maniackiller Опубликовано 13 октября, 2009 · Жалоба Случилась вот такая неприятность. На циске перестал работать ethernet port. Но! На самом порту циски и порту коммутатора, к которой подключена циска, горят индикаторы и Link/Act. При втыкании/вытыкании пачкорда из порта, на консоли не вылазиют трапы о UP/DOWN интерфесе. Делать на интерфейсе sh/no sh не помогает. Перезагрузка по питанию тоже. Вот что на ней: *Mar 1 06:02:02: %SYS-5-RELOAD: Reload requested by condor on console. Reload Reason: Reload command.Xmodem file system is available. flashfs[0]: 147 files, 7 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 7741440 flashfs[0]: Bytes used: 5406208 flashfs[0]: Bytes available: 2335232 flashfs[0]: flashfs fsck took 17 seconds. Base ethernet MAC Address: 00:1d:45:b3:8c:d8 Initializing ethernet port 0... Reset ethernet port 0... Reset done! link auto-negotiating.... auto-negotiation takes 10000 milli-seconds to complete ERROR: timeout waiting for auto-negotiation to complete ERROR: fail to bring ethernet link up The system has been encountered an error initializing ethernet port. You may need to check hardware The system is ignoring the error and continuing boot. If you interrupt the system boot process, the following commands will reinitialize ethernet, tftp, and finish loading the operating system software: ether_init tftp_init boot Loading "flash:/c1310-k9w7-mx.124-3g.JA1/c1310-k9w7-mx.124-3g.JA1"...######################################################################### ################################################################################# ################################################################################# ################################################################################# ################################################################################# ################################################### File "flash:/c1310-k9w7-mx.124-3g.JA1/c1310-k9w7-mx.124-3g.JA1" uncompressed and installed, entry point: 0x3000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C1310 Software (C1310-K9W7-M), Version 12.4(3g)JA1, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Thu 19-Jul-07 23:32 by kellythw Image text-base: 0x00003000, data-base: 0x008313C0 Initializing flashfs... flashfs[1]: 147 files, 7 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 7741440 flashfs[1]: Bytes used: 5406208 flashfs[1]: Bytes available: 2335232 flashfs[1]: flashfs fsck took 2 seconds. flashfs[1]: Initialization complete....done Initializing flashfs. Radio 1 A506 5500 E8000000 A0000000 80000000 3 This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. cisco AIR-BR1310G-A-K9-R (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory. Processor board ID FTX1138U028 PowerPCElvis CPU at 262Mhz, revision number 0x0950 Last reset from reload 1 FastEthernet interface 1 802.11 Radio(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:1D:45:B3:8C:D8 Part Number : 73-8960-09 PCA Assembly Number : 800-24963-06 PCA Revision Number : A0 PCB Serial Number : FOC11334BT7 Top Assembly Part Number : 800-28763-01 Top Assembly Serial Number : FTX1138U028 Top Revision Number : A0 Product/Model Number : AIR-BR1310G-A-K9-R Press RETURN to get started! Пытался прерывать загрузку и делать так: bridge: ether_init Initializing ethernet port 0... Reset ethernet port 0... Reset done! link auto-negotiating.... auto-negotiation takes 10000 milli-seconds to complete ERROR: timeout waiting for auto-negotiation to complete ERROR: fail to bring ethernet link up Не помогает. sh int fastEthernet 0 FastEthernet0 is up, line protocol is down Hardware is PowerPCElvis Ethernet, address is 001d.45b3.8cd8 (bia 001d.45b3.8cd8) MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Auto-duplex, Auto Speed, MII ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/1127/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out sh controllers fa0 PowerPCElvis Ethernet unit 0 PHY Hardware is Broadcom BCM5914 rev. 2 (id_register: 0x40, 0x6322) rx_intr: 0 tx_intr: 0 mac_err_isr: 0 phy_link_isr:0 Current station address 001d.45b3.8cd8, default address 001d.45b3.8cd8 MAL register dump: malcr 0x0007C082 0x180 malesr 0x00000000 0x181 malier 0x0000000F 0x182 maltxcasr 0x80000000 0x184 maltxcarr 0x80000000 0x185 maltxeobisr 0x00000000 0x186 maltxdeir 0x00000000 0x187 malrxcasr 0x80000000 0x190 malrxcarr 0x80000000 0x191 malrxeobisr 0x00000000 0x192 malrxdeir 0x00000000 0x193 maltxctp0r 0x01C6AEA0 0x1A0 malrxctp0r 0x01C6ADA0 0x1C0 malrcbs0 0x00000060 0x1E0 EMAC register dump: emacmr0 0x18000000 0x00 emacmr1 0xA1788000 0x04 emactmr0 0x00000000 0x08 emactmr1 0x380F0000 0x0C emacrmr 0x7D180000 0x10 emacisr 0x00000002 0x14 emacier 0x00000001 0x18 emaciah 0x0000001D 0x1C emacial 0x45B38CD8 0x20 emacptr 0x0000FFFF 0x2C emaclsah 0x00000000 0x50 emaclsal 0x00000000 0x54 emacipgr 0x00000004 0x58 emacstacr 0x78098001 0x5C emactrtr 0x18000000 0x60 emacrwmr 0x0F002000 0x64 emacoctx 0x00000000 0x68 emacocrx 0x00000000 0x6C UIC register dump: uicsr 0x00009FB4 0xC0 uicer 0x803F0048 0xC2 uicmsr 0x00000000 0xC6 PHY register dump: 1000 7809 0040 6322 01E1 0000 0004 2001 0000 0000 0000 0000 0000 0000 0000 0000 1000 0001 0000 0000 0200 0600 0100 0000 0028 3002 4400 008A 0028 0000 0010 RX ring with 16 entries at 0x1C6ADA0, Buffer size 1524 Rxhead = 0x1C6ADA0 (0), Rxp = 0xD3AAF0 (0) 00 pak=0x0F24518 buf=0x1983AC8 status=8400 pak_size=0 01 pak=0x0F24894 buf=0x198455C status=8400 pak_size=0 02 pak=0x0F24C10 buf=0x1984FF0 status=8400 pak_size=0 03 pak=0x0F24F8C buf=0x1985A84 status=8400 pak_size=0 04 pak=0x0F25308 buf=0x1986518 status=8400 pak_size=0 05 pak=0x0F25684 buf=0x1986FAC status=8400 pak_size=0 06 pak=0x0F25A00 buf=0x1987A40 status=8400 pak_size=0 07 pak=0x0F25D7C buf=0x19884D4 status=8400 pak_size=0 08 pak=0x0F260F8 buf=0x1988F68 status=8400 pak_size=0 09 pak=0x0F26474 buf=0x19899FC status=8400 pak_size=0 10 pak=0x0F267F0 buf=0x198A490 status=8400 pak_size=0 11 pak=0x0F3F2E0 buf=0x198AF24 status=8400 pak_size=0 12 pak=0x0F3F65C buf=0x198B9B8 status=8400 pak_size=0 13 pak=0x0F3F9D8 buf=0x198C44C status=8400 pak_size=0 14 pak=0x0F3FD54 buf=0x198CEE0 status=8400 pak_size=0 15 pak=0x0F400D0 buf=0x198D974 status=C400 pak_size=0 TX ring with 8 entries at 0x1C6AEA0, tx_count = 0 tx_head = 0x1C6AEA0 (0), head_txp = 0xD3AB4C (0) tx_tail = 0x1C6AEA0 (0), tail_txp = 0xD3AB4C (0) 00 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 01 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 02 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 03 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 04 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 05 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 06 pak=0x0000000 buf=0x0000000 status=1700 pak_size=0 07 pak=0x0000000 buf=0x0000000 status=5700 pak_size=0 0 missed datagrams, 0 overruns 0 transmitter underruns, 0 excessive collisions 0 single collisions, 0 multiple collisions 0 dma memory errors, 0 CRC errors 0 alignment errors, 0 runts, 0 giants emac/mal specific errors: 0 rx in range, 0 rx out range 0 mal_rx_serr, 0 mal_tx_serr 0 mal_rx_de, 0 mal_tx_de 0 emac_int 0 mal_err_isr 0 SQE errors, 0 tx CRC errors 0 output queue fail Как можно железку реанимировать? Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
MaXToP Опубликовано 13 октября, 2009 · Жалоба паяльником и заменой чипа Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
maniackiller Опубликовано 13 октября, 2009 · Жалоба паяльником и заменой чипа А можно подробнее? Что менять, как? Может кто-то ремонтирует и сколько стоит такой ремонт? Заранее спасибо Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...