[Дмитрий К]

Возникла проблема с данным модемом

вышла из строя микросхема BCM5325EKQMG которая отвечает как я понял за 5 портовый свич.

Не мог бы кто-то подсказать распиновку этой микросхемы, думаю попробовать пробросить напрямик 1 порт Ethernet , например на первый 1 порт.Возможно ли такое.Микросхема свича уже удалена.

Роутер благополочно поднимает сессию суда по индикации и работает.статусные диоды работают.интересуют ноги микросхемы по которым сигнал идёт от процессора.

Заранее благодарен за ответ.

 

[Дмитрий К]

Лог прилагаю

 

 

CFE version 1.0.37-8.7 for BCM96338 (32bit,SP,BE)

Build Date: Wed Nov 28 18:21:10 CST 2007 (andy@BS5)(Revision: 44)

Copyright © 2000-2006 Broadcom Corporation.

 

Boot Address 0xbfc00000

 

Initializing Arena.

Initializing Devices.

Parallel flash device: name AM29LV160B, id 0x2249, size 2048KB

error on Ethernet Switch setup

Failed initializing enet hardware

CPU type 0x29010: 240MHz

Total memory: 8388608 bytes (8MB)

 

Total memory used by CFE: 0x80401000 - 0x80527660 (1205856)

Initialized Data: 0x8041CE80 - 0x8041EE90 (8208)

BSS Area: 0x8041EE90 - 0x80425660 (26576)

Local Heap: 0x80425660 - 0x80525660 (1048576)

Stack Area: 0x80525660 - 0x80527660 (8192)

Text (code) segment: 0x80401000 - 0x8041CE80 (114304)

Boot area (physical): 0x00528000 - 0x00568000

Relocation Factor: I:00000000 - D:00000000

 

Board IP address : 192.168.1.1:ffffff00

Host IP address : 192.168.1.100

Gateway IP address :

Run from flash/host (f/h) : f

Default host run file name : vmlinux

Default host flash file name : bcm963xx_fs_kernel

Boot delay (0-9 seconds) : 1

Board Id (0-10) : DSL-2540U

Number of MAC Addresses (1-32) : 10

Base MAC Address : **:**:**:**:**:**

PSI Size (1-64) KBytes : 24

 

Could not activate network interface 'eth0': CFE error -1

*** Press any key to stop auto run (1 seconds) ***

Auto run second count down: 0

Code Address: 0x80010000, Entry Address: 0x801ad018

Decompression OK!

Entry at 0x801ad018

Starting program at 0x801ad018

Linux version 2.6.8.1 (jenny@BS5) (gcc version 3.4.2) #1 Fri Jan 11 11:23:01 CST 2008

Parallel flash device: name AM29LV160B, id 0x2249, size 2048KB

DSL-2540U prom init

CPU revision is: 00029010

Determined physical RAM map:

memory: 007a0000 @ 00000000 (usable)

On node 0 totalpages: 1952

DMA zone: 1952 pages, LIFO batch:1

Normal zone: 0 pages, LIFO batch:1

HighMem zone: 0 pages, LIFO batch:1

Built 1 zonelists

Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200

brcm mips: enabling icache and dcache...

Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.

Primary data cache 8kB 2-way, linesize 16 bytes.

PID hash table entries: 32 (order 5: 256 bytes)

Using 120.000 MHz high precision timer.

Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)

Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)

Memory: 5808k/7808k available (1437k kernel code, 1980k reserved, 210k data, 68k init, 0k highmem)

Calibrating delay loop... 239.20 BogoMIPS

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Checking for 'wait' instruction... unavailable.

