Jump to content

Как включить POE на Cisco2811

sunrise333
 Share

Recommended Posts

sunrise333

sunrise333

Posted
Posted (edited)

Всем привет.

 

Вопрос в названии темы.

 

TestNet2811#sh ver
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 15:56 by prod_rel_team

ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)

TestNet2811 uptime is 1 hour, 2 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.151-4.M5.bin"
Last reload type: Normal Reload

Cisco 2811 (revision 1.0) with 245760K/16384K bytes of memory.
Processor board ID FCZ113271W3
18 FastEthernet interfaces
2 Low-speed serial(sync/async) interfaces
1 Channelized E1/PRI port
1 Virtual Private Network (VPN) Module
2 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
500472K bytes of ATA CompactFlash (Read/Write)


License Info:

License UDI:

-------------------------------------------------
Device#   PID                   SN
-------------------------------------------------
*0        CISCO2811             FCZ113271W3

Configuration register is 0x2102

 

TestNet2811#sh inv
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811         , VID: V05 , SN: FCZ113271W3

NAME: "WAN Interface Card - Serial 2A/S on Slot 0 SubSlot 1", DESCR: "WAN Interface Card - Serial 2A/S"
PID: WIC-2A/S=         , VID: 1.0, SN: 18154642

NAME: "2nd generation two port FXS voice interface daughtercard on Slot 0 SubSlot 2", DESCR: "2nd generation two port FXS voice interface daughtercard"
PID: VIC2-2FXS         , VID: V01 , SN: FOC11273SW5

NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 3", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-1MFT-T1/E1  , VID: V01 , SN: FOC11505XTA

NAME: "PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with one DSP"
PID: PVDM2-16          , VID: V01 , SN: FOC11296V37

NAME: "16 Port 10BaseT/100BaseTX EtherSwitch on Slot 1", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
PID: NM-16ESW=         , VID: 1.0, SN: FOC09344XJ8

NAME: "Power daughter card for 16 port EtherSwitch NM on Slot 1 SubSlot 0", DESCR: "Power daughter card for 16 port EtherSwitch NM"
PID: PPWR-DCARD-16ESW  , VID: V01 , SN: FOC09490F34

 

TestNet2811#sh diag
Slot 0:
       C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports
       Port adapter is analyzed
       Port adapter insertion time 01:03:56 ago
       Onboard VPN             : v2.3.3
       EEPROM contents at hardware discovery:
       PCB Serial Number        : FOC11295FLJ
       Hardware Revision        : 1.0
       Top Assy. Part Number    : 800-26920-04
       Board Revision           : A0
       Deviation Number         : 0
       Fab Version              : 04
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Processor type           : 87
       Hardware date code       : 20070722
       Chassis Serial Number    : FCZ113271W3
       Chassis MAC Address      : 0007.0e62.f238
       MAC Address block size   : 24
       CLEI Code                : COM7R00ARA
       Product (FRU) Number     : CISCO2811
       Part Number              : 73-10258-05
       Version Identifier       : V05
       EEPROM format version 4
       EEPROM contents (hex):
         0x00: 04 FF C1 8B 46 4F 43 31 31 32 39 35 46 4C 4A 40
         0x10: 03 E7 41 01 00 C0 46 03 20 00 69 28 04 42 41 30
         0x20: 88 00 00 00 00 02 04 03 00 81 00 00 00 00 04 00
         0x30: 09 87 83 01 32 41 42 C2 8B 46 43 5A 31 31 33 32
         0x40: 37 31 57 33 C3 06 00 07 0E 62 F2 38 43 00 18 C6
         0x50: 8A 43 4F 4D 37 52 30 30 41 52 41 CB 8F 43 49 53
         0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12
         0x70: 05 89 56 30 35 20 D9 02 40 C1 FF FF FF FF FF FF

       PVDM Slot 0:
       16-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
       Hardware Revision        : 4.0
       Part Number              : 73-8538-05
       Board Revision           : B0
       Deviation Number         : 0
       Fab Version              : 04
       PCB Serial Number        : FOC11296V37
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Processor type           : 00
       Product (FRU) Number     : PVDM2-16
       Version Identifier       : V01
       EEPROM format version 4
       EEPROM contents (hex):
         0x00: 04 FF 40 03 EF 41 04 00 82 49 21 5A 05 42 42 30
         0x10: 88 00 00 00 00 02 04 C1 8B 46 4F 43 31 31 32 39
         0x20: 36 56 33 37 03 00 81 00 00 00 00 04 00 09 00 CB
         0x30: 88 50 56 44 4D 32 2D 31 36 89 56 30 31 20 D9 02
         0x40: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

       WIC Slot 1:
       Serial 2A/S (12in1)
       Hardware revision 1.0           Board revision C0
       Serial number     18154642      Part number    800-03182-01
       FRU Part Number     WIC-2A/S=
       Test history      0x0           RMA number     00-00-00
       Connector type    PCI
       EEPROM format version 1
       EEPROM contents (hex):
         0x20: 01 13 01 00 01 15 04 92 50 0C 6E 01 00 00 00 00
         0x30: 60 00 00 00 00 02 07 00 FF FF FF FF FF FF FF FF

