[carver]

есть несколько Ericsson mini-link cn510, инженеры не могут на них попасть.

из портов, доступен только telnet, на котором какая-то ругань(лог ниже).
...говорят ранее стояли вторыми в XPIC.

кнопку сброса держал, но явно дело не в ней.
думаю проблема в логине cli, и его cli_shell,
скорее всего CLI логин завязан на какой-то /var, что слетел.
наверное и остальное не стартует для CRAFT Shell

сталкивался с таким в ATHEME DR5000, там в старых прошивках,
тоже забывали запускать fsck при старте.
но для bash - admin/root - "паролей/ключей" нет, как и нет саппорта от производителя.

может кто сталкивался, как "обнулить/сбросить" и получить доступ ?

 

спасибо.
 

Linux 2.6.18_pro500-R5G04 ((none)) (ttyp0)

(none) login: root
Password: 

Login incorrect
(none) login: admin
Password: 

Login incorrect
(none) login: cli
No directory, logging in with HOME=/
CLI may be busy ...
[aprint] Failed to get aprint shared memory, errno=13
[aprint] aprint shared mem / semaphore preparation failed
[aprint] Failed blocking signals / locking aprint semaphore!

SYS:../platform/cmo/cm/src/cli_relay-main.c(61)(FLASH:WARM): Error(111): Sorry, can't connect!

[aprint] Failed blocking signals / locking aprint semaphore!
[aprint] Message not written to flash: WARM:cli_relay:Error(111): Sorry, can't connect!

 

Изменено 23 августа, 2021 пользователем carver

[carver]

все еще не решил, 
кто-то может знает, как активировать/попасть в это PBIST меню ?
 

CN510R2 PBIST
-------------
 D   Display Revision ID     
 S   Short RAM Test          
 L   Long RAM Test           
 F   Firmware Checksum Test  
 M   Flash (NOR/NAND) Test   

 

Скрытый текст

Started NPU...
NPU Load Modules ------------------------
   Boot:  CN510R2 CXC1731963_2-R1A17
          Build Date: Apr 22 2013 - 13:17:52(xrserhe)
   PBIST: CN510R2 CXC1731879_2-R1B02
          Build Date: May 15 2014 - 11:14:19(etamjuh)
   Device tree     : CXC 173 5073/1 20130521
   Kernel image 0  : CXP 902 0510/2 R7B126 20160224 170722
   Kernel image 1  : CXP 902 0510/2 R2K12 20150319 175853
-----------------------------------------

Started NPU...


CN510R2 PBIST
-------------
 D   Display Revision ID     
 S   Short RAM Test          
 L   Long RAM Test           
 F   Firmware Checksum Test  
 M   Flash (NOR/NAND) Test   
 U   User IO Test            
 X   Front Panel Test        
 I   SPI controller Test     
 P   Power Management Test   
 T   Temperature Sensor Test 
 N   Ethernet Test           
 Q   LIU acknowledge Test    
 C   Load and test FPGA      
 K   USB connection test     
 R   Real Time Clock Test    
 E   E1 traffic test         
 Y   Test HARAKIRI#          
 V   Test Board Reset        
 B   OCXO Test               
 O   SmartCard Commands      
 G   Erase Image             
 J   Start U-BOOT
 H   Load files
 *   Autoload programs       

PBIST> H

 Load via TFTP (auto mode)
 /  Toggle edit/auto mode
 0  Change TFTP settings
 1  PBIST
 2  Script
 3  BOOT
 4  IMAGE0
 5  IMAGE1
 6  U-BOOT
 7  FDT
 8  FPGA
 9  Exit

 

 

 

ну и лог с консоли, для гугла

 

Скрытый текст

Started NPU...
NPU Load Modules ------------------------
   Boot:  CN510R2 CXC1731963_2-R1A17
          Build Date: Apr 22 2013 - 13:17:52(xrserhe)
   PBIST: CN510R2 CXC1731879_2-R1B02
          Build Date: May 15 2014 - 11:14:19(etamjuh)
   Device tree     : CXC 173 5073/1 20130521
   Kernel image 0  : CXP 902 0510/2 R7B126 20160224 170722
   Kernel image 1  : CXP 902 0510/2 R2K12 20150319 175853
-----------------------------------------
Start kernel from Active bank: image 0  now...

