Ulugbek1404 Posted October 18, 2021 Posted October 18, 2021 (edited) Power Inline Status: On Power Available: 185 W Power Used: 18 W Power Remaining: 167 W Min Voltage: 44 V Max Voltage: 57 V Police: Off Legacy: Off Disconnect: Ac Mode: Signal HW Version: 00 SW Version: 02.1.1 SNR-S2982G-24T-POE Device, Compiled on Sep 29 10:52:50 2018 sysLocation Building 57/2,Predelnaya st, Ekaterinburg, Russia CPU Mac f8:f0:82:7b:7d:ba Vlan MAC f8:f0:82:7b:7d:b9 SoftWare Version 7.0.3.5(R0241.0279) BootRom Version 7.2.35 HardWare Version 1.0.1 CPLD Version N/A Serial No.:SW078610K511000233 Copyright (C) 2018 NAG LLC All rights reserved Last reboot is cold reset. Uptime is 0 weeks, 6 days, 23 hours, 1 minutes 653 %Oct 18 12:33:21 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD is detected and powered! 652 %Oct 18 12:32:45 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/3, PD is detected and powered! 651 %Oct 18 12:32:34 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/3, PD is not powered! 650 %Oct 18 12:32:18 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD is not powered! 649 %Oct 18 12:09:01 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD is detected and powered! 648 %Oct 18 12:06:59 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD is not powered! 647 %Oct 18 11:51:04 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD is detected and powered! 646 %Oct 18 11:51:01 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD oper change to :4 645 %Oct 18 11:29:00 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/11, PD is detected and powered! 644 %Oct 18 11:28:57 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/9, PD is not powered! 643 %Oct 18 11:28:09 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/9, PD is detected and powered! 642 %Oct 18 11:28:01 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/9, PD is not powered! 641 %Oct 18 11:25:12 2021 <critical> MODULE_POE[tPoeStatus]:%LINK-3-POE: Interface Ethernet1/0/9, PD is detected and powered! 1/0/1 DOWN/DOWN auto auto 15 G-TX 1/0/2 UP/UP a-1G a-FULL 15 G-TX 1/0/3 UP/UP a-100M a-FULL 222 G-TX phone 1/0/4 UP/UP a-10M a-FULL 15 G-TX 1/0/5 UP/UP a-1G a-FULL 15 G-TX 1/0/6 UP/UP a-1G a-FULL 15 G-TX 1/0/7 UP/UP a-1G a-FULL 15 G-TX 1/0/8 UP/UP a-1G a-FULL 15 G-TX 1/0/9 DOWN/DOWN auto auto 222 G-TX phone 1/0/10 UP/UP a-10M a-FULL 15 G-TX 1/0/11 DOWN/DOWN f-100M f-half 222 G-TX 1825 %Oct 18 12:37:47 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1824 %Oct 18 12:37:46 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1823 %Oct 18 12:37:45 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1822 %Oct 18 12:37:43 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1821 %Oct 18 12:37:42 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1820 %Oct 18 12:37:40 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1819 %Oct 18 12:37:35 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1818 %Oct 18 12:37:34 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1817 %Oct 18 12:37:23 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1816 %Oct 18 12:37:22 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1815 %Oct 18 12:37:20 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1814 %Oct 18 12:37:19 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1813 %Oct 18 12:37:14 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1812 %Oct 18 12:37:13 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1811 %Oct 18 12:37:07 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN 1810 %Oct 18 12:37:07 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to UP 1809 %Oct 18 12:37:04 2021 <warnings> MODULE_PORT[tphyDaemon]:%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/0/11, changed state to DOWN Interface Ethernet1/0/11 speed-duplex force100-half switchport access vlan 222 loopback-detection specified-vlan 15 loopback-detection control shutdown Interface Ethernet1/0/3 speed-duplex auto description phone 3201 rate-violation broadcast 100 switchport access vlan 222 loopback-detection