[stacy]

Привет всем!

 

Сразу скажу, что задачу, которая описана ниже мне хочеться решить просто из интереса, потому что практически есть и другие пути, но все таки интересено, может как-нибудь получится :)

Итак:

 

Имеется такая конфигурация:

[user]--dialup_link--[helix-max TNT]---l2tp_tunnel---[jackal - l2tp

LNS]--[private net]

 

Настраиваю l2tp LAC на TNT. при входящих звонках от юзера на макс - все

отлично, макс устанавливает l2tp туннель на jackal. Юзерная PPP сессия

прозрачно терминируеться на jackal, все отлично.

 

А вот если jackal запрашивает по l2tp у макса исходящий звонок на

какой-либо номер, все происходит так:

 

1. если профайл соединения требует локального (то есть на самом максе)

терминирования PPP, то все отлично, макс звонит, соединение

устанавливается,

затем сам макс выдает адрес пользователю и обрабатывает его траффик, то

есть jackal больше никак в этом не участвует.

 

2. Если требуется после исходящего звонка передача всего PPP траффика на

jackal и обратно, то есть нормальный туннель, начинаются глюки - как

только происходит соединение с модемом у пользователя и макс обнаруживает

carrier,

он тут же обрывает звонок.

 

В деталях это выглядит так:

 

1. jackal открывает l2tp сессию с одной из модемных карточек на максе,

авторизуется и посылает запрос на исходящий звонок.

2. Модемная карточка посылает запрос шелф-контроллеру на исходящий звонок.

3. Шелф контроллер находит свободный модем, и тот начинает набирать номер

4. Пользовательский модем отвечает и модемы зацепляются

5. тот из модемов на максе, который звонил, говорит:

 

L2TPCM: l2tpTransferDialout CInfo not found routeID:562

 

И кладет трубу.

 

---------------

Железо на максе такое:

 

admin> show

Shelf 1 ( standalone ):

Reqd Oper Slot Type

{ shelf-1 slot-1 0 } UP UP 4ether2-card

{ shelf-1 slot-2 0 } UP UP 8e1-card

{ shelf-1 slot-3 0 } UP UP 8e1-card

{ shelf-1 slot-4 0 } UP UP 48modem-56k-card

{ shelf-1 slot-5 } OCCUPIED

{ shelf-1 slot-6 0 } UP UP 48modem-56k-card

{ shelf-1 slot-7 } OCCUPIED

{ shelf-1 slot-8 0 } UP UP 48modem-56k-card

{ shelf-1 slot-9 } OCCUPIED

{ shelf-1 slot-10 0 } UP UP 48modem-56k-card

{ shelf-1 slot-11 } OCCUPIED

{ shelf-1 slot-12 0 } UP UP 48modem-56k-card

{ shelf-1 slot-13 } OCCUPIED

{ shelf-1 slot-14 0 } UP UP csmx-card

{ shelf-1 slot-15 0 } UP UP csmx-card

{ shelf-1 slot-16 0 } UP UP csmx-card

 

 

Софт - TAOS 9.0.9

 

 

Включенные фичи:

 

shelf-number = 1

software-version = 9

software-revision = 0

software-level = ""

manufacturer = dba-ascend-mfg

d-channel-enabled = yes

aim-enabled = yes

switched-enabled = yes

multi-rate-enabled = yes

t1-pri-conversion-enabled = no

frame-relay-enabled = yes

maxlink-client-enabled = enabled

data-call-enabled = yes

r2-signaling-enabled = yes

hardware-level = 0

countries-enabled = 511

domestic-enabled = yes

phs-2-1-support = no

modem-dialout-enabled = yes

firewalls-enabled = yes

ipsec-enabled = not-installed

network-management-enabled = yes

phs-support = no

selectools-enabled = yes

routing-protocols-disabled = no

tnt-adsl-restricted = no

tnt-sdsl-restricted = no

tnt-idsl-restricted = no

voip-enabled = yes

voip-max-capacity-allowed = no

xcom-ss7 = enabled

ss7asg = enabled

atmp-enabled = enabled

l2tp-enabled = enabled

pptp-enabled = enabled

l2f-enabled = enabled

ipinip-enabled = enabled

sdtn-enabled = disabled

vrouter-enabled = enabled

v110-enabled = disabled

rtfax-enabled = yes

maxtap-enabled = disabled

atmsvc-enabled = disabled

frvc-enabled = disabled

network-mgmt-voip-enabled = no

wormarq-enabled = disabled

nm-reporting-enabled = no

nm-vpn-enabled = no

nm-navis-radius-enabled = no

fgd-signaling-enabled = no

nm-prov = no

nm-prov-core = no

 

