kadaj2102 Опубликовано 19 июля, 2012 (изменено) · Жалоба есть Cisco c1760 c E1 интерфейсом. по Е1 к ней подключен банк каналов Asteroid. Соответственно в настройках таймслоты получаются FXS-портами. проблема в том, что не работает определитель номера у клиентов. Помогите кто чем может, пробовали крутить cptone, alerting, и attenuation на порту, не помогло. куски конфига циски: controller E1 1/0 ds0-group 1 timeslots 1 type fxs-loop-start ds0-group 2 timeslots 2 type fxs-loop-start ds0-group 3 timeslots 3 type fxs-loop-start ds0-group 4 timeslots 4 type fxs-loop-start ds0-group 5 timeslots 5 type fxs-loop-start ds0-group 6 timeslots 6 type fxs-loop-start ds0-group 7 timeslots 7 type fxs-loop-start ds0-group 8 timeslots 8 type fxs-loop-start ds0-group 9 timeslots 9 type fxs-loop-start ds0-group 10 timeslots 10 type fxs-loop-start ds0-group 11 timeslots 11 type fxs-loop-start ds0-group 12 timeslots 12 type fxs-loop-start ds0-group 13 timeslots 13 type fxs-loop-start ds0-group 14 timeslots 14 type fxs-loop-start ds0-group 15 timeslots 15 type fxs-loop-start ds0-group 16 timeslots 17 type fxs-loop-start ds0-group 17 timeslots 18 type fxs-loop-start ds0-group 18 timeslots 19 type fxs-loop-start ds0-group 19 timeslots 20 type fxs-loop-start ds0-group 20 timeslots 21 type fxs-loop-start ds0-group 21 timeslots 22 type fxs-loop-start ds0-group 22 timeslots 23 type fxs-loop-start ds0-group 23 timeslots 24 type fxs-loop-start ds0-group 24 timeslots 25 type fxs-loop-start ds0-group 25 timeslots 26 type fxs-loop-start ds0-group 26 timeslots 27 type fxs-loop-start ds0-group 27 timeslots 28 type fxs-loop-start ds0-group 28 timeslots 29 type fxs-loop-start ds0-group 29 timeslots 30 type fxs-loop-start ds0-group 30 timeslots 31 type fxs-loop-start voice-port 1/0:11 no battery-reversal output attenuation 0 cptone RU description Erohin station-id number 7хххххххххх (номер в е.164) caller-id enable dial-peer voice xxxxxx pots destination-pattern 7xxxxxxxxxx port 1/0:11 dial-peer voice 1000 voip answer-address T destination-pattern .T voice-class codec 2 session target ras dtmf-relay h245-alphanumeric fax rate 14400 fax nsf 000000 fax protocol t38 ls-redundancy 5 hs-redundancy 2 fallback none а также : sh voice port Foreign Exchange Station Slot is 1, Sub-unit is 0, Port is 11 Type of VoicePort is FXS Operation State is DORMANT Administrative State is UP The Last Interface Down Failure Cause is Administrative Shutdown Description is Erohin Noise Regeneration is enabled Non Linear Processing is enabled Non Linear Mute is disabled Non Linear Threshold is -21 dB Music On Hold Threshold is Set to -38 dBm In Gain is Set to 0 dB Out Attenuation is Set to 0 dB Echo Cancellation is enabled Echo Cancellation NLP mute is disabled Echo Cancellation NLP threshold is -21 dB Echo Cancel Coverage is set to 64 ms Echo Cancel worst case ERL is set to 6 dB Playout-delay Mode is set to adaptive Playout-delay Nominal is set to 60 ms Playout-delay Maximum is set to 200 ms Playout-delay Minimum mode is set to default, value 40 ms Playout-delay Fax is set to 300 ms Connection Mode is normal Connection Number is not set Initial Time Out is set to 10 s Interdigit Time Out is set to 10 s Call Disconnect Time Out is set to 60 s Supervisory Disconnect Time Out is set to 750 ms Ringing Time Out is set to 180 s Wait Release Time Out is set to 30 s Companding Type is A-law Rx A bit no conditioning set Rx B bit no conditioning set Rx C bit no conditioning set