Jump to content
Калькуляторы

Помогите собрать аналоговый модемный пул v90/56k

@Mis np60 да как цифровые модемы в самый раз

Не забывайте вре мя от времени обращаться к каноническому посту, где есть все варианты работающих конфигураций на циско

Share this post


Link to post
Share on other sites

Quote

2. [USR COURIER/...]->(2811:[VIC3-4FXS]->[VWIC-1MFT-E1]->[NM-2CE1T1-PRI]->[PVDM2-12DM]) (возьму в арт объект т.к. это вариант все-в-одном)

Доброго дня.

В этом сетапе VWIC-1MFT-E1 какой версии, FRU какой? VWIC2-1MFT-G703 - 1-Port RJ-48 Multiflex Trunk - T1/E1 & G.703 Product (FRU) Number: VWIC2-1MFT-G703  подойдёт?

IOS spservicesk9-mz.151-4.M10 хватит ?

кросс-кабель [VWIC-1MFT-E1]<->[NM-2CE1T1-PRI] обычный 12 45 --- 45 12 ?

Edited by mkmv

Share this post


Link to post
Share on other sites

Я побаловался, пул разобрал и аккуратно сложил в бытовку, так что по версии ничего не скажу.  G.703 подойдет, почему бы и нет. IOS какой-то из adventerprise-12.4T. Кросс-кабель обычный.

Share this post


Link to post
Share on other sites

День добрый! Теперь настала моя очередь проводить археологические работы и потребовалась помощь зала.

 

Схема получилась такой: (абонент с телефоном и модемом) - Panasonic NCP500 - Е1 - Cisco 5350 (60NP) - сеть

 

Путем честного копипастинга отсюда мне удалось завести коннект с модема. Дальше коннекта дело пока не пошло, ибо почитал спеки, что 60NP умеет и в голос и возжелал онное.

 

Курю старые маны от циски, но пока так и не смог понять, как сделать так, чтобы несколько портов в 60np отвечали как голос, а несколько - как модемы. Универсальные же. Хелпа! Может, у кого завалялось в архивах примеры конфигов и (вообще будет шикарно) воис-паки с скриптами?

 

Share this post


Link to post
Share on other sites

Добрый день, уважаемые форумчане! 

Есть ли у кого то на продажу оборудование для организации подобных экспериментов? 

У меня пока появилась  только 2811. Все остальное готов приобрести за вменяемую цену.  Естессвенно первым делом полез на авито, там цена модуля nm30-dm около 30000р, по моему это слишком. 

Share this post


Link to post
Share on other sites

Оно все безсмысленно дорогое, да. Мне показалось дешевле взять атс с ip (panasonic ncp500) + (e1 плату к ней) + бандл cisco 5350 с e1 и 60 модемами. На авито все скопом можно за 20 тр найти (как минимум было)

Share this post


Link to post
Share on other sites

Всем здравствуйте. Удалось заполучить на авито panasonic kx ncp 1000 с платой е1  канала.  Оборудование б/у, пока разобрался как к ней пароль подобрать, как посмотреть ip адрес для подключения (измененный с дефолтного на другой прошлыми хозяевами) , как установить программу для подключения выбрав нужный регион, посмотреть лицензии.. И ничего толком не поняв. Пишу поинтересоваться, если ли у кого то подобная атс? У меня несколько вопросов по настройке и проливке лицензий (надеюсь получится найти лицензии за вменяемые деньги) . И да, еще у меня появились несколько cisco 3745 , 2621 , 2651 (скупил всë что нашел самое дешевое, железки о которых шла речь в этой ветке). 

Share this post


Link to post
Share on other sites

Перечитал всë по Вашей ссылке, интересно, спасибо. Найдя крохи инфы в инете я сделал всë тоже самое что и Вы, кроме генерации серийного номера для программы управления атс, в ходе установки вместо ввода серийника нажал skip, не знаю на сколько это критично, но к атс я в итоге смог подключиться. Далее стадия конфигурирования номеров, тут пока не успел разобраться как что делать, но всë со временем. 

Share this post


Link to post
Share on other sites

Еще вопрос. Правильно ли я понимаю что в моей атс нет лицензий на использование сторонних телефонов sip ? По идее я могу подключить 4  внешние sip линии и 8 системных ip (именно panasonic) телефонов и больше ничего? А как же внутренние sip абоненты и самое главное, аналоговые телефоны и модемы? Для этого нужны отдельные лицензии? 

Screenshot_2025-01-18-10-38-15-223_com.anydesk.anydeskandroid.jpg

Screenshot_2025-01-18-10-38-38-467_com.anydesk.anydeskandroid.jpg

Share this post


Link to post
Share on other sites

Добрый день. Получается я и аналоговыми телефонами и соответственно модемами не могу пользоваться? Плат дохрена, а толку 0 🙂 и на Е1 тоже отдельная лицензия нужна? 