 

и лог файлы:

 

попытка 1 - в качестве LNS - openl2tp на линуксе:

 

лог файл с модема на который присоединяется LNS:

--------------------

L2TPCM-1: looking for 'jackal' shared secret... (CID='jackal' SID='')

L2TPCM-1: Updating Password -> 'zhopa0zhopa'

L2TPCM-1: Updating ServerAuthID -> 'helix'

L2TPCM-1: shared secret with 'jackal' is 'zhopa0zhopa'

L2TPCM-1: Parse SCCRQ

L2TPCM-1: .. Protocol Version = 0x0100

L2TPCM-1: .. Framing Cap = 0x00000003

L2TPCM-1: .. Bearer Cap = 0x00000003

L2TPCM-1: .. Firmware Revision = 0x0106

L2TPCM-1: .. Name = 'jackal' (expected 'jackal')

L2TPCM-1: .. Vendor = Katalix Systems Ltd. Linux

L2TPTRANS-1: setting peer's tunnel ID to 27249

L2TPTRANS-1: _sendAck: nextS = 0, nextR = 1

L2TPCM-1: .. TunnelID = 27249 (0x6A71)

L2TPCM-1: .. Receive Window Size = 10

L2TPTRANS-1: setting peer's max Tx window to 10

L2TPCM-1: .. Peer is challenging me!

L2TPCM-1: Session state change - Down -> Remote-Start

L2TPCM-1: Notifying L2TP MIB {{ 1 10 1 } 0} new state 2

L2TPCM-1: sending SCCRP; peerTunnelID=27249

L2TPCM-1: SCCRP: clientAuthID=[jackal] serverAuthID=[helix]

L2TPCM-1: starting L2TP CC Estb Timer for 60 seconds.

L2TPTRANS-1: sendAction: txWindow = 10, nextSend = 0

L2TPTRANS-1: _sendCtrl: nextS = 0, nextR = 1

L2TPTRANS-1: starting retry timer for 1000 milliseconds.

L2TPTRANS-1: State change - Idle -> TxWindowOpen

L2TPTRANS-1: processAck 1

L2TPTRANS-1: pulling seqNum 0 off of the queue

L2TPTRANS-1: State change - TxWindowOpen -> Idle

L2TPTRANS-1: _receiveAction: peersNextS = 1, myNextR = 1

L2TPTRANS-1: _sendAck: nextS = 1, nextR = 2

L2TPCM-1: transportRxCallback from [172.16.133.201:57929/1] on VR0

L2TPCM-1: Event = RxSCCCN

L2TPCM-1: Rx SCCN

L2TPCM-1: shared secret with 'jackal' is 'zhopa0zhopa'

L2TPCM-1: starting L2TP Hello Timer for 60 seconds.

L2TPCM-1: Session state change - Remote-Start -> Up

L2TPCM-1: Notifying L2TP MIB {{ 1 10 1 } 0} new state 3

L2TPTRANS-1: processAck 1

L2TPTRANS-1: processAck 1

L2TPTRANS-1: _receiveAction: peersNextS = 2, myNextR = 2

L2TPTRANS-1: _sendAck: nextS = 1, nextR = 3

L2TPCM-1: transportRxCallback from [172.16.133.201:57929/1] on VR0

L2TPCM-1: Event = RxOutCallReq

L2TPCM-1: Parse OCRQ

L2TPCM-1: .. peersCallId = 35362

L2TPCM-1: .. peersCallSerialNumber=0

L2TPCM-1: .. Min BPS = 0

L2TPCM-1: .. Max BPS = 0

L2TPCM-1: .. Bearer Type = 0x00000002

L2TPCM-1: .. Framing Type = 0x00000002

L2TPCM-1: .. Dialed number = <screened>

L2TPCM-#0: Connection state change - <destroyed> -> Idle

?L2TPCM: Connection state change (Idle) but no CID [yet]