Rx D bit no conditioning set Tx A bit no conditioning set Tx B bit no conditioning set Tx C bit no conditioning set Tx D bit no conditioning set Region Tone is set for RU Analog Info Follows: Currently processing none Maintenance Mode Set to None (not in mtc mode) Number of signaling protocol errors are 0 Station name None, Station number 7xxxxxxxxxx Caller ID Info Follows: Standard BELLCORE Output attenuation is set to 14 dB Caller ID is transmitted after 1 ring(s) Translation profile (Incoming): Translation profile (Outgoing): Voice card specific Info Follows: Signal Type is loopStart Ring Frequency is 25 Hz Hook Status is On Hook Ring Active Status is inactive Ring Ground Status is inactive Tip Ground Status is inactive Digit Duration Timing is set to 100 ms InterDigit Duration Timing is set to 100 ms Hookflash-in Timing is set to 1000 ms Hookflash-out Timing is set to 400 ms No disconnect acknowledge Ring Cadence is defined by CPTone Selection Ring Cadence are [8 32] * 100 msec Ringer Equivalence Number is set to 1 sh dial-peer voice peer type = voice, information type = voice, description = `', tag = 711018, destination-pattern = `74872711018', answer-address = `', preference=0, CLID Restriction = None CLID Network Number = `' CLID Second Number sent CLID Override RDNIS = disabled, source carrier-id = `', target carrier-id = `', source trunk-group-label = `', target trunk-group-label = `', numbering Type = `unknown' group = 711018, Admin state is up, Operation state is up, Outbound state is up, incoming called-number = `', connections/maximum = 17/unlimited, DTMF Relay = disabled, huntstop = disabled, in bound application associated: 'DEFAULT' out bound application associated: '' dnis-map = permission :both incoming COR list:maximum capability outgoing COR list:minimum requirement Translation profile (Incoming): Translation profile (Outgoing): incoming call blocking: translation-profile = `' disconnect-cause = `no-service' advertise 0x40 capacity_update_timer 25 addrFamily 0 oldAddrFamily 0 type = pots, prefix = `', forward-digits default session-target = `', voice-port = `1/0:11', direct-inward-dial = disabled, digit_strip = enabled, register E.164 number with GK = TRUE fax rate = system, payload size = 20 bytes supported-language = '' Time elapsed since last clearing of voice call statistics never Connect Time = 1140576, Charged Units = 0, Successful Calls = 68, Failed Calls = 17, Incomplete Calls = 0 Accepted Calls = 124, Refused Calls = 0, Last Disconnect Cause is "10 ", Last Disconnect Text is "normal call clearing (16)", Last Setup Time = 43071790. и дебаг vpn signal: Jul 18 05:30:59.766: htsp_process_event: [0/0:1(1), FXSLS_OFFHOOK, E_HTSP_PROCEEDING] Jul 18 05:31:08.480: htsp_process_event: [0/0:15(15), FXSLS_WAIT_OFFHOOK, E_HTSP_RELEASE_REQ]fxsls_waitoff_release[Foreign Exchange Station0/0:15(15)] set signal state = 0x4htsp_setup_req Jul 18 05:31:11.289: htsp_process_event: [1/0:8(8), FXSLS_ONHOOK, E_HTSP_SETUP_REQ]fxsls_onhook_setup[Foreign Exchange Station1/0:8(8)] set signal state = 0x0ht sp_alert[Foreign Exchange Station1/0:8(8)] set signal state = 0x0 Jul 18 05:31:11.297: [1/0:8(8)] htsp_set_caller_id_tx calling num=74xxxxxxxxxx display_info= called num=7xxxxxxxxxx Jul 18 05:31:11.297: [1/0:8(8)] Caller ID String 44 37 34 38 37 32 37 31 30 30 30 30 43 Jul 18 05:31:11.297: [1/0:8(8)] htsp_set_caller_id_tx_time Caller ID:FSK_DURING_RING Jul 18 05:31:11.297: [1/0:8(8)] htsp_start_caller_id_tx