xfef24fff irq 45,46,50 on ocpbus0 tsec0: hardware MAC address b0:c6:9a:63:72:7f miibus0: <MII bus> on tsec0 e1000phy0: <Marvell 88E1112 Gigabit PHY> on miibus0 e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto pcib0: <Freescale MPC8544 PCI host controller> iomem 0xfef08000-0xfef08fff,0xf0000000-0xf3ffffff on ocpbus0 pci0: <PCI bus> on pcib0 pci0: <serial bus, USB> at device 18.0 (no driver attached) ehci0: <Philips ISP156x USB 2.0 controller> mem 0xf0001000-0xf00010ff irq 22 at device 18.2 on pci0 usb0: EHCI version 1.0 usb0: <Philips ISP156x USB 2.0 controller> on ehci0 usb0: USB revision 2.0 uhub0: Philips EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered umass0: STMicroelectronics ST72682 High Speed Mode, rev 2.00/2.10, addr 2 pcib1: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0a000-0xfef0afff,0xe0000000-0xe3ffffff,0xec000000-0xec0fffff irq 42 on ocpbus0 pci1: <PCI bus> on pcib1 pcib2: <PCI-PCI bridge> at device 0.0 on pci1 pci2: <PCI bus> on pcib2 mpfe0: <Juniper EX-series Packet Forwarding Engine> mem 0xa4000000-0xa40fffff,0xa0000000-0xa3ffffff irq 19 at device 0.0 on pci2 pcib3: <Freescale MPC8544 PCI Express host controller> iomem 0xfef0b000-0xfef0bfff,0xe8000000-0xebffffff,0xec200000-0xec2fffff irq 43 on ocpbus0 pci3: <PCI bus> on pcib3 pcib4: <PCI-PCI bridge> at device 0.0 on pci3 pci4: <PCI bus> on pcib4 mpfe1: <Juniper EX-series Packet Forwarding Engine> mem 0xb4000000-0xb40fffff,0xb0000000-0xb3ffffff irq 18 at device 0.0 on pci4 i2c0: <MPC85XX OnChip i2c controller> iomem 0xfef03000-0xfef03014 irq 59 on ocpbus0 i2c1: <MPC85XX OnChip i2c controller> iomem 0xfef03100-0xfef03114 irq 59 on ocpbus0 idma0: <mp85xxx DMA Controller> iomem 0xfef21000-0xfef21300 irq 36 on ocpbus0 Initializing product: 41 .. bme0:Virtual BME driver initializing Timecounters tick every 1.000 msec Loading the NETPFE picpeer module IPsec: Initialized Security Association Processing. da0 at umass-sim0 bus 0 target 0 lun 0 da0: <ST ST72682 2.10> Removable Direct Access SCSI-2 device da0: 40.000MB/s transfers da0: 1000MB (2048000 512 byte sectors: 64H 32S/T 1000C) if_pfe_open: listener socket opened, listening on ... Trying to mount root from ufs:/dev/da0s1a Attaching /packages/jbase via /dev/mdctl... Mounted jbase package on /dev/md0... Verified manifest signed by PackageProduction_10_0_0 Verified jboot signed by PackageProduction_10_0_0 Verified jbase-10.0S10.1 signed by PackageProduction_10_0_0 /packages/jcrypto-ex-10.0S10.1 not present. /packages/jdocs-ex-10.0S10.1 not present. Mounted jkernel-ex package on /dev/md1... Verified manifest signed by PackageProduction_10_0_0 Verified jkernel-ex-10.0S10.1 signed by PackageProduction_10_0_0 /packages/jpfe-ex42x-10.0S10.1 not present. Mounted jroute-ex package on /dev/md2... Verified manifest signed by PackageProduction_10_0_0 Verified jroute-ex-10.0S10.1 signed by PackageProduction_10_0_0 /packages/jswitch-ex-10.0S10.1 not present. Mounted jweb-ex package on /dev/md3... Verified manifest signed by PackageProduction_10_0_0 Verified jweb-ex-10.0S10.1 signed by PackageProduction_10_0_0 Executing /packages/mnt/jweb-ex-10.0S10.1/mount.post.. Automatic reboot in progress... FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 51449 free (33 frags, 6427 blocks, 0.0% fragmentation) FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 28282 free (50 frags, 3529 blocks, 0.2% fragmentation) FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 61059 free (219 frags, 7605 blocks, 0.3% fragmentation) FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 160780 free (20 frags, 20095 blocks, 0.0% fragmentation) FILE SYSTEM CLEAN; SKIPPING CHECKS clean, 160780 free (20 frags, 20095 blocks, 0.0% fragmentation) Creating initial configuration...mgd: error: Couldn't open lib "/usr/lib/dd//libjcrypto-dd.so": Cannot open "/usr/lib/dd//libjcrypto-dd.so" mgd: error: Couldn't open lib "/usr/lib/dd//libjcrypto_junos-dd.so": Cannot open "/usr/lib/dd//libjcrypto_junos-dd.so" mgd: error: Couldn't open lib "/usr/lib/dd//libjdocs-dd.so": Cannot open "/usr/lib/dd//libjdocs-dd.so" mgd: error: Couldn't open lib "/opt/lib/dd/libjswitch-dd.so": Cannot open "/opt/lib/dd/libjswitch-dd.so" mgd: error: Couldn't open lib "/opt/lib/dd/libautod-dd.so": Cannot open "/opt/lib/dd/libautod-dd.so" mgd: commit complete Setting initial options: debugger_on_panic=NO debugger_on_break=NO. Starting optional daemons: . Doing initial network setup: . Initial interface configuration: additional