[    0.000000] Using MPC832x based NPU/CN board machine description
[    0.000000] Linux version 3.10.75-R1B02-rt80 (mwtnmgr@eselnlx1738) (gcc version 4.7.0 (MontaVista Linux G++ 4.7-150727093217) ) #1 PREEMPT RT Thu Jan 28 15:47:52 CET 2016
setup_arch: bootmem
mpc832x_npu_setup_arch()
arch: exit
[    0.000000] bootconsole [udbg0] enabled
[    0.000000] MPC832x CN210 R2 (MPC8323ERDB based)
[    0.000000] NPU West PCI bus: controller = c03dc000, address = [0x80000000 - 0x9fffffff], buses = [0x00 - 0x0f]
[    0.000000] Configuring USB pins
[    0.000000] HAS USB returned 0
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x00000000-0x07ffffff]
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x07ffffff]
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: root=/dev/mtdblock1 rootfstype=jffs2 ro console=ttyS0,115200
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Sorting __ex_table...
[    0.000000] Memory: 125904k/131072k available (3608k kernel code, 5168k reserved, 196k data, 145k bss, 144k init)
[    0.000000] Kernel virtual memory layout:
[    0.000000]   * 0xfffdf000..0xfffff000  : fixmap
[    0.000000]   * 0xfdef9000..0xfe000000  : early ioremap
[    0.000000]   * 0xc9000000..0xfdef9000  : vmalloc & ioremap
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:512 nr_irqs:512 16
[    0.000000] IPIC (128 IRQ sources) at c9000700
[    0.000000] clocksource: timebase mult[10000000] shift[23] registered
[    0.000155] pid_max: default: 32768 minimum: 501
[    0.000472] Mount-cache hash table entries: 512
[    0.009324] devtmpfs: initialized
[    0.159928] NET: Registered protocol family 16
             