L2TPCM: Dialout Profile Name passed in a VSA:sks-dialout

L2TPCM: placeOutgoingCall sending DIALOUT REQ to Shelf

L2TPCM-1-#0: Connection state changed to CALLING

L2TPCM-0: Event = ControlBusMsg

L2TPCM: _l2tpCBHost Msg: L2TPCB_DIALOUT_RSP len: 117

L2TPCM: Received L2TPCB_DIALOUT_RSP msg peersCallid:35362 routeID:562

L2TPCM: Connection is Hosted on a diff slot: routeID: 562

L2TPCM-1: sending OCRP, myCID=562 hisCID=35362

L2TPCM-#562: Connection state change - Idle -> Calling

L2TPCM-1-562: Notifying L2TP MIB {{1 10 1} 562} new state 2

L2TPTRANS-1: sendAction: txWindow = 10, nextSend = 1

L2TPTRANS-1: _sendCtrl: nextS = 1, nextR = 3

L2TPTRANS-1: starting retry timer for 1000 milliseconds.

L2TPTRANS-1: State change - Idle -> TxWindowOpen

L2TPTRANS-1: processAck 2

L2TPTRANS-1: pulling seqNum 1 off of the queue

L2TPTRANS-1: State change - TxWindowOpen -> Idle

L2TPCM-1: Event = CallTimerExpired

?L2TPCM-1: Call timer expired; route 0 not found

L2TPCM-1: Event = SessionTimerExpired

L2TPCM-1: sending Hello

L2TPCM-1: starting Hello Timer for 60 seconds.

L2TPTRANS-1: sendAction: txWindow = 10, nextSend = 2

L2TPTRANS-1: _sendCtrl: nextS = 2, nextR = 3

L2TPTRANS-1: starting retry timer for 1000 milliseconds.

L2TPTRANS-1: State change - Idle -> TxWindowOpen

L2TPTRANS-1: processAck 3

L2TPTRANS-1: pulling seqNum 2 off of the queue

L2TPTRANS-1: State change - TxWindowOpen -> Idle

L2TPCM-1: Event = SessionTimerExpired

L2TPCM-1: sending Hello

L2TPCM-1: starting Hello Timer for 60 seconds.

L2TPTRANS-1: sendAction: txWindow = 10, nextSend = 3

L2TPTRANS-1: _sendCtrl: nextS = 3, nextR = 3

L2TPTRANS-1: starting retry timer for 1000 milliseconds.

L2TPTRANS-1: State change - Idle -> TxWindowOpen

L2TPTRANS-1: processAck 4

L2TPTRANS-1: pulling seqNum 3 off of the queue

L2TPTRANS-1: State change - TxWindowOpen -> Idle

L2TPTRANS-1: _receiveAction: peersNextS = 3, myNextR = 3

L2TPTRANS-1: _sendAck: nextS = 4, nextR = 4

L2TPCM-1: transportRxCallback from [172.16.133.201:57929/1] on VR0

L2TPCM-1: Event = RxCallDiscNotify

?L2TPCM: avpLen 8 too short - should be >= 10

L2TPCM-1: rx CDN; myCID=0 hisCID=35362 RC=? EC=?

L2TPCM-#562: Connection state change - Calling -> <destroyed>

L2TPCM-1-562: Notifying L2TP MIB {{1 10 1} 562} new state 100

mdm56k-1/10> debug off

Diagnostic output disabled

mdm56k-1/10> quit

 

лог с модема который набирал номер и устанавливал соединение:

---------------------------

 

L2TPCM-0: Event = ControlBusMsg

L2TPCM: _l2tpCBHost Msg: ???? len: 117

ENCAPFSM-83: WAN state change, route 562

ENCAPFSM-83: >> RouteID 562, state INACTIVE, event OPEN_OUT_REQ

ENCAP-83: inactiveOpenOut, prof sks-dialout.

ENCAPFSM-83: << RouteID 562, state CALLING

 

ENCAPFSM: Call state change, port 47, connected 1, carrier 0

ENCAPFSM-83: WAN state change, route 562

ENCAPFSM-83: >> RouteID 562, state CALLING, event CALL_CONNECTED

ENCAPFSM: EVENT IGNORED

ENCAPFSM-83: << RouteID 562, state CALLING

 

OK

ENCAPFSM: Call state change, port 47, connected 1, carrier 1

ENCAPFSM-83: WAN state change, route 562

ENCAPFSM-83: >> RouteID 562, state CALLING, event CARRIER_EST

ENCAPFSM-83: callingCarrierEst

ENCAPFSM-83: openEncapsLayer.