Share this post


Link to post
Share on other sites

Нет. на каждую плату своя "встроенная" лицензия. То есть если есть Н аналоговых линий, то все они рабочие по определению. На Е1 - аналогично: есть плата - есть "лицензия". Лицензии берутся за внешний функционал: типа системных телефонов (там на одну линиию можно получить 4 абонента), внутрений (не внешний) сип сервер, всякие автоответчики и теде.

Share this post


Link to post
Share on other sites

собрал пул на

[USR COURIER/...]->(3825:[VIC3-4FXS/DID+PVDM2-32]->[VWIC-1MFT-E1]->[NM-2CE1T1-PRI]->[NM-12DM])

 

конфиг брал в теме, немного исправил, все запустилось вышел в интернет через модем)

 

но возникла проблема если несколько раз переподключить модем, отваливается авторизация. лечу через reload(

 

в cisco понимание не особо, буду благодарен за любую помощь

 

Скрытый текст

service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Dial-UP_S
!
boot-start-marker
boot-end-marker
!
!
card type e1 2
no logging console
!
no aaa new-model
clock timezone MOS 3 0
network-clock-participate slot 2
network-clock-participate wic 1
network-clock-select 5 E1 2/1
network-clock-select 8 E1 2/0
!
modem call-record terse
modem country mica e1-default
dot11 syslog
ip source-route
!
!
!
ip cef
!
!
ip domain name dialup.net
no ipv6 cef
multilink bundle-name authenticated
!
!
!
async-bootp dns-server 8.8.8.8
isdn switch-type primary-net5
!
modemcap entry v12-v92:MSC=&W+qc=1,1;
voice-card 0
!
!
!
!
!
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3825 sn ************
username user privilege 15 secret 5 $1$Vuu6$b53l6eNLBPGqmbkCWKpM80
username dialup password 0 123456
!
!
controller E1 0/1/0
 framing NO-CRC4
 pri-group timeslots 1-16
!
controller E1 2/0
 framing NO-CRC4
 pri-group timeslots 1-16
!
controller E1 2/1
 framing NO-CRC4
 pri-group timeslots 1-5,16
!
ip ssh authentication-retries 2
ip ssh version 2
!
!
!
!
!
interface Loopback0
 ip address 11.1.1.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly in
!
interface GigabitEthernet0/0
 ip address 10.10.10.202 255.255.255.0
 ip nat outside
 ip virtual-reassembly in
 duplex auto
 speed auto
 media-type rj45
!
interface GigabitEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
 media-type rj45
!
interface Serial0/1/0:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn incoming-voice voice
 no cdp enable
!
interface Serial2/0:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn protocol-emulate network
 isdn incoming-voice modem 64
 no cdp enable
!
interface Serial2/1:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn protocol-emulate network
 isdn incoming-voice modem 64
 no cdp enable
!
interface Group-Async0
 ip unnumbered Loopback0
 ip nat inside
 ip virtual-reassembly in
 encapsulation ppp
 no ip route-cache
 load-interval 30
 dialer in-band
 dialer idle-timeout 600
 dialer-group 2
 peer default ip address pool dialin
 async mode interactive
 no keepalive
 ppp authentication chap
 group-range 1/0 1/4
 routing dynamic
!
ip local pool dialin 11.1.1.10 11.1.1.30
ip forward-protocol nd
!
!
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 2 interface GigabitEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 10.10.10.1
ip route 11.1.1.0 255.255.255.0 10.10.10.1
!
access-list 2 permit 11.1.1.0 0.0.0.255
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
voice-port 0/0/0
 compand-type a-law
 cptone RU
!
voice-port 0/0/1
 compand-type a-law
 cptone RU
!
voice-port 0/0/2
 compand-type a-law
 cptone RU
!
voice-port 0/0/3
 compand-type a-law
 cptone RU
!
voice-port 0/1/0:15
!
!
!
mgcp profile default
!
!
dial-peer voice 401 pots
 destination-pattern 11
 port 0/0/0
!
dial-peer voice 402 pots
 destination-pattern 12
 port 0/0/1
!
dial-peer voice 403 pots
 destination-pattern 13
 port 0/0/2
!
dial-peer voice 404 pots
 destination-pattern 14
 port 0/0/3
!
dial-peer voice 901 pots
 destination-pattern 91T
 no digit-strip
 direct-inward-dial
 forward-digits all
!
dial-peer voice 902 pots
 destination-pattern 92T
 no digit-strip
 direct-inward-dial
 forward-digits all
!
dial-peer voice 903 pots
 destination-pattern 9T
 no digit-strip
 direct-inward-dial
 port 0/1/0:15
 forward-digits all
!
!
!
!
line con 0
line aux 0
line 1/0 1/11
 exec-timeout 0 0
 no flush-at-activation
 logging synchronous
 login local
 modem InOut
 modem autoconfigure type v12-v92
 rotary 1
 exec-character-bits 8
 special-character-bits 8
 transport preferred none
 transport input all
 transport output all
 autoselect during-login
 autoselect ppp
 no ip tcp input-coalesce-threshold
line vty 0 4
 login local
 transport input ssh
line vty 5 15
 login local
 transport input ssh
!
scheduler allocate 20000 1000
end

 

Share this post


Link to post
Share on other sites

@alxndr 

Скажу так, я гонял симфонию из 6 или 7 модемов, которые непереставая и без пауз создают модемный шум часов 6 подряд.

