Firmware для HP 5406zl

[asduks]

Здравствуйте.

Может есть у кого свежие прошивки для данного коммутатора J8697A? В данный момент установлена 15.04

Edited January 9, 2025 by asduks

[tt128]

Есть K_15_16_0021

 

 

 

Edited January 9, 2025 by tt128

[asduks]

Хотя бы для начала, выложите куда-нибудь пожалуйста. Там дальше обновления могут быть через промежуточные.

[tt128]

https://drive.google.com/file/d/1mLF8nbgays_Tgkad5RWnsy0UmK1UgcgV/view?usp=sharing

 

[asduks]

Забрал, премного благодарен

[jffulcrum]

  

Скрытый текст

CAUTION: If you are updating from a software version that is susceptible to the 'hang' problem to this software, HP recommends that software updates and reboots occur when there can be someone onsite to power cycle any switch that does not recover spontaneously after reload. These software versions are susceptible: K.15.01.xxxx - K.15.05.xxxx K.15.06.0006 - K.15.06.0014 K.15.07.0002 - K.15.07.0005 K.15.08.0007 K.15.04.0007m - K.15.04.0010m +++++++++++++++++++++++++++++++++++++++++++++++++ Digital Signature Note: Beginning with K.15.09, the switch software includes a digital signature. However, if this software is downloaded by an earlier software version that does not understand digital signatures, the earlier software will remove the digital signature before storing the new software in flash. In order to have digitally-signed software in the switch, you must boot the switch into K.15.09 or later software, and then re-download the K.15.09 or later software into the same flash it is already in (primary or secondary). Because the switch is now using a software version that understands digital signatures, the signature is not stripped during the download. Use the verify signature flash command to see if the software has a digital signature. After entering the command, if the software is digitally signed the switch does nothing for approximately 30 seconds, then responds. If the software is not digitally signed, the switch responds in approximately 10 seconds. +++++++++++++++++++++++++++++++++++++++++++++++++ IMPORTANT: If your switch is running a software version earlier than K.15, your BootROM will be updated when you upload K.15.15.0009 software to your switch. All switches must be running a BootROM version of K.12.17 or newer in order to load K.15 software. Do not interrupt power to the switch during this important update! A successful update to K.15 software may require multiple steps, depending on your current software and BootROM levels. Please see details in the table below. If your software version is: Your next step should be: K.11.11 through K.12.29(BootROM K.11.00 - K.11.03) Update and reload into software version K.12.31 or K.12.62 K.12.31 through K.13.55(BootROM K.12.12 - K.12.14) Update and reload into software version K.13.58 or K.13.68 K.13.58 or newer(BootROM K.12.17 or newer;use 'show flash' command) Update directly into software version K.15.15.0009 (BootROM K.15.30)

15.09 см. личку

[No_name]

Скрытый текст

Switch 5406# sh fl
Image             Size (bytes) Date     Version
----------------- ------------ -------- --------------
Primary Image    :    15733602 05/12/17 K.16.02.0019
Secondary Image  :    16740639 01/30/15 K.15.16.0006

Boot ROM Version
----------------
Primary Boot ROM Version   : K.15.30

Default Boot Image   : Primary

 

------------------------------------------------------

Есть и последняя К_16.02.0036

 

[asduks]

jffulcrum - благодарю за информацию и прошивку

 

No_name - можете поделиться?

Edited January 10, 2025 by asduks

[No_name]

Скрытый текст

https://disk.yandex.ru/d/fSkS9Hhe2xJ6PQ

 

[asduks]

Благодарю, забрал