Jump to content
Калькуляторы

Странный Called Party Number Стыкую Cisco 2821 с АТС МС-240

Подключили поток от АТС МС-240, проверяем входящие. При попытке позвонить на на номер получаем такой трейс:

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x000D

Bearer Capability i = 0x9090A3

Standard = CCITT

Transfer Capability = 3.1kHz Audio

Transfer Mode = Circuit

Transfer Rate = 64 kbit/s

Channel ID i = 0xA9838C

Exclusive, Channel 12

Progress Ind i = 0x8081 - Call not end-to-end ISDN, may have in-band info

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: Received SETUP callref = 0x800D callID = 0x0047 switch = primary-net5 interface = User

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: TX -> SETUP_ACK pd = 8 callref = 0x800D

Channel ID i = 0xA9838C

Exclusive, Channel 12

Progress Ind i = 0x8188 - In-band info or appropriate now available

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x000D

Called Party Number i = 0xC1, '6'

Plan:ISDN, Type:Subscriber(local)

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x000D

Called Party Number i = 0xC1, '7'

Plan:ISDN, Type:Subscriber(local)

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x000D

Called Party Number i = 0xC1, '3'

Plan:ISDN, Type:Subscriber(local)

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x000D

Called Party Number i = 0xC1, '0'

Plan:ISDN, Type:Subscriber(local)

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x000D

Called Party Number i = 0xC1, '1'

Plan:ISDN, Type:Subscriber(local)

Sending Complete

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x800D

Cause i = 0x809C - Invalid number format (incomplete number)

Nov 29 11:13:07: ISDN Se0/0/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x000D

Номер на который звоним 67301.

Конфиг:

isdn switch-type primary-net5

translation-rule 1

Rule 0 ^90 0

Rule 1 ^91 1

Rule 2 ^92 2

Rule 3 ^93 3

Rule 4 ^94 4

Rule 5 ^95 5

Rule 6 ^96 6

Rule 7 ^97 7

Rule 8 ^98 8

Rule 9 ^99 9

controller E1 0/0/0

framing NO-CRC4

pri-group timeslots 1-31

interface Serial0/0/0:15

no ip address

encapsulation hdlc

load-interval 30

isdn switch-type primary-net5

isdn overlap-receiving

isdn incoming-voice voice

isdn calling-party-num network-provided

isdn send-alerting

isdn bchan-number-order ascending

isdn sending-complete

no cdp enable

dial-peer voice 100 pots

destination-pattern 9T

translate-outgoing called 1

clid network-number 4167301

port 0/0/0:15

forward-digits all

Помогите справится с проблемой! Буду признателен ;-)

Share this post


Link to post
Share on other sites

Обращались в нашу ТП с похожей проблемой при стыке МС-240 с CISCO (к сожалению не знаю модель CISCO).

При наборе overlap CISCO всегда отбивала с причиной "incomplete number".

Заработало когда на МС-240 настроили набор enblock. Попробуйте сделать так же.

 

п.с. а еще в логе не видать calling-номера. его действительно нет в вызове? или CISCO его просто не печатает?

 

п.п.с. если МС-240 под вашим управлением, то можете обратиться в ТП "ЭЛТЕКС":

тел. 8 (383) 272-83-31 доб. 3019

anna.zhadovets@eltex.nsk.ru

Edited by Bokrenok

Share this post


Link to post
Share on other sites

Это вся конфигурация Cisco? Мне видится, что у вас нет подходящего dial-peer для маршрутизации вызова.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this