Только не спрашивайте зачем мне это 🙂 так вот первым сглючил то ли usb порт, то ли usb-com шнурок. Атс и цифровые модемы отрабтали четко, но у меня там другая железяка стояла на цифровых модемах, более современная.

Чтобы понять что там отваливается надо включать дебаг логи в консоль, вариаций там масса логов. У меня нет под рукой, но я думаю что не проблема спросить у робота по нашему-то времени 🙂 вон дикпик новый китайский вышел

Share this post


Link to post
Share on other sites

@alxndr 

 

Вот что у меня в моих записях на эту тему debug цифровых модемов по cisco:

Не ручаюсь за достоверность, что-то может и не работать вовсе, неструктурированно и пр.

Но помню,  что многое и работало нормально

подцепиться к модему 322

telnet 172.0.0.1 2322



show modem log
clear modem log
debug pvdm2dm packet pvdm

debug isdn q931
debug modem csm
debug modem
terminal monitor

debug spe modem

no debug all
no logging console
terminal no monitor

show line

show sessions
disconnect 1

show modem configuration 0/0

 show modem log 1/28
terminal monitor
debug modem
spe modem trace all
debug spe modem stat
debug csm modem

debug cas
debug scp all


show modem operational-status

 

 

Кроме того обратил внимание, что в вашем конфиге строка подключения на v92.

Я бы рекомендовал переключиться на v90 так как v92 очень нестабилен по качеству соединения был.

 

modemcap entry mica-v90:MSC=&F&D2S0=0S29=6S21=3S34=18000S40=10S10=50
modemcap entry mica-v92:MSC=&F&D2S54=16584S0=0S29=12S21=15S62=8S63=3S34=18000S40=10S10=50

 

Надо понимать что это я все тоже в открытых источниках дергал и руки не дошли поразбираться с тонким тюнингом цифровых модемов.

Edited by get56k

Share this post


Link to post
Share on other sites

Get56k

 

я модемы не настраивал. настройки по дефолту

Скрытый текст

Dial-UP_S#show modem configuration 1/0
  S-Reg   Value   Meaning
 -------|-------|---------------------------------------------
    S-- = 0       Country Code is Default A-Law
    S00 = 2       Auto Answer after 2 seconds
    S01 = 0       Reserved
    S02 = 43      escape character is 0x2B or '+'
    S03 = 13      carriage return character is 0xD
    S04 = 10      line feed character is 0xA
    S05 = 8       backspace character is 0x8
    S06 = 2       pause 2 seconds before blind dialing
    S07 = 60      wait up to 60 seconds for carrier after dialing
    S08 = 2       comma adds 2 second dial delay
    S09 = 317     BitMap register value = 0x13D
    S10 = 14      1.4 second delay for hangup after carrier loss
    S11 = 0       In Answer Mode
    S12 = 8       8 Data Bits
    S13 = 0       No Parity
    S14 = 1       1 Stop Bits
    S15 = 1       V.42 ODP generation enabled
    S16 = 50      5.0 second Error Correction autodetect timeout
    S17 = 100     10.0 second Error Correction negotiation timeout
    S18 = 13      Error Correction fallback char is 0xD
    S19 = 12      Error Correction retransmission limit is 12
    S20 = 256     Error Correction frame length is 256 octets
    S21 = 15      V44, V42bis or MNP5 Data Compression
    S22 = 0       ARA Error Correction is disabled
    S23 = 1       V.42 Error Correction enabled
    S24 = 1       MNP Error Correction enabled
    S25 = 0       Link Protocol Fallback to Async framing
    S26 = 1       Using TDM slice 1
    S27 = 0       Calling Tone disabled
    S28 = 0       Guard Tone disabled
    S29 = 12      V.92 modem standard
    S30 = 33600   Maximum connect rate of 33600 bps
    S31 = 300     Minimum connect rate of 300 bps
    S32 = 2       Bit Errors >= 1:1000 cause recovery
    S33 = 500     Fallback/Fallforward Squelch Timer is 500ms
    S34 = 2000    Fall Forward Timer is 20.0 seconds
    S35 = 50      Fall Back Timer is 0.50 seconds
    S36 = 20      Terminate timeout is 20 seconds
    S37 = 60      Wait 60 seconds for data mode timeout
    S38 = 14      1.4 second lost carrier to hang-up delay
    S39 = 7       Transmit level setting of -13dBm
    S40 = 4       4 consecutive retrains cause link disconnect
    S41 = 5       V.34 maximum symbol rate of 3429 baud
    S42