Дмитрий К Posted September 27, 2009 Posted September 27, 2009 Возникла проблема с данным модемом вышла из строя микросхема BCM5325EKQMG которая отвечает как я понял за 5 портовый свич. Не мог бы кто-то подсказать распиновку этой микросхемы, думаю попробовать пробросить напрямик 1 порт Ethernet , например на первый 1 порт.Возможно ли такое.Микросхема свича уже удалена. Роутер благополочно поднимает сессию суда по индикации и работает.статусные диоды работают.интересуют ноги микросхемы по которым сигнал идёт от процессора. Заранее благодарен за ответ. Вставить ник Quote
Дмитрий К Posted September 27, 2009 Author Posted September 27, 2009 Лог прилагаю CFE version 1.0.37-8.7 for BCM96338 (32bit,SP,BE) Build Date: Wed Nov 28 18:21:10 CST 2007 (andy@BS5)(Revision: 44) Copyright © 2000-2006 Broadcom Corporation. Boot Address 0xbfc00000 Initializing Arena. Initializing Devices. Parallel flash device: name AM29LV160B, id 0x2249, size 2048KB error on Ethernet Switch setup Failed initializing enet hardware CPU type 0x29010: 240MHz Total memory: 8388608 bytes (8MB) Total memory used by CFE: 0x80401000 - 0x80527660 (1205856) Initialized Data: 0x8041CE80 - 0x8041EE90 (8208) BSS Area: 0x8041EE90 - 0x80425660 (26576) Local Heap: 0x80425660 - 0x80525660 (1048576) Stack Area: 0x80525660 - 0x80527660 (8192) Text (code) segment: 0x80401000 - 0x8041CE80 (114304) Boot area (physical): 0x00528000 - 0x00568000 Relocation Factor: I:00000000 - D:00000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-10) : DSL-2540U Number of MAC Addresses (1-32) : 10 Base MAC Address : **:**:**:**:**:** PSI Size (1-64) KBytes : 24 Could not activate network interface 'eth0': CFE error -1 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Code Address: 0x80010000, Entry Address: 0x801ad018 Decompression OK! Entry at 0x801ad018 Starting program at 0x801ad018 Linux version 2.6.8.1 (jenny@BS5) (gcc version 3.4.2) #1 Fri Jan 11 11:23:01 CST 2008 Parallel flash device: name AM29LV160B, id 0x2249, size 2048KB DSL-2540U prom init CPU revision is: 00029010 Determined physical RAM map: memory: 007a0000 @ 00000000 (usable) On node 0 totalpages: 1952 DMA zone: 1952 pages, LIFO batch:1 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 brcm mips: enabling icache and dcache... Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 8kB 2-way, linesize 16 bytes. PID hash table entries: 32 (order 5: 256 bytes) Using 120.000 MHz high precision timer. Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) Memory: 5808k/7808k available (1437k kernel code, 1980k reserved, 210k data, 68k init, 0k highmem) Calibrating delay loop... 239.20 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction... unavailable. NET: Registered protocol family 16 Total Flash size: 2048K with 35 sectors File system address: 0xbfc10100 Can't analyze prologue code at 80175dd4 Initializing Cryptographic API PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered MPPE/MPPC encryption/compression module registered NET: Registered protocol family 24 Using noop io scheduler bcm963xx_mtd driver v1.0 brcmboard: brcm_board_init entry ======= GPIO CONFIG_BCM96338 inited ======== Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xfffe0300 (irq = 10) is a BCM63XX NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 512 bind 1024) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 68k freed init started: BusyBox v1.00 (2008.01.11-03:24+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.00 (2008.01.11-03:24+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... atmapi: module license 'Proprietary' taints kernel. adsl: adsl_init entry blaadd: blaa_detect entry Broadcom BCMPROCFS v1.0 initialized Broadcom BCM6338A2 Ethernet Network Device v0.3 Jan 11 2008 11:21:58 Config Ethernet Switch Through MDIO Pseudo PHY Interface dgasp: kerSysRegisterDyingGaspHandler: eth0 registered eth0: MAC Address: **:**:**:**:**:** is not default cfg. is not default cfg. BcmAdsl_Initialize=0xC00673F8, g_pFnNotifyCallback=0xC007FC64 AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000 pSdramPHY=0xA07FFFF8, 0x0 0x80000 AdslCoreHwReset: AdslOemDataAddr = 0xA07FD3D4 AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered ATM proc init !!! ip_tables: © 2000-2002 Netfilter core team ip_conntrack version 2.1 (61 buckets, 0 max) - 376 bytes per conntrack ip_conntrack_pptp version 2.1 loaded ip_nat_pptp version 2.0 loaded insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_h323.ko': No such file or directory insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_h323.ko': No such file or directory ip_nat_ftp: Unknown symbol needs_ip_conntrack_ftp insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_ftp.ko': Success (2): Success ip_nat_sip: Unknown symbol sip_getpkt_type ip_nat_sip: Unknown symbol ct_sip_hdrs ip_nat_sip: Unknown symbol ct_sip_data ip_nat_sip: Unknown symbol ct_sip_get_info ip_nat_sip: Unknown symbol set_expected_rtp insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_sip.ko': Success (2): Success ==> Bcm963xx Software Version: RU_DSL-2540U_1.00_01112008 <== logread: not found device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state BcmRfc2684_init interface is not up nas_0_1_32! pvc2684ctl -a -v 0.1.32 -f & pvc2684d: Interface "nas_0_1_32" created sucessfully pvc2684d: Communicating over ATM 0.1.32, encapsulation: LLC device eth0 left promiscuous mode br0: port 1(eth0) entering disabled state device eth0 entered promiscuous mode br0: port 1(eth0) entering learning state br0: topology change detected, propagating br0: port 1(eth0) entering forwarding state sntp: host not found ioctl, p_name=diapd *** diap wait system init 1 sec start ##############status LED blink now################## no config file /etc/resolv.conf *** diap wait system init 1 sec end dft, wanIpAddress = , wanSubnetMask = vpi = 1, vci = 32, conId = 1, portId = 0 nat = 1, firewall = 1 br0: port 1(eth0) entering disabled state Plugin pppoe loaded. RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3 Plugin pppoe called. Вставить ник Quote
.png.5d2afa2996cc6a85d0f2c09b92dd0a28.png)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.