[user_145]

Здравствуйте.

Столкнулся с такой проблемой.

Есть маршрутизатор циско 2811.

В него был вставлен модуль vic2-2fxo.

Вроде маршрутизатор видит

 

#show diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

Onboard VPN : v2.2.0

EEPROM contents at hardware discovery:

PCB Serial Number : FOC0950282L

Hardware Revision : 1.0

Top Assy. Part Number : 800-21849-02

Board Revision : B0

Deviation Number : 0

Fab Version : 03

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20051216

Chassis Serial Number : FCZ100170U4

Chassis MAC Address : 0015.fad8.21a8

MAC Address block size : 24

CLEI Code : CNMJ7N0BRA

Product (FRU) Number : CISCO2811

Part Number : 73-10258-03

Version Identifier : V02

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF C1 8B 46 4F 43 30 39 35 30 32 38 32 4C 40

0x10: 03 E7 41 01 00 C0 46 03 20 00 55 59 02 42 42 30

0x20: 88 00 00 00 00 02 03 03 00 81 00 00 00 00 04 00

0x30: 09 87 83 01 31 F5 10 C2 8B 46 43 5A 31 30 30 31

0x40: 37 30 55 34 C3 06 00 15 FA D8 21 A8 43 00 18 C6

0x50: 8A 43 4E 4D 4A 37 4E 30 42 52 41 CB 8F 43 49 53

0x60: 43 4F 32 38 31 31 20 20 20 20 20 20 82 49 28 12

0x70: 03 89 56 30 32 20 D9 02 40 C1 FF FF FF FF FF FF

 

WIC Slot 3:

2nd generation - FXO Voice daughter card (2 port)

Hardware Revision : 5.0

Top Assy. Part Number : 800-21597-03

Board Revision : B0

Deviation Number : 0-0

Fab Version : 04

PCB Serial Number : FOC121904R5

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VIC2-2FXO

Version Identifier : V02

CLEI Code : CNUIARTAAB

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 00 4D 41 05 00 C0 46 03 20 00 54 5D 03

0x10: 42 42 30 80 00 00 00 00 02 04 C1 8B 46 4F 43 31

0x20: 32 31 39 30 34 52 35 03 00 81 00 00 00 00 04 00

0x30: CB 89 56 49 43 32 2D 32 46 58 4F 89 56 30 32 20

0x40: C6 8A 43 4E 55 49 41 52 54 41 41 42 FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

 

#show version

 

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4(9)T, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright © 1986-2006 by Cisco Systems, Inc.

Compiled Fri 16-Jun-06 22:22 by prod_rel_team

 

Cisco 2811 (revision 53.51) with 772096K/14336K bytes of memory.

Processor board ID FCZ100170U4

2 FastEthernet interfaces

18 Serial interfaces

2 Channelized E1/PRI ports

1 Virtual Private Network (VPN) Module

2 Voice FXO interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

 

Configuration register is 0x3922

 

При попытке обнаружить в конфигурации

#show voice port

глухо.

при

#conf t

(config)#voice-port ?

<1-50> Voice interface slot

1- это установленный модуль с е1 50 - виртуальные порты CME

 

Судя с show diag - vic2-fxo должен опознаваться как voice-port 0/3/х.

 

В чем может быть проблема?

Как достучаться?

 

Заранее благодарен за помощь.