daemons:. Additional routing options:kern.module_path: /boot//kernel;/bootLoading the NETPFE ethernet module /modules -> /booLoading the EX-series platform NETPFE module t//kernel;/boot/modules;/modules grat_arp_on_ifup=YES: net.link.ether.inet.grat_arp_on_ifup: 1 -> 1 grat_arp_delay=${grat_arp_delay}: net.link.ether.inet.grat_arp_delay: 0 -> 0 kld netpfe drv: ifpfed_ethkld platform: ex_ifpfe if_vcpkern.module_path: /boot//kernel;/boot/modules;/modules -> /boot//kernel;/boot/modules;/modules;/modules/peertype kld peertype: peertype_hcm peertype_pfem peertype_sfi peertype_slavere. Doing additional network setup:. Starting final network daemons:. setting ldconfig path: /usr/lib /opt/lib starting standard daemons: cron. Local package initialization:. kern.securelevel: -1 -> 1 starting local daemons:. Sat Apr 16 16:10:35 UTC 2011 Amnesiac (ttyu0) В итоге, часть CLI недоступна (по сравнению с EX4200-24F), на LCD дисплее пишет: Loading junos (хотя в консоль пускает), на кнопки не реагирует. Что это может быть? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
pfexec Posted March 13, 2014 (edited) Что это может быть?сделайте реинсталл 11.4R10 (или 12.3R5, если очень хочется) с форматом.Verified jbase-10.0S10.1 signed by PackageProduction_10_0_010.0S10 :D вам такой анахронизм не нужен в любом случае, а апгрейдить его "мягко" устанеш. Edited March 13, 2014 by pfexec Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
smart85 Posted March 13, 2014 Что это может быть?сделайте реинсталл 11.4R10 (или 12.3R5, если очень хочется) с форматом.Verified jbase-10.0S10.1 signed by PackageProduction_10_0_010.0S10 :D вам такой анахронизм не нужен в любом случае, а апгрейдить его "мягко" устанеш. Коллега, а как нам быть в случае того, что поддержка на девайсы не куплена, где брать софт? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
pfexec Posted March 13, 2014 (edited) Коллега, а как нам быть в случае того, что поддержка на девайсы не куплена, где брать софт?идите на support.juniper.net и регайтесь.после этого сможете спокойно скачать junos желанной версии. :) Edited March 13, 2014 by pfexec Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
smart85 Posted March 13, 2014 (edited) После входа в систему вот что имеем: --- JUNOS 10.0S10.1 built 2010-11-08 21:23:50 UTC root@:LC:0% cli rend_dlinit: not a proper library: /usr/lib/render//libkmd-render.so: Cannot open "/usr/lib/render//libkmd-render.so" rend_dlinit: not a proper library: /usr/lib/render//liblldpd-render.so: Cannot open "/usr/lib/render//liblldpd-render.so" rend_dlinit: not a proper library: /usr/lib/render//libeswd-render.so: Cannot open "/usr/lib/render//libeswd-render.so" rend_dlinit: not a proper library: /usr/lib/render//libdot1xd-render.so: Cannot open "/usr/lib/render//libdot1xd-render.so" rend_dlinit: not a proper library: /usr/lib/render//libautod-render.so: Cannot open "/usr/lib/render//libautod-render.so" rend_dlinit: not a proper library: /usr/lib/render//libsflowd-render.so: Cannot open "/usr/lib/render//libsflowd-render.so" rend_dlinit: not a proper library: /usr/lib/render//libvccpd-render.so: Cannot open "/usr/lib/render//libvccpd-render.so" {linecard:0} root> show version {linecard:0} root> show version detail {linecard:0} root> configure Entering configuration mode {linecard:0}[edit] root# set ? Possible completions: > access Network access configuration > access-profile Access profile for this instance > accounting-options Accounting data configuration + apply-groups Groups from which to inherit configuration data > chassis Chassis configuration > class-of-service Class-of-service configuration > diameter Diameter protocol layer > event-options Event processing configuration > firewall Define a firewall configuration > forwarding-options Configure options to control packet forwarding > groups Configuration groups > interfaces Interface configuration > jsrc JSRC partition configuration > jsrc-partition JSRC partition configuration > logical-systems Logical systems > multicast-snooping-options Multicast snooping option configuration > policy-options Routing policy option configuration > protocols Routing protocol configuration > routing-instances Routing instance configuration > routing-options Protocol-independent routing option configuration > security Security configuration > services > snmp Simple Network Management Protocol configuration > system System parameters {linecard:0}[edit] root# run show configuration ## Last