specified-vlan 15 loopback-detection control shutdown sh int eth 1/0/3 Interface brief: Ethernet1/0/3 is up, line protocol is up Ethernet1/0/3 is layer 2 port, alias name is phone 3201, index is 3 Hardware is Gigabit-TX, address is f8-f0-82-7b-7d-ba PVID is 222 MTU 1500 bytes, BW 100000 Kbit Time since last status change:0w-0d-3h-15m-19s (11719 seconds) Encapsulation ARPA, Loopback not set Auto-duplex: Negotiation full-duplex, Auto-speed: Negotiation 100M bits FlowControl is off, MDI type is auto Statistics: 5 minute input rate 35 bits/sec, 0 packets/sec 5 minute output rate 771 bits/sec, 1 packets/sec The last 5 second input rate 0 bits/sec, 0 packets/sec The last 5 second output rate 445 bits/sec, 1 packets/sec Input packets statistics: 321148 input packets, 69362213 bytes, 0 no buffer 282957 unicast packets, 37731 multicast packets, 460 broadcast packets 0 input errors, 0 CRC, 0 frame alignment, 0 overrun, 0 ignored, 0 abort, 0 length error, 0 undersize 0 jabber, 0 fragments, 0 pause frame Output packets statistics: 1075400 output packets, 128224505 bytes, 0 underruns 534594 unicast packets, 298668 multicast packets, 242138 broadcast packets 0 output errors, 0 collisions, 0 late collisions, 0 pause frame sh int eth 1/0/11 Interface brief: Ethernet1/0/11 is down, line protocol is down Ethernet1/0/11 is layer 2 port, alias name is (null), index is 11 Hardware is Gigabit-TX, address is f8-f0-82-7b-7d-ba PVID is 222 MTU 1500 bytes, BW 10000 Kbit Time since last status change:0w-0d-3h-10m-45s (11445 seconds) Encapsulation ARPA, Loopback not set Force half-duplex, Force 100M FlowControl is off, MDI type is auto Statistics: 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec The last 5 second input rate 0 bits/sec, 0 packets/sec The last 5 second output rate 0 bits/sec, 0 packets/sec Input packets statistics: 6 input packets, 733 bytes, 6 no buffer 0 unicast packets, 0 multicast packets, 0 broadcast packets 6 input errors, 2 CRC, 0 frame alignment, 0 overrun, 0 ignored, 0 abort, 0 length error, 0 undersize 0 jabber, 4 fragments, 0 pause frame Output packets statistics: 563 output packets, 61369 bytes, 0 underruns 128 unicast packets, 323 multicast packets, 112 broadcast packets 0 output errors, 0 collisions, 0 late collisions, 0 pause frame У меня проблема с POE подключаем телефон Grandstream GXP1625 к порту int eth 1/0/9 и телефон сам включается и не определяется по мак адресу. Переключили на другой порт int eth 1/0/11 телефон также питается от POE но к коммутатору мак не видно. Поменяли порти с таким же моделью телефона то есть на int eth 1/0/3 стоял и работал телефон а на int eth 1/0/11 стоял но не работал телефон поменяли и убедился что тот телефон который не работал заработал на этом порту то есть проблема не в телефонах Edited October 18, 2021 by Ulugbek1404 добавил новые информации Вставить ник Quote
passer Posted October 18, 2021 Posted October 18, 2021 А зачем такие вот извраты на порту? speed-duplex force100-half Надо задать режим, так не обязательно ломать автосогласование: speed-duplex auto 10 Вставить ник Quote
Aleksey Sonkin Posted October 18, 2021 Posted October 18, 2021 @passer + к вышесказанному, также обновите версию ПО до последней рекомендуемой. Если проблема не решится - обратитесь на support.nag.ru, приложив подробное последовательное описание проблемы с логами. Вставить ник Quote
Ulugbek1404 Posted October 19, 2021 Author Posted October 19, 2021 22 часа назад, Aleksey Sonkin сказал: @passer + к вышесказанному, также обновите версию ПО до последней рекомендуемой. Если проблема не решится - обратитесь на support.nag.ru, приложив подробное последовательное описание проблемы с логами. Спасибо за ответ 23 часа назад, passer сказал: А зачем такие вот извраты на порту? speed-duplex force100-half Надо задать режим, так не обязательно ломать автосогласование: speed-duplex auto 10 я проста попробовал другие решение но потом вернул обратно на авто Вставить ник Quote
.png.5d2afa2996cc6a85d0f2c09b92dd0a28.png)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.