Jump to content
Калькуляторы

Драйвер igb не создает eth-устройства для Intel 82576

Поставил в интеловский сервер карточку на чипсете Intel 82576, двухпортовую. Делаю modprobe igb. Драйвер загружается но устройства не добавляются. Хотя на том же сервере встроенные сетевухи на 82574 загружаются нормально по modprobe e1000e. Дистрибутив самосбор на флешке, ядро ванильное, драйвера для интела скомпилированы в виде модулей,пропиэретарные прошивки присутствуют,

 

vpn#uname -a
Linux vpn1 3.4.36-build-0003 #2 SMP Thu Mar 21 13:48:23 YEKT 2013 i686 GNU/Linux

vpn#dmesg | grep igb
igb: Intel(R) Gigabit Ethernet Network Driver - version 3.2.10-k

vpn#dmesg | grep e1000e
[    6.193123] e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k
[    6.252810] e1000e: Copyright(c) 1999 - 2012 Intel Corporation.
[    6.312758] e1000e 0000:00:19.0: setting latency timer to 64
[    6.312803] e1000e 0000:00:19.0: (unregistered net_device): Interrupt Throttling Rate (ints/sec) set to 35000
[    6.373678] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    6.681823] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:6f:1c:89
[    6.742214] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    6.802334] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF
[    6.862356] e1000e 0000:02:00.0: Disabling ASPM L0s L1
[    6.922260] e1000e 0000:02:00.0: (unregistered net_device): Interrupt Throttling Rate (ints/sec) set to 35000
[    6.982453] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[    6.982455] e1000e 0000:02:00.0: irq 46 for MSI/MSI-X
[    6.982458] e1000e 0000:02:00.0: irq 47 for MSI/MSI-X
[    7.089613] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:6f:1c:88
[    7.148591] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection
[    7.206361] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF
[    7.605870] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[    7.706842] e1000e 0000:00:19.0: irq 44 for MSI/MSI-X
[  138.362637] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx
[  190.600942] e1000e: eth0 NIC Link is Down
[  209.343423] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx
[  281.865721] e1000e: eth1 NIC Link is Down
[  296.907129] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx
[  371.523975] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

vpn#lsmod
Module                  Size  Used by    Tainted: G  
igb                    87520  0 
sha1_generic            1553 168 
arc4                    1006 84 
ecb                     1468 84 
ppp_mppe                4513 84 
act_police              3154 262 
sch_ingress             1227 262 
sch_tbf                 3117 262 
cls_u32                 5141 337 
sch_sfq                 6968 77 
iptable_filter          1127  1 
iptable_raw              971  1 
xt_CT                   2742  1 
nf_conntrack           54919  1 xt_CT
xt_TCPMSS               1800  1 
xt_tcpudp               1676  1 
iptable_mangle          1164  1 
ip_tables               8208  3 iptable_filter,iptable_raw,iptable_mangle
sch_htb                10804  1 
pptp                   12827 544 
gre                     1328  1 pptp
pppox                   1589  1 pptp
ppp_generic            18505 1091 ppp_mppe,pptp,pppox
slhc                    3846  1 ppp_generic
ipt_NETFLOW            18119  3 
x_tables               11790  8 iptable_filter,iptable_raw,xt_CT,xt_TCPMSS,xt_tcpudp,iptable_mangle,ip_tables,ipt_NETFLOW
8021q                  13147  0 
garp                    4727  1 8021q
stp                     1369  1 garp
llc                     3514  2 garp,stp
dca                     4574  1 igb
e1000e                114954  0 

 

Где может быть проблема или я этот igb не так загружаю.

Edited by uropek

Share this post


Link to post
Share on other sites

lspci в студию.

00:00.0 Host bridge: Intel Corporation Device 0158 (rev 09)
00:19.0 Ethernet controller: Intel Corporation Device 1502 (rev 05)
00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05)
00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5)
00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5)
00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5)
00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Device 1c54 (rev 05)
00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05)
02:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 07)

Share this post


Link to post
Share on other sites

Похоже на то:

Платформа Intel 1U R1304BTLSHBNR (LGA1155, C204, SVGA, SATA RAID, 4xHotSwap SAS / SATA, 2xGbLAN, 4DDR-III, 350W)

Серверный корпус R1304 с установленной в нем платой S1200BTL

 

а сетевку пробую вставить Intel < E1G42ET> Gigabit Adapter Dual Port (OEM) PCI-E x4 10 / 100 / 1000Mbps.

 

Но слот к сожалению один или все таки не один (может быть не рассмотрел). Как выбор менять платформу?

Edited by uropek

Share this post


Link to post
Share on other sites

 

Что значит 1 слот? На фото вашей платы 4 слота видно, воткните в другой.

Это довольно сложно сделать в одноюнитовом корпусе 8)

Share this post


Link to post
Share on other sites

http://serverconfigurator2.intel.com/sctthol.aspx?search=Server+Board+S1200BTL

 

Они прикалываются, четырехпортовые сетевушки есть, а двухпортовых в списке нет на чипе 82576.

 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.