commit: 2011-04-16 15:43:14 UTC by root version 10.0S10.1; system { root-authentication { encrypted-password "$1$OReVqebR$65Wt8HmVbB4.e40mJwfYH1"; ## SECRET-DATA } syslog { user * { any emergency; } file messages { any notice; authorization info; } file interactive-commands { interactive-commands any; } } } chassis { container-devices { device-count 1; } } interfaces { ge-0/0/0 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/1 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/2 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/3 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/4 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/5 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/6 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/7 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/8 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/9 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/10 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/11 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/12 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/13 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/14 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/15 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/16 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/17 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/18 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/19 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/20 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/21 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/22 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/0/23 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/1/0 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } xe-0/1/0 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/1/1 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } xe-0/1/1 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/1/2 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } ge-0/1/3 { unit 0 { ## ## Warning: statement ignored: unsupported platform (ex4200-24t) ## family ethernet-switching; } } } protocols { igmp-snooping { ## ## invalid path element 'vlans' ## vlan all; } } {linecard:0}[edit] root# Почему оно считает себя linecard а не RE ? Почему про интерфейсы так пишет и почему их больше ge-0/1/0 - ge-0/1/3 ? Edited March 13, 2014 by mse.rus77 Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
pfexec Posted March 13, 2014 Почему оно считает себя linecard а не RE ? Почему про интерфейсы так пишет и почему их больше в два раза?я думаю самое время для фразы: "позовите одмина, он вам поможет." Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
pfexec Posted March 13, 2014 http://kb.juniper.net/InfoCenter/index?page=content&id=KB20643 - читаем как поставить с форматом http://rutracker.org/forum/viewtopic.php?t=4045147 - качаем софт Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
MonaxGT Posted March 13, 2014 Почему оно считает себя linecard а не RE ? Почему про интерфейсы так пишет и почему их больше ge-0/1/0 - ge-0/1/3 ? А как вы инициализировали кластер? загрузкой или с предустановками? Поменяйте софт, как рекомендовал pfexec. Я собирал на 12.3 (вроде), все работало прекрасно. По поводу невидимых интерфейсов, то просто создайте их используя аналогичные порты. Например порт ge-0/0/1, то порты бэкапа будут ge-1/0/1 - вроде бы, могу ошибаться, собирал один раз. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
smart85 Posted March 14, 2014 Почему оно считает себя linecard а не RE ? Почему про интерфейсы так пишет и почему их больше ge-0/1/0 - ge-0/1/3 ? А как вы инициализировали кластер? загрузкой или с предустановками? Поменяйте софт, как рекомендовал pfexec. Я собирал на 12.3 (вроде), все работало прекрасно. По поводу невидимых интерфейсов, то просто создайте их используя аналогичные порты. Например порт ge-0/0/1, то порты бэкапа будут ge-1/0/1 - вроде бы, могу ошибаться, собирал один раз. Устройство не в стэке, но такое ощущение, что когда-то оно в нем было в роли бэкапа. Хотя странно, мы еще этот девайс не эксплуатировали. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
smart85 Posted March 14, 2014 http://kb.juniper.net/InfoCenter/index?page=content&id=KB20643 - читаем как поставить с форматом http://rutracker.org/forum/viewtopic.php?t=4045147 - качаем софт Большое спасибо, все получилось. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...