string length=13 Jul 18 05:31:11.313: htsp_process_event: [1/0:8(8), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxsls_waitoff_voice Jul 18 05:31:11.409: htsp_process_event: [1/0:8(8), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxsls_waitoff_voice Jul 18 05:31:11.433: htsp_process_event: [1/0:8(8), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxsls_waitoff_voice Jul 18 05:31:11.433: htsp_process_event: [1/0:8(8), FXSLS_WAIT_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH]fxsls_waitoff_voice Jul 18 05:31:12.086: htsp_process_event: [0/0:1(1), FXSLS_OFFHOOK, E_DSP_SIG_0100]fxsls_offhook_onhook, HF duration=1000 Jul 18 05:31:12.086: htsp_timer - 1000 msec Jul 18 05:31:13.088: htsp_process_event: [0/0:1(1), FXSLS_OFFHOOK, E_HTSP_EVENT_TIMER]fxsls_offhook_timer Jul 18 05:31:13.088: htsp_process_event: [0/0:1(1), FXSLS_ONHOOK, E_HTSP_RELEASE_REQ]fxsls_onhook_release Jul 18 05:31:13.088: htsp_timer_stop Jul 18 05:31:14.478: htsp_process_event: [0/0:5(5), FXSLS_ONHOOK, E_DSP_SIG_1100]fxsls_onhook_offhook htsp_setup_ind Jul 18 05:31:14.482: [0/0:5(5)] get_local_station_id calling num=74872711118 calling name= calling time=07/18 09:31 Jul 18 05:31:14.494: htsp_process_event: [0/0:5(5), FXSLS_WAIT_SETUP_ACK, E_HTSP_SETUP_ACK]fxsls_check_auto_call Jul 18 05:31:16.105: htsp_digit_ready(0/0:5(5)): digit = 2 Jul 18 05:31:16.417: htsp_digit_ready(0/0:5(5)): digit = 5 Jul 18 05:31:16.886: htsp_digit_ready(0/0:5(5)): digit = 0 Jul 18 05:31:17.996: htsp_process_event: [1/0:8(8), FXSLS_WAIT_OFFHOOK, E_DSP_SIG_1100]fxsls_waitoff_offhook[Foreign Exchange Station1/0:8(8)] set signal state = 0x4[Foreign Exchange Station1/0:8(8)] set signal state = 0x6 Jul 18 05:31:17.996: [1/0:8(8)] htsp_stop_caller_id_tx htsp_dial Jul 18 05:31:17.996: htsp_process_event: [1/0:8(8), FXSLS_CONNECT, E_DSP_DIALING_DONE] Jul 18 05:31:18.793: htsp_digit_ready(0/0:5(5)): digit = 6 Jul 18 05:31:19.246: htsp_digit_ready(0/0:5(5)): digit = 4 Jul 18 05:31:19.546: htsp_digit_ready(0/0:5(5)): digit = 5 Jul 18 05:31:29.547: htsp_process_event: [0/0:5(5), FXSLS_OFFHOOK, E_HTSP_PROCEEDING]htsp_alert_notify Jul 18 05:31:30.168: htsp_process_event: [0/0:5(5), FXSLS_OFFHOOK, E_HTSP_VOICE_CUT_THROUGH] Jul 18 05:31:37.748: htsp_process_event: [0/0:5(5), FXSLS_OFFHOOK, E_HTSP_CONNECT]fxsls_offhook_connect[Foreign Exchange Station0/0:5(5)] set signal state = 0x6 Изменено 24 июля, 2012 пользователем kadaj2102 Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
Fanatik Опубликовано 19 июля, 2012 · Жалоба при входяших нет аона? Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
kadaj2102 Опубликовано 20 июля, 2012 · Жалоба Да, точнее не совсем АОН'а а caller-id (немного другое, но суть таже - позволяет определять номер вызывающего) Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
evil-man Опубликовано 31 августа, 2012 · Жалоба И не будет работать. Сигнализация cas loop-start не предусматривает передачу номера вызывающего абонента. Пруфлинк тут - Understanding How Digital T1 CAS (Robbed Bit Signaling) Works in IOS Gateways. Единственный вариант - попробовать другой тип сигнализации, например, e&m, но не факт, что заработает. Пинайте производителя железки на счёт поддержки другого типа сигнализации. Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
kadaj2102 Опубликовано 3 сентября, 2012 · Жалоба Спасибо большое "злой человек" )) теперь хоть знаем где копать а не пальцем в жопу) Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...