QWE Posted July 11, 2018 (edited) Один DAC кабель вынул, другой вставил (на другом конце при этом ничего не было) и порт заморгал оранжевым цветом. Тафик естественно не ходит. Оборудование включенное в faulty port линка не видит. Статус порта в консоли. #show interfaces tenGigabitEthernet 1/50 TenGigabitEthernet1/50 is down, line protocol is down (faulty) Hardware is Ten Gigabit Ethernet Port, address is 7081.0564.4db1 (bia 7081.0564.4db1) MTU 1546 bytes, BW 10000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, Auto-speed, link type is auto, media type is No Gbic input flow-control is off, output flow-control is off ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 357777932142 packets input, 335216940488232 bytes, 0 no buffer Received 18351075 broadcasts (2224927 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 16023 overrun, 0 ignored 0 input packets with dribble condition detected 6911767432 packets output, 2748490516762 bytes, 0 underruns 0 output errors, 0 collisions, 5 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out #show interfaces tenGigabitEthernet 1/50 status Port Name Status Vlan Duplex Speed Type Te1/50 #DDD# faulty 1 full auto No Gbic #show interfaces tenGigabitEthernet 1/50 status err-disabled Port Name Status Reason Err-disabled Vlans Te1/50 ##DDD## faulty none Вернул прежний DAC кабель - без результата. как лечить? Ребут или порт сдох и менять свич? Edited July 12, 2018 by QWE Share this post Link to post Share on other sites More sharing options...
QWE Posted July 11, 2018 (edited) Если сейчас повтыкать в порт DAC кабель то Cisco шлет сообщения (SNMP trap) в систему мониторинга "Facility.Serverity: 22.5 at Jul 11 18:54:16 on host: 10.10.1.29 Jul 11 19:00:20 MSK: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=50: Transceiver has been inserted" "Facility.Serverity: 22.5 at Jul 11 18:54:32 on host: 10.10.1.29 Jul 11 19:00:36 MSK: %C4K_IOSINTF-5-TRANSCEIVERREMOVED: Slot=1 Port=50: Transceiver has been removed" "Facility.Serverity: 22.5 at Jul 11 18:55:34 on host: 10.10.1.29 Jul 11 19:01:38 MSK: %C4K_IOSINTF-5-TRANSCEIVERINSERTED: Slot=1 Port=50: Transceiver has been inserted" Вернули старый кабель в порт и по SNMP циско отдает серийник DAC кабеля в систему мониторинга Zabbix "Решено: TenGigabitEthernet1/50: Device has been replaced (new serial number received)" Edited July 11, 2018 by QWE Share this post Link to post Share on other sites More sharing options...
ShyLion Posted July 12, 2018 errdisable recovery interval цифра Share this post Link to post Share on other sites More sharing options...
QWE Posted July 12, 2018 7 минут назад, ShyLion сказал: errdisable recovery interval цифра делал, но помогало Share this post Link to post Share on other sites More sharing options...
zhenya` Posted July 12, 2018 shut / no shut ? Share this post Link to post Share on other sites More sharing options...
QWE Posted July 12, 2018 1 час назад, zhenya` сказал: shut / no shut ? тоже пробовал Share this post Link to post Share on other sites More sharing options...
