Juniper MX-80

[Users]

Не грузится. Подозрение на то, что вышли из строя  флешки. Ставил их на матеренку  тоже не определятюся. Как определить что 100% проблема в них ?
 

U-Boot 1.1.6 (Feb  3 2010 - 11:57:02)

CPU:   8572, Version: 2.1, (0x80e00021)
Core0:  E500, Version: 3.0, (0x80210030)
Clock Configuration:
       CPU0:1333 MHz,        CPU1:1333 MHz, CCB: 533 MHz,
       DDR: 267 MHz (533 MT/s data rate) (Synchronous), LBC:  33 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: MX80 1.9
CPLD:  Version 0x1d
DRAM:  Initializing  -     DDR: 2048 MB
Testing DRAM from 0x00000000 to 0x80000000
DRAM test phase 1:
DRAM test phase 2:
DRAM test passed.
Now running in RAM - U-Boot at: 0ffa0000
Enable CPLD Watchdog
POST: U-boot memory location PASSED

Scaning PCIE bus:

Scanning PCI Express` Bus .. for bus 0
    Found(0.0.0), (0x1957,0x41) Class(0xb20) :MPC8572 PCIE Controller
    BAR0 = 0xc0000000

Scanning PCI Express` Bus .. for bus 1
    Found(1.0.0), (0x10b5,0x8112) Class(0x604) :PEX8112 PCIe-to-PCI Bridge
    BAR0 = 0xc0100000    BAR1 = 0x0

Scanning PCI Express` Bus .. for bus 2
    Found(2.1.0), (0x1033,0x35) Class(0xc03) :uPD720101/2 USB(OHCI) Controller
    BAR0 = 0xc0200000
    Found(2.1.1), (0x1033,0xe0) Class(0xc03) :uPD720101/2 USB(EHCI) Controller
    BAR0 = 0xc0201000
 ----------- PCIE scan complete, last bus = 2 ------------

FLASH:  8 MB
L2 cache 1MB: enabled
In:    serial
Out:   serial
Err:   serial
USB:   scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
Net:   fxp0: PHY is Marvell 88E1112S (1410c97)
me0, em0, fxp0 [PRIME], em1

ELF file is 32 bit
Loading .text @ 0x00010080 (176156 bytes)
Loading .rodata @ 0x0003b09c (14008 bytes)
Loading .rodata.str1.4 @ 0x0003e754 (15716 bytes)
Loading set_Xcommand_set @ 0x000424b8 (88 bytes)
Loading .rodata.cst4 @ 0x00042510 (12 bytes)
Loading .data @ 0x00043000 (13896 bytes)
Loading .sdata @ 0x00046648 (80 bytes)
Clearing .sbss @ 0x00046698 (264 bytes)
Clearing .bss @ 0x000467a0 (9232 bytes)
## Starting application at 0x00010080 ...
Consoles: U-Boot console
Will try to boot from
USB
nand-flash0
nand-flash1

FreeBSD/PowerPC U-Boot bootstrap loader, Revision 2.2
(vaidyasd@svl-junos-pool69.juniper.net, Wed Feb  3 09:50:07 PST 2010)
Memory: 2048MB

can't load '/kernel'
can't load '/kernel.old'

Type '?' for a list of commands, 'help' for more detailed help.
loader>

Edited October 26, 2023 by Users

[hwall]

Поставить другие 

[Users]

:)пока их нет