       WIC Slot 2:
       2nd generation - FXS Voice daughter card (2 port)
       Hardware Revision        : 3.1
       Top Assy. Part Number    : 800-21341-02
       Board Revision           : B0
       Deviation Number         : 0-0
       Fab Version              : 01
       PCB Serial Number        : FOC11273SW5
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Product (FRU) Number     : VIC2-2FXS
       Version Identifier       : V01
       CLEI Code                : CNUIAPPAAA
       EEPROM format version 4
       EEPROM contents (hex):
         0x00: 04 FF 40 00 47 41 03 01 C0 46 03 20 00 53 5D 02
         0x10: 42 42 30 80 00 00 00 00 02 01 C1 8B 46 4F 43 31
         0x20: 31 32 37 33 53 57 35 03 00 81 00 00 00 00 04 00
         0x30: CB 89 56 49 43 32 2D 32 46 58 53 89 56 30 31 20
         0x40: C6 8A 43 4E 55 49 41 50 50 41 41 41 FF FF FF FF
         0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

       WIC Slot 3:
       VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1
       Hardware Revision        : 0.0
       Top Assy. Part Number    : 800-22628-05
       Board Revision           : B0
       Deviation Number         : 0
       Fab Version              : 04
       PCB Serial Number        : FOC11505XTA
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Product (FRU) Number     : VWIC2-1MFT-T1/E1
       Version Identifier       : V01
       EEPROM format version 4
       EEPROM contents (hex):
         0x00: 04 FF 40 03 FD 41 00 00 C0 46 03 20 00 58 64 05
         0x10: 42 42 30 88 00 00 00 00 02 04 C1 8B 46 4F 43 31
         0x20: 31 35 30 35 58 54 41 03 00 81 00 00 00 00 04 00
         0x30: CB 90 56 57 49 43 32 2D 31 4D 46 54 2D 54 31 2F
         0x40: 45 31 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF
         0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Slot 1:
       FastEthernet Port adapter, 16 ports
       Port adapter is analyzed
       Port adapter insertion time 01:03:56 ago
       EEPROM contents at hardware discovery:
       Hardware Revision        : 1.0
       Top Assy. Part Number    : 800-15156-01
       Board Revision           : E0
       Deviation Number         : 0-0
       Fab Version              : 03
       PCB Serial Number        : FOC09344XJ8
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Base MAC Address         : 0014.6a76.462c
       MAC Address block size   : 17
       Product (FRU) Number     : NM-16ESW=
       EEPROM format version 4
       EEPROM contents (hex):
         0x00: 04 FF 40 02 A9 41 01 00 C0 46 03 20 00 3B 34 01
         0x10: 42 45 30 80 00 00 00 00 02 03 C1 8B 46 4F 43 30
         0x20: 39 33 34 34 58 4A 38 03 00 81 00 00 00 00 04 00
         0x30: CF 06 00 14 6A 76 46 2C 43 00 11 FF FF FF FF FF
         0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

       16-Port Power Daughter Card
       Hardware Revision        : 1.0
       PCB Serial Number        : FOC09490F34
       Part Number              : 73-6610-02
       Board Revision           : A1
       RMA Test History         : 00
       RMA Number               : 0-0-0-0
       RMA History              : 00
       Deviation Number         : 0-0
       Top Assy. Part Number    : 65535-16777215-255
       CLEI Code                : CNSPN10AAA
       Product (FRU) Number     : PPWR-DCARD-16ESW
       Version Identifier       : V01

       EEPROM format version 4
       EEPROM contents (hex):
         0x00: 04 FF 40 02 B3 41 01 00 C1 8B 46 4F 43 30 39 34
         0x10: 39 30 46 33 34 82 49 19 D2 02 42 41 31 03 00 81
         0x20: 00 00 00 00 04 00 80 00 00 00 00 C0 46 FF FF FF
         0x30: FF FF FF C6 8A 43 4E 53 50 4E 31 30 41 41 41 CB
         0x40: 90 50 50 57 52 2D 44 43 41 52 44 2D 31 36 45 53
         0x50: 57 89 56 30 31 20 FF FF FF FF FF FF FF FF FF FF
         0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
         0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

вопрос поддержки Overview of Cisco Network Modules for Cisco Access Routers

 

Ммда. Отвечу сам себе, а мож кому станет легче.

 

1. Integrated internal inline power supply (such as PWR-28XX-AC-IP) or an 
external power supply (such as PWR-CHASSIS-360W) is recommended for the 
NM-XXESW-PWR selection made. 
2. Power Over Ethernet (POE) requires an AC plus IP system power supply 
(such as PWR-28XX-AC-IP).

Edited by sunrise333

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing
×
×
  • Create New...
На сайте используются файлы cookie и сервисы аналитики для корректной работы форума и улучшения качества обслуживания. Продолжая использовать сайт, вы соглашаетесь с использованием файлов cookie и с Политикой конфиденциальности.