L2TPCM: l2tpTransferDialout CInfo not found routeID:562

ENCAPFSM-83: << RouteID 562, state OPENING

 

ENCAPFSM: Call state change, port 47, connected 0, carrier 0

ENCAPFSM-83: WAN state change, route 562

ENCAPFSM-83: >> RouteID 562, state OPENING, event CALL_DISCONNECTED

ENCAPFSM-83: closing encaps

ENCAPFSM-83: ENCAPS state change, route 562

ENCAPFSM-83: << RouteID 562, state DOWN

 

ENCAPFSM-83: WAN state change, route 562

ENCAPFSM-83: >> RouteID 562, state DOWN, event ENCAPS_CLOSED

L2TPCM: wanDataL2tpCallCleared for routeID:562

ENCAPFSM-0: << RouteID 0, state (unused)

 

L2TUNNEL-1750: CheckIncomingCall

Modem=(1 1 47) [MBID 562]:

 

OK

1FF8

 

TERMINATION REASON...........LOCAL REQUEST

LAST TX data rate............52000 BPS

HIGHEST TX data rate.........52000 BPS

LAST RX data rate............28800 BPS

HIGHEST RX data rate.........28800 BPS

Error correction PROTOCOL....LAPM

Data COMPRESSION.............V42Bis

Digital Pad Detected.........

Line QUALITY.................36

Receive LEVEL................15

Highest SPX Receive State....67

Highest SPX Transmit State...68

Last SPX Receive State.......67

Last SPX Transmit State......68

EQM sum Value................19

RBS Pattern detected.........N/A

Data Rate Dropped in kbps....N/A

Local Retrain Count..........0

Remote Retrain Count.........0

Local Rate Reneg Count.......0

Remote Rate Reneg Count......0

Flex 9481814347E8 Failed / Connected V.90

 

OK

Modem=(1 1 47) [MBID 562]:

BEGINaa48ab48ac48ad48ba14bb14bc14bd14ca77cb67cc236cd237da4ea0eb0fa100fb100fc100g

a12gb0ha36hb36hc36hd0he156hf25hg0hh255hi255h

j255hk255hl255hm255hn255ho255hp255hq255hr255hs255ia28ib28ic28ja0jb0jc0jd0je0jf0k

a1kb0kc0kd1ke0kf16kg0kh0ki38kj0kk0kl90km97kn

255ko78kp160kq254kr31la104lb103lc104ld103ma0mb0mc5na0nb0oa255ob255oc255pa1pb0pc0

pd0pe0pf0pg0ph0pi240pj246pk198pl4pm0pn0po0pp

0qa0qb0qc255ra90rb0rc0rd0re0rf0rg0rh229sa255sb255sc31sd248ta23tb0tc96td218te0tf2

55tg255th0ti0END

-----------------------

 

 

Попытка 2 - в качестве LNS - mpd-5.3 на freeBSD

Лог снимался только с модема на который посоединялся LNS,

во всем остальном - поведение итд - ситуация такая же.

------------------

 

csmx-1/14> debug on

Diagnostic output enabled

csmx-1/14> L2TPCM-0: transportRxCallback from [172.16.133.1:61538/0] on VR0

L2TPCM-0: Event = RxSCCRQ

L2TPCM-24: Session state change - <destroyed> -> Down

L2TPCM-24: Notifying L2TP MIB {{ 1 14 24 } 0} new state 1

L2TPCM-24: remote start new session [172.16.133.1:61538/7306]

L2TPTRANS-24: Start called

L2TPTRANS-24: START: IP = [172.16.133.1:61538]

L2TPCM-24: looking for 'twister' shared secret... (CID='twister' SID='')

L2TPCM-24: Updating Password -> 'zhopa0zhopa'

L2TPCM-24: Updating ServerAuthID -> 'helix'

L2TPCM-24: shared secret with 'twister' is 'zhopa0zhopa'

L2TPCM-24: Parse SCCRQ

L2TPCM-24: .. Name = 'twister' (expected 'twister')

L2TPCM-24: .. Vendor = FreeBSD MPD

L2TPCM-24: .. Bearer Cap = 0x00000003

L2TPCM-24: .. Receive Window Size = 8

L2TPTRANS-24: setting peer's max Tx window to 8

L2TPCM-24: .. Protocol Version = 0x0100

L2TPCM-24: .. Framing Cap = 0x00000003

L2TPTRANS-24: setting peer's tunnel ID to 7306

L2TPTRANS-24: _sendAck: nextS = 0, nextR = 1

L2TPCM-24: .. TunnelID = 7306 (0x1C8A)

L2TPCM-24: .. Peer is challenging me!