[    0.170253] uc_loader:  UC loader started mpc83xx_ucode_init
[    0.175920] uc_loader:  QE REV ce100001, core 80670011 80840011 fdefe000
[    0.182517] uc_loader:  LoadUCodePatch UC size 4084
[    0.187627] uc_loader:  LoadUCodePatch UC compare done.
[    0.192740] uc_loader:  LoadUCodePatch REG fdf02100=c00003e5
[    0.198314] uc_loader:  LoadUCodePatch REG fdf02104=c0000518
[    0.203888] uc_loader:  LoadUCodePatch REG fdf02108=0
[    0.208862] uc_loader:  LoadUCodePatch REG fdf0210c=0
[    0.213836] uc_loader:  LoadUCodePatch REG fdf02110=0
[    0.218810] uc_loader:  LoadUCodePatch REG fdf02114=0
[    0.223784] uc_loader:  LoadUCodePatch REG fdf02118=0
[    0.228759] uc_loader:  LoadUCodePatch REG fdf021f0=20800000
[    0.235686] PCI: Probing PCI hardware
[    0.239256] PCI: I/O resource not set for host bridge /localbus@ff405000/pci-west@0xf0040000 (domain 0)
[    0.249241] PCI host bridge to bus 0000:00
[    0.253262] pci_bus 0000:00: root bus resource [mem 0x80000000-0x9fffffff]
[    0.260060] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.302504] bio: create slab <bio-0> at 0
[    0.314351] Switching to clocksource timebase
[    0.327298] NET: Registered protocol family 2
[    0.333991] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[    0.341132] TCP bind hash table entries: 1024 (order: 2, 24576 bytes)
[    0.347635] TCP: Hash tables configured (established 1024 bind 1024)
[    0.354036] TCP: reno registered
[    0.357209] UDP hash table entries: 256 (order: 2, 16384 bytes)
[    0.363167] UDP-Lite hash table entries: 256 (order: 2, 16384 bytes)
[    0.370116] NET: Registered protocol family 1
[    0.375404] RPC: Registered named UNIX socket transport module.
[    0.381204] RPC: Registered udp transport module.
[    0.385834] RPC: Registered tcp transport module.
[    0.390466] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.400695] mpc8xxx_wdt: WDT driver for MPC8xxx initialized. mode:reset timeout=65535 (8589 jiffies, 34 seconds)
[    0.422417] Seems like legacy loclabus, skipping elbc init steps!
[    0.513806] jffs2: version 2.2. (NAND) (SUMMARY)  B) 2001-2006 Red Hat, Inc.
[    0.528516] msgmni has been set to 245
[    0.532360] io scheduler noop registered (default)
[    0.563094] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.574613] serial8250.0: ttyS0 at MMIO 0xff404500 (irq = 16) is a 16550A
[    0.581429] console [ttyS0] enabled, bootconsole disabled
[    0.581429] console [ttyS0] enabled, bootconsole disabled
[    0.593892] serial8250.0: ttyS1 at MMIO 0xff404600 (irq = 17) is a 16550A
[    0.603775] Freescale QUICC Engine UART device driver
[    0.608976] ucc-uart: could not register UART driver
[    0.617250] Trying ONFI probe in 16 bits mode, aborting !
[    0.622871] ONDIE ECC detected
[    0.625976] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xca (Micron NAND 256MiB 3,3V 16-bit), 256MiB, page size: 2048, OOB size: 64
[    0.638069] Scanning device for bad blocks
[    0.940219] Found name: 0x70000000.flash, size: 0x10000000, erasesize: 0x20000, writesize: 0x800, oobsize: 0x40.
[    0.950468] boot_info = 0x000000e3
[    0.954223] rootfsoffset from drb is 0x3dd000
[    0.958626] read kernsize: 0x3dc230
[    0.962150] FLASH WARN: rootFSoffset updated
[    0.966476] Root FS offset is 0x003dc23c bytes = 7ba pages = 1f blocks
[    0.974284] Creating 4 MTD partitions on "0x70000000.flash":
[    0.980049] 0x000000000000-0x0000003e0000 : "Header/Kernel (R/O)"
[    0.989896] 0x0000003e0000-0x000004000000 : "Root Disk (R/O)"
[    0.999498] 0x000004000000-0x000008000000 : "Root Disk (R/W)"
[    1.009208] 0x000008000000-0x000010000000 : "Util (R/W)"
[    1.019982] NPU-NOR:0x00800000 at 0x60000000
[    1.025275] NOR flash on NPUs (8MB): Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x000c01
[    1.036427] Amd/Fujitsu Extended Query Table at 0x0040
[    1.041635]   Amd/Fujitsu Extended Query version 1.3.
[    1.046754] number of CFI chips: 1
[    1.051550] Creating 4 MTD partitions on "NOR flash on NPUs (8MB)":
[    1.057896] 0x000000000000-0x000000200000 : "Boot/PBIST (R/O)"
[    1.067386] 0x000000200000-0x000000400000 : "U-Boot/Env (R/O)"
[    1.077000] 0x000000400000-0x000000600000 : "Spare (R/O)"
[    1.086186] 0x000000600000-0x000000800000 : "Crash (R/W)"
[    1.097982] libphy: Fixed MDIO Bus: probed
[    1.105010] ucc_geth_driver: QE UCC Gigabit Ethernet Controller
[    1.111360] ucc_geth_driver: UCC2 at 0xff503000 (irq = 34)
[    1.119456] PPP generic driver version 2.4.2
[    1.123848] ML-PPP with MiniLink TN adaptation
[    1.129623] PPP Deflate Compression module registered
[    1.135352] qe_udc_probe
[    1.137959] soc_type: 1
[    1.141615] fsl_qe_udc ff5006c0.usb: QE USB controller initialized as device
[    1.149404] g_ether gadget: using random self ethernet address
[    1.155424] g_ether gadget: using random host ethernet address
[    1.163196] usb0: MAC 9a:43:50:46:83:84
[    1.167164] usb0: HOST MAC 6e:30:72:97:86:e8
[    1.171657] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[    1.178333] g_ether gadget: g_ether ready
[    1.182494] fsl_qe_udc ff5006c0.usb: fsl_qe_udc bind to driver g_ether
[    1.192154] mpc-i2c ff403000.i2c: timeout 1000000 us
[    1.200924] TCP: cubic registered
[    1.208699] NET: Registered protocol family 10
[    1.217118] NET: Registered protocol family 17
[    1.226577] TCP: TFO aes cipher alloc error: -2
[    8.621854] jffs2: notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    8.638251] VFS: Mounted root (jffs2 filesystem) readonly on device 31:1.
[    8.647699] devtmpfs: mounted
[    8.652142] Freeing unused kernel memory: 144K (c0362000 - c0386000)
INIT: version 2.88 booting
Starting Bootlog daemon: bootlogd.
Setting up USB DHCP
[   12.214504] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.280935] nf_conntrack version 0.5.0 (1969 buckets, 7876 max)
[   12.444369] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
Configuring network interfaces... done.
Wed Feb 17 15:29:00 UTC 2016
Starting syslog-ng:.
Starting flogd:   [ OK ]
Starting segfaultd:   [ OK ]
INIT: Entering runlevel: 3
Starting BDMOD: [  OK ]
Starting CHKERNEL: [  OK ]
Starting CH:   [ OK ]
Starting KUTIL: [  OK ]
Starting SPI-DRV: [  OK ]
BACKPLANE=CN
NPUTYPE=CN510R2
NPUROLEPROTECTION=PROTECTIVE
NPUROLEBUS=SLAVE
NPURAM=126048 kbytes
KERNEL_VERSION=3.1
Starting FPGA_LOAD: NPUTYPE=CN510R2
Starting FPGA Loader TDM CN510R2 [  OK ]
[  OK ]
Starting ntpd: done
Resetting xinetd
Restarting internet superserver: xinetd.
Config   TFTP: [ OK ]
Starting protection driver:  [ OK ]
Removing start and kill scripts cp: can't stat '*xinetd.*': No such file or directory
cp: can't stat '*ipr.*': No such file or directory
cp: can't stat '*hotfix2.*': No such file or directory
cp: can't stat '*tnipc_dp-ip-client.*': No such file or directory
cp: can't stat '*hotfix2.*': No such file or directory
cp: can't stat '*tnipc_dp-ip-client.*': No such file or directory
  [ OK ]
Installing the RTC device driver: [ OK ]
System time: Mon Jan  3 23:57:31 2000  0.000000 seconds
Starting User I/O module: [ OK ]
Starting PS:   [ OK ]
MLHC is supported by NERD on this NPUTYPE: CN510R2
This NPUTYPE (CN510R2) can not handle MLHC in MMUs
Starting MLHCH: PPC_ipclib::Ipc_receive: No such file or directory
 [ OK ]
Starting PLH:      [ OK ]
Config   TFTP:     [ OK ]
Reseting xinetd
Restarting internet superserver: xinetd.
Loading  SPI_DD: (already installed)   [ OK ]
Starting WDKICKER: [ OK ]
Protection mode is 1+1 Slave.
TnIpc started:  TnIpc: [ OK ] Npudd: [ OK ] ip-relay: [ dont start here ]
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
Starting ip-relay:     [ OK ]
Starting PADS: PADS: Banks: /dev/mtd0 (active), /dev/mtd2 (passive) 
    [ OK ]
Starting SPI IP Client:[ OK ]
Loading  EOP: [ OK ]