NET: Registered protocol family 16

Total Flash size: 2048K with 35 sectors

File system address: 0xbfc10100

Can't analyze prologue code at 80175dd4

Initializing Cryptographic API

PPP generic driver version 2.4.2

PPP Deflate Compression module registered

PPP BSD Compression module registered

MPPE/MPPC encryption/compression module registered

NET: Registered protocol family 24

Using noop io scheduler

bcm963xx_mtd driver v1.0

brcmboard: brcm_board_init entry

 

======= GPIO CONFIG_BCM96338 inited ========

Serial: BCM63XX driver $Revision: 3.00 $

ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX

NET: Registered protocol family 2

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 512 bind 1024)

Initializing IPsec netlink socket

NET: Registered protocol family 1

NET: Registered protocol family 17

NET: Registered protocol family 15

Ebtables v2.0 registered

NET: Registered protocol family 8

NET: Registered protocol family 20

802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>

All bugs added by David S. Miller <davem@redhat.com>

VFS: Mounted root (squashfs filesystem) readonly.

Freeing unused kernel memory: 68k freed

init started: BusyBox v1.00 (2008.01.11-03:24+0000) multi-call binary

Algorithmics/MIPS FPU Emulator v1.5

 

 

BusyBox v1.00 (2008.01.11-03:24+0000) Built-in shell (msh)

Enter 'help' for a list of built-in commands.

 

 

Loading drivers and kernel modules...

 

atmapi: module license 'Proprietary' taints kernel.

adsl: adsl_init entry

blaadd: blaa_detect entry

Broadcom BCMPROCFS v1.0 initialized

Broadcom BCM6338A2 Ethernet Network Device v0.3 Jan 11 2008 11:21:58

Config Ethernet Switch Through MDIO Pseudo PHY Interface

dgasp: kerSysRegisterDyingGaspHandler: eth0 registered

eth0: MAC Address: **:**:**:**:**:**

is not default cfg.

is not default cfg.

BcmAdsl_Initialize=0xC00673F8, g_pFnNotifyCallback=0xC007FC64

AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000

pSdramPHY=0xA07FFFF8, 0x0 0x80000

AdslCoreHwReset: AdslOemDataAddr = 0xA07FD3D4

AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000

dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered

ATM proc init !!!

ip_tables: © 2000-2002 Netfilter core team

ip_conntrack version 2.1 (61 buckets, 0 max) - 376 bytes per conntrack

ip_conntrack_pptp version 2.1 loaded

ip_nat_pptp version 2.0 loaded

insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_h323.ko': No such file or directory

insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_h323.ko': No such file or directory

ip_nat_ftp: Unknown symbol needs_ip_conntrack_ftp

insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_ftp.ko': Success (2): Success

ip_nat_sip: Unknown symbol sip_getpkt_type

ip_nat_sip: Unknown symbol ct_sip_hdrs

ip_nat_sip: Unknown symbol ct_sip_data

ip_nat_sip: Unknown symbol ct_sip_get_info

ip_nat_sip: Unknown symbol set_expected_rtp

insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_sip.ko': Success (2): Success

 

==> Bcm963xx Software Version: RU_DSL-2540U_1.00_01112008 <==

 

logread: not found

device eth0 entered promiscuous mode

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

BcmRfc2684_init interface is not up nas_0_1_32!

pvc2684ctl -a -v 0.1.32 -f &

pvc2684d: Interface "nas_0_1_32" created sucessfully

 

pvc2684d: Communicating over ATM 0.1.32, encapsulation: LLC

 

device eth0 left promiscuous mode

br0: port 1(eth0) entering disabled state

device eth0 entered promiscuous mode

br0: port 1(eth0) entering learning state

br0: topology change detected, propagating

br0: port 1(eth0) entering forwarding state

sntp: host not found

 

ioctl, p_name=diapd

 

*** diap wait system init 1 sec start

 

##############status LED blink now##################

no config file /etc/resolv.conf

*** diap wait system init 1 sec end

dft, wanIpAddress = , wanSubnetMask =

vpi = 1, vci = 32, conId = 1, portId = 0

nat = 1, firewall = 1

br0: port 1(eth0) entering disabled state

Plugin pppoe loaded.

RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3

Plugin pppoe called.