L2TPCM-24: Session state change - Down -> Remote-Start

L2TPCM-24: Notifying L2TP MIB {{ 1 14 24 } 0} new state 2

L2TPCM-24: sending SCCRP; peerTunnelID=7306

L2TPCM-24: SCCRP: clientAuthID=[twister] serverAuthID=[helix]

L2TPCM-24: starting L2TP CC Estb Timer for 60 seconds.

L2TPTRANS-24: sendAction: txWindow = 8, nextSend = 0

L2TPTRANS-24: _sendCtrl: nextS = 0, nextR = 1

L2TPTRANS-24: starting retry timer for 1000 milliseconds.

L2TPTRANS-24: State change - Idle -> TxWindowOpen

L2TPTRANS-24: processAck 1

L2TPTRANS-24: pulling seqNum 0 off of the queue

L2TPTRANS-24: State change - TxWindowOpen -> Idle

L2TPTRANS-24: _receiveAction: peersNextS = 1, myNextR = 1

L2TPTRANS-24: _sendAck: nextS = 1, nextR = 2

L2TPCM-24: transportRxCallback from [172.16.133.1:61538/24] on VR0

L2TPCM-24: Event = RxSCCCN

L2TPCM-24: Rx SCCN

L2TPCM-24: shared secret with 'twister' is 'zhopa0zhopa'

L2TPCM-24: starting L2TP Hello Timer for 60 seconds.

L2TPCM-24: Session state change - Remote-Start -> Up

L2TPCM-24: Notifying L2TP MIB {{ 1 14 24 } 0} new state 3

L2TPTRANS-24: processAck 1

L2TPTRANS-24: _receiveAction: peersNextS = 2, myNextR = 2

L2TPTRANS-24: _sendAck: nextS = 1, nextR = 3

L2TPCM-24: transportRxCallback from [172.16.133.1:61538/24] on VR0

L2TPCM-24: Event = RxOutCallReq

L2TPCM-24: Parse OCRQ

L2TPCM-24: .. peersCallId = 28906

L2TPCM-24: .. peersCallSerialNumber=72

L2TPCM-24: .. Dialed number = <screened>

L2TPCM-24: .. Min BPS = 0

L2TPCM-24: .. Max BPS = 2147483647

L2TPCM-24: .. Bearer Type = 0x00000003

L2TPCM-24: .. Framing Type = 0x00000003

L2TPCM-#0: Connection state change - <destroyed> -> Idle

?L2TPCM: Connection state change (Idle) but no CID [yet]

L2TPCM: Dialout Profile Name passed in a VSA:sks-dialout

L2TPCM: placeOutgoingCall sending DIALOUT REQ to Shelf

L2TPCM-24-#0: Connection state changed to CALLING

L2TPCM-0: Event = ControlBusMsg

L2TPCM: _l2tpCBHost Msg: L2TPCB_DIALOUT_RSP len: 117

L2TPCM: Received L2TPCB_DIALOUT_RSP msg peersCallid:28906 routeID:1922

L2TPCM: Connection is Hosted on a diff slot: routeID: 1922

L2TPCM-24: sending OCRP, myCID=1922 hisCID=28906

L2TPCM-#1922: Connection state change - Idle -> Calling

L2TPCM-24-1922: Notifying L2TP MIB {{1 14 24} 1922} new state 2

L2TPTRANS-24: sendAction: txWindow = 8, nextSend = 1

L2TPTRANS-24: _sendCtrl: nextS = 1, nextR = 3

L2TPTRANS-24: starting retry timer for 1000 milliseconds.

L2TPTRANS-24: State change - Idle -> TxWindowOpen

L2TPTRANS-24: processAck 2

L2TPTRANS-24: pulling seqNum 1 off of the queue

L2TPTRANS-24: State change - TxWindowOpen -> Idle

 

csmx-1/14> L2TPCM-24: Event = CallTimerExpired

?L2TPCM-24: Call timer expired; route 0 not found

L2TPCM-24: Event = SessionTimerExpired

L2TPCM-24: sending Hello

L2TPCM-24: starting Hello Timer for 60 seconds.

L2TPTRANS-24: sendAction: txWindow = 8, nextSend = 2

L2TPTRANS-24: _sendCtrl: nextS = 2, nextR = 3

L2TPTRANS-24: starting retry timer for 1000 milliseconds.

