viki Опубликовано 6 мая, 2011 · Жалоба Всем доброго времени суток. помогите плиз...Ситуация следующая пришли к нам в универ циски, установили стенды с данным оборудованием... но как настроить книжек нету =( с точкой доступа там немного проще через веб интерфейс настраивается а как подключиться к CISCo 881 W ? я так понимаю надо через Гипер терминал или путти.... указать 9600 и вперед... а куда дальше? как настроить точку доступа на маршрутезаторе 881W ? какими командами? как настроить шифрование? как включить SSID? есть ли детальная книжечка по данному продукту? кто может выложите, подскажите!!! СПАИБО ВАМ НЕ ЧЕЛОВЕЧЕСКОЕ""" Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
GFORGX Опубликовано 6 мая, 2011 · Жалоба Google, Google, Google. http://forums.whirlpool.net.au/archive/1277454 Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
applx Опубликовано 6 мая, 2011 (изменено) · Жалоба dot11 ssid ***SSID NAME*** vlan ***VLAN NUMBER*** authentication open authentication key-management wpa guest-mode wpa-psk ascii ***password*** ! interface Dot11Radio0 no ip address ! encryption vlan ***VLAN NUMBER*** mode ciphers tkip ! ! ssid ***SSID NAME*** ! channel ***CHANNEL NUMBER*** station-role root ! interface Dot11Radio0.x encapsulation dot1Q ***VLAN NUMBER*** ip address x.x.x.x y.y.y.y Изменено 6 мая, 2011 пользователем applx Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
viki Опубликовано 17 мая, 2011 · Жалоба всем привет вообщем делаю следущее шаг 1 )Router(config)# interface wlan-ap0 Router(config-if)# шаг 2) Router(config-if)# ip address 10.21.0.20 255.255.255.0 or Router(config-if)# ip unnumbered vlan1 шаг 3) no shut Example: Router(config-if)# no shut шаг 4) Router(config-if)# ip address 10.10.0.30 255.255.255.0 шаг 5) Router(config-if)# exit Router(config)# шаг 6) Router(config)# exit Router# шаг 7) Router# service-module wlan-ap0 session Trying 10.21.0.20, 2002 ... Open ap> после этого надо настраивать Enabling the Radio Interface ? 1. configure terminal 2. dot11 ssid ssid 3. interface dot11radio {0} 4. ssid ssid 5. no shutdown 6. end 7. copy running-config startup-config просто в беспроводных сетях не видно имя моей ssid сети... что еще надо сделать? Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
viki Опубликовано 17 мая, 2011 · Жалоба есть кто может подсказать ? почему не вижу wifi сеть циско? Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
Alexey K Опубликовано 17 мая, 2011 (изменено) · Жалоба есть кто может подсказать ? почему не вижу wifi сеть циско? Привет :) Покажите, пожалуйста, вывод команды sh run Изменено 17 мая, 2011 пользователем Alexey K Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
viki Опубликовано 18 мая, 2011 · Жалоба ap#show run Building configuration... Current configuration : 2710 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ap ! enable secret 5 $1$qC5D$CanuPMZNUe7QOm95wikSx0 ! no aaa new-model ! ! dot11 syslog ! dot11 ssid TEST ! ! ! username cisco privilege 15 secret 5 $1$cxpJ$XsQLwxvlOG677QFsoDnqj/ ! ! bridge irb ! ! interface Dot11Radio0 description WIFI Interface no ip address no ip route-cache ! ssid TEST ! antenna gain 0 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 description Wireless Interface ip address 192.168.0.1 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! banner exec ^CC % Password change notice. ----------------------------------------------------------------------- Default username/password setup on AP is cisco/cisco with privilege level 15. It is strongly suggested that you create a new username with privilege level 15 using the following command for console security. username <myuser> privilege 15 secret 0 <mypassword> no username cisco Replace <myuser> and <mypassword> with the username and password you want to use. After you change your username/password you can turn off this message by configuring "no banner login" and "no banner exec" in privileged mode. ----------------------------------------------------------------------- ^C banner login ^CC % Password change notice. ----------------------------------------------------------------------- Default username/password setup on AP is cisco/cisco with privilege level 15. It is strongly suggested that you create a new username with privilege level 15 using the following command for console security. username <myuser> privilege 15 secret 0 <mypassword> no username cisco Replace <myuser> and <mypassword> with the username and password you want to use. After you change your username/password you can turn off this message by configuring "no banner login" and "no banner exec" in privileged mode. ----------------------------------------------------------------------- ^C ! line con 0 privilege level 15 login local no activation-character line vty 0 4 login local ! cns dhcp end ap# Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
viki Опубликовано 18 мая, 2011 · Жалоба все получилось запустить WI FI после того как описано выше сделал следущее Аутентификацию шог 1) AP# configure terminal шаг 2) AP(config)#dot11 ssid **имя вашей сети** шаг 3) AP(config-ssid)#authentication open шаг 4) AP(config-ssid)# guest-mode шаг 5) AP(config-ssid)#end шаг 6) ap# copy running-config startup-config после выполненных действий появилась сеть. ap#copy running-config sta ap#copy running-config startup-config Destination filename [startup-config]? Building configuration... [OK] ap#Station: 4c0f.6e45.b038 roamed in with: First association to WLAN *Sep 6 05:46:48.259: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 4c0f.6e45.b038 Associated KEY_MGMT[NONE] *Sep 6 05:47:58.483: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 4c0f.6e45.b038 Reason: Sending station has left the BSS ap#sho ap#show run Building configuration... Current configuration : 2748 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ap ! enable secret 5 $1$qC5D$CanuPMZNUe7QOm95wikSx0 ! no aaa new-model ! ! dot11 syslog ! dot11 ssid TEST authentication open guest-mode ! ! ! username cisco privilege 15 secret 5 $1$cxpJ$XsQLwxvlOG677QFsoDnqj/ ! ! bridge irb ! ! interface Dot11Radio0 description WIFI Interface no ip address no ip route-cache ! ssid TEST ! antenna gain 0 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 description Wireless Interface ip address 192.168.0.1 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! banner exec ^CC % Password change notice. ----------------------------------------------------------------------- Default username/password setup on AP is cisco/cisco with privilege level 15. It is strongly suggested that you create a new username with privilege level 15 using the following command for console security. username <myuser> privilege 15 secret 0 <mypassword> no username cisco Replace <myuser> and <mypassword> with the username and password you want to use. After you change your username/password you can turn off this message by configuring "no banner login" and "no banner exec" in privileged mode. ----------------------------------------------------------------------- ^C banner login ^CC % Password change notice. ----------------------------------------------------------------------- Default username/password setup on AP is cisco/cisco with privilege level 15. It is strongly suggested that you create a new username with privilege level 15 using the following command for console security. username <myuser> privilege 15 secret 0 <mypassword> no username cisco Replace <myuser> and <mypassword> with the username and password you want to use. After you change your username/password you can turn off this message by configuring "no banner login" and "no banner exec" in privileged mode. ----------------------------------------------------------------------- ^C ! line con 0 privilege level 15 login local no activation-character line vty 0 4 login local ! cns dhcp end ap#onf ap#con ap#conf ap#configure t ap#configure terminal Enter configuration commands, one per line. End with CNTL/Z. ap(config)#dot11 ssid TEST ap(config-ssid)#end ap# *Sep 6 06:01:57.779: %SYS-5-CONFIG_I: Configured from console by cisco on console ap#show run Building configuration... Current configuration : 2748 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ap ! enable secret 5 $1$qC5D$CanuPMZNUe7QOm95wikSx0 ! no aaa new-model ! ! dot11 syslog ! dot11 ssid TEST authentication open guest-mode ! ! ! username cisco privilege 15 secret 5 $1$cxpJ$XsQLwxvlOG677QFsoDnqj/ ! ! bridge irb ! ! interface Dot11Radio0 description WIFI Interface no ip address no ip route-cache ! ssid TEST ! antenna gain 0 station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface BVI1 description Wireless Interface ip address 192.168.0.1 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag bridge 1 route ip ! ! banner exec ^CC % Password change notice. ----------------------------------------------------------------------- Default username/password setup on AP is cisco/cisco with privilege level 15. It is strongly suggested that you create a new username with privilege level 15 using the following command for console security. username <myuser> privilege 15 secret 0 <mypassword> no username cisco Replace <myuser> and <mypassword> with the username and password you want to use. After you change your username/password you can turn off this message by configuring "no banner login" and "no banner exec" in privileged mode. ----------------------------------------------------------------------- ^C banner login ^CC % Password change notice. ----------------------------------------------------------------------- Default username/password setup on AP is cisco/cisco with privilege level 15. It is strongly suggested that you create a new username with privilege level 15 using the following command for console security. username <myuser> privilege 15 secret 0 <mypassword> no username cisco Replace <myuser> and <mypassword> with the username and password you want to use. After you change your username/password you can turn off this message by configuring "no banner login" and "no banner exec" in privileged mode. ----------------------------------------------------------------------- ^C ! line con 0 privilege level 15 login local no activation-character line vty 0 4 login local ! cns dhcp end ap# Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
viki Опубликовано 24 мая, 2011 · Жалоба Всем привет , есть вопрос как настроить Radius server в cisco 881w ? чтобы клиенты когда подцеплялись по воздуху проходили через цисковский Radius? кроме как подключиться по поздуху ( без шифрования) листинг выше.... там не настроено, что надо для того чтобы настроить этот самый радиус? Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
dimas Опубликовано 15 октября, 2014 · Жалоба Апну тему, чтобы не дублировать топики .. На 881w можно выключить встроенную AP? Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...