   ///\ __///\                            /\\\__ /\\\
  ///\\(  )/\\\      D'Bug Interface     ///\(  )//\\\
 ///     OO  \\\                        ///  OO     \\\

     Line: console     Time: 23:57:37     User(s): 0 

freescale-83xx login: 

   ///\ __///\                            /\\\__ /\\\
  ///\\(  )/\\\      D'Bug Interface     ///\(  )//\\\
 ///     OO  \\\                        ///  OO     \\\

     Line: console     Time: 23:58:12     User(s): 0 

freescale-83xx login: cli
Password: 

Login incorrect
freescale-83xx login:

 

Изменено 23 августа, 2021 пользователем carver

[carver]

решил.

в eeprom было записано  0x01 - режим "SLAVE".
сменил на "0x00" - MASTER или сразу на 0x02 "STANDALONE" - доступ появился.
 

может в кого еще есть прошивка на CN510 ? у меня есть такие

CXP9020510_102_R2B11    CXP 902 0510/102    R2B11    (20140422)    // 102 HW model ???
CXP9020510_102_R5B114    CXP 902 0510/102    R5B114    (20150313)    // 102 HW model ???
CXP9020510_1_R4C03    CXP 902 0510/1        R4C03    (20120116)    // no RF FW
CXP9020510_1_R4E06    CXP 902 0510/1        R4E06    (20120516)    // no RF FW
CXP9020510_2_R2B11    CXP 902 0510/2        R2B11    (20140422)    // no RF FW
CXP9020510_2_R2F08    CXP 902 0510/2        R2F08    (20140919)
CXP9020510_2_R2H02    CXP 902 0510/2        R2H02    (20150209)
CXP9020510_2_R2K12    CXP 902 0510/2        R2K12    (20150319)
CXP9020510_2_R7B126    CXP 902 0510/2        R7B126    (20160224)
 

но еще интересует CXP9020510_1_R4H01 CXP 902 0510/1  R4H01