seelent Posted December 8, 2014 Добрый день. Имеем связку коммутаторов, подключенных в следующей последовательности: DGS-3120 -- Cisco SG300-20 -- DGS-3200. Пытаемся поднять на них mstp. DGS -3120(Рут): sh stp DGS-3120-24TC:admin#sh stp Command: show stp STP Bridge Global Settings --------------------------- STP Status : Enabled STP Version : MSTP Max Age : 20 Forward Delay : 15 Max Hops : 20 TX Hold Count : 6 Forwarding BPDU : Disabled New Root Trap : Enabled Topology Change Trap : Enabled NNI BPDU Address : dot1d Sh stp instance: STP Instance Settings --------------------------- Instance Type : CIST Instance Status : Enabled Instance Priority : 8192 (Bridge Priority : 8192 , SYS ID Ext : 0 ) STP Instance Operational Status -------------------------------- Designated Root Bridge : 8192 /9C-D6-43-1E-B6-80 External Root Cost : 0 Regional Root Bridge : 8192 /9C-D6-43-1E-B6-80 Internal Root Cost : 0 Designated Bridge : 8192 /9C-D6-43-1E-B6-80 Root Port : None Max Age : 20 Forward Delay : 15 Last Topology Change : 752 Topology Changes Count : 117 STP Instance Settings --------------------------- Instance Type : MSTI(2) Instance Status : Enabled Instance Priority : 8194 (Bridge Priority : 8192 , SYS ID Ext : 2 ) STP Instance Operational Status -------------------------------- Regional Root Bridge : 8194 /9C-D6-43-1E-B6-80 Internal Root Cost : 0 Designated Bridge : 8194 /9C-D6-43-1E-B6-80 Root Port : None Remaining Hops : 20 Last Topology Change : 16391 Topology Changes Count : 13 STP Instance Settings --------------------------- Instance Type : MSTI(2) Instance Status : Enabled Instance Priority : 8194 (Bridge Priority : 8192 , SYS ID Ext : 2 ) STP Instance Operational Status -------------------------------- Regional Root Bridge : 8194 /9C-D6-43-1E-B6-80 Internal Root Cost : 0 Designated Bridge : 8194 /9C-D6-43-1E-B6-80 Root Port : None Remaining Hops : 20 Last Topology Change : 16427 Topology Changes Count : 13 show stp mst_config_id Current MST Configuration Identification ---------------------------------------- Configuration Name : Mosk Revision Level :0 MSTI ID Vid list ------- ------------------------------------------------------------- CIST - 1 37,154,938,999,3040-3049 2 1-36,38-153,155-937,939-998,1000-3039,3050-4094 Ну, то есть, есть регион Mosk, и два mst инстанса с вланами внутри. 3120 задуман как временный рут, поэтому приоритет 8192. Идем на циску: #sh spanning-tree mst-configuration Gathering information .......... Current MST configuration Name: Mosk Revision: 0 Instance Vlans Mapped State -------- ------------------------------------------------ ----- 1 37,154,938,999,3040-3049 enabled 2 1-36,38-153,155-937,939-998,1000-3039,3050-4094 enabled Соответственно: #show spanning-tree instance 1 Gathering information .......... ###### MST 1 Vlans Mapped: 154,938,3040-3049 Root ID Priority 8192 Address 9c:d6:43:1e:b6:80 Path Cost 20000 Root Port gi19 Rem hops 19 Bridge ID Priority 32768 Address c0:7b:bc:13:ca:86 #sh spanning-tree instance 2 Gathering information .......... ###### MST 2 Vlans Mapped: 1,42 Root ID Priority 8192 Address 9c:d6:43:1e:b6:80 Path Cost 20000 Root Port gi19 Rem hops 19 Bridge ID Priority 32768 Address c0:7b:bc:13:ca:86 Т.о. рут определился правильно. И так, к слову сказать, на всех коммутаторах, кроме 3200(другие коммутаторы в другом плече). Но дело доходит до 3200: DGS-3200-10:4#sh stp Command: show stp STP Bridge Global Settings --------------------------- STP Status : Enabled STP Version : MSTP Max Age : 20 Forward Delay : 15 Max Hops : 20 TX Hold Count : 6 Forwarding BPDU : Enabled New Root Trap : Enabled Topology Change Trap : Enabled DGS-3200-10:4#show stp mst_config_id Command: show stp mst_config_id Current MST Configuration Identification ---------------------------------------- Configuration Name : Mosk Revision Level :0 MSTI ID Vid list ------- ------------------------------------------------------------- CIST - 1 37,154,938,999,3040-3049 2 1-36,38-153,155-937,939-998,1000-3039,3050-4094 DGS-3200-10:4#show stp instance 1 Command: show stp instance 1 STP Instance Settings --------------------------- Instance Type : MSTI(1) Instance Status : Enabled Instance Priority : 32769(Bridge Priority : 32768, SYS ID Ext : 1 ) STP Instance Operational Status -------------------------------- Regional Root Bridge : 8193 /9C-D6-43-1E-B6-80 Internal Root Cost : 40000 Designated Bridge : 32769/C0-7B-BC-13-CA-86 Root Port : 9 Remaining Hops : 18 Last Topology Change : 1449 Topology Changes Count : 3 DGS-3200-10:4#show stp instance 2 Command: show stp instance 2 STP Instance Settings --------------------------- Instance Type : MSTI(2) Instance Status : Enabled Instance Priority : 61442(Bridge Priority : 61440, SYS ID Ext : 2 ) STP Instance Operational Status -------------------------------- Regional Root Bridge : 61442/34-08-04-2A-46-1C Internal Root Cost : 0 Designated Bridge : 61442/34-08-04-2A-46-1C Root Port : None Remaining Hops : 20 Last Topology Change : 19776 Topology Changes Count : 0 Итого: первый инст определился нормально. Относительно второго инста 3200 считает рутом себя. На циске вырублены все аклы, мультикаст фильтры и портфасты. На 3200 аналогично. Что я делаю не так? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
seelent Posted December 8, 2014 (edited) К 3200, кстати, прикреплен другой 3200, с аналогичной настройкой. Единственное но: на нем приоритет дефолтный. Им обоим в этом плане класть на 2 mst, даже если на одном из них сделать приоритет заведомо выше, считают себя в нем рутом и пусть весь мир подождет. Edited December 8, 2014 by seelent Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
seelent Posted December 8, 2014 Виноват, запарился, на аплинках 3200 не было нативного влана. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...