L2TPTRANS-24: State change - Idle -> TxWindowOpen

L2TPTRANS-24: processAck 2

L2TPTRANS-24: _receiveAction: peersNextS = 3, myNextR = 3

L2TPTRANS-24: _sendAck: nextS = 3, nextR = 4

L2TPCM-24: transportRxCallback from [172.16.133.1:61538/24] on VR0

L2TPCM-24: Event = RxStopCCN

L2TPCM-24: Parse StopCCN

L2TPCM-24: .. TunnelID = 7306 (0x1C8A)

L2TPCM-24: .. ResultCode = 2/6 (expecting reply; none received)

L2TPTRANS-24: TransportStop called.

L2TPCM-24-#1922: Disconnect call -- reason=730

L2TPCM-#1922: Connection state change - Calling -> <destroyed>

L2TPCM-24-1922: Notifying L2TP MIB {{1 14 24} 1922} new state 100

L2TPCM-24: Session state change - Up -> <destroyed>

L2TPCM-24: Notifying L2TP MIB {{ 1 14 24 } 0} new state 100

L2TPTRANS-24: State change - TxWindowOpen -> Closing

L2TPTRANS-24: _sendCtrl: nextS = 2, nextR = 4

2TPTRANS-24: starting retry timer for 1000 milliseconds.

L2TPTRANS-24: processAck 3

L2TPTRANS-24: pulling seqNum 2 off of the queue

L2TPTRANS-24: all data sent. Closing

--------------------------

 

профайл соединения:

admin> read connection sks-dialout

CONNECTION/sks-dialout read

admin> list

[in CONNECTION/sks-dialout]

station* = sks-dialout

active = yes

encapsulation-protocol = mpp

called-number-type = national

dial-number = ""

sub-address = ""

clid = ""

ip-options = { yes yes 10.33.144.12/32 0.0.0.0/0 1 60 120 no no 0 0.0.0.0

routi+

ipx-options = { no router-peer both both no 00:00:00:00 00:00:00:00 "" no

[ 0 0+

bridging-options = { 0 no }

session-options = { "" "" no no 120 no-idle 120 "" 0 disabled autobaud

1088000 +

telco-options = { originate-only no off 1 no no modem 0 "" "" no yes 0

virtual }

ppp-options = { no-ppp-auth none "" "" "" "" none 1524 no 600 600 no

cbcp-no-ca+

mp-options = { 1 1 2 no no }

mpp-options = { "" quadratic transmit 1 1 15 5 10 70 }

fr-options = { "" pvc 16 "" transparent-link no "" 16 "" }

tcp-clear-options = { "" 0 "" 0 "" 0 "" 0 no "" 256 20 }

ara-options = { "" 0 }

v120-options = { 7 3 1500 30000 256 }

answer-options = { }

x75-options = { 7 10 1000 1024 }

appletalk-options = { no "" 0 0 router-peer }

usrRad-options = { global 0.0.0.0 1646 "" 1 acct-base-10 }

calledNumber = ""

dhcp-options = { no 1 4 }

shared-prof = yes

framed-only = yes

tunnel-options = { dialout-profile l2tp-protocol 10 rip-off 172.16.133.1

"" 515+

vrouter = ""

atm-options = { aal5-llc 0 32 no "" none 1 { no { undefined "" { undefined

{ ""+

hdlc-nrm-options = { 2000 2 60000 5000 2 yes yes 255 }

visa2-options = { 10000 04 06 15 05 03 00:03:00:00 }

sdtn-packets-server = no

AT-string = ""

port-redirect-options = { none 0 0.0.0.0 }

 

dmin> list tunnel

[in CONNECTION/sks-dialout:tunnel-options]

profile-type = dialout-profile

tunneling-protocol = l2tp-protocol

max-tunnels = 10

atmp-ha-rip = rip-off

primary-tunnel-server = 172.16.133.1

secondary-tunnel-server = ""

udp-port = 5150

password = zhopa0zhopa

home-network-name = ""

client-auth-id = helix

server-auth-id = twister

vrouter = ""

assignment-id = ""

 

 

Вот такие пироги,

Я уж и так пробовал и этак, и в хвост и в гриву, мануалы курил,

и даже в саппорт alcatel-lucent обращался (неофициально конечно, потому как нахаляву ;) -

говорят - спецы по максам давно поувольнялись и только буржуины могут помочь...

Раньше был форум на lucent.ru, но после покупки алкателом его пристрелили... :(

 

Вобщем-то вопрос такой "решается ли это какими-то спец настройками или баг неустраним?"

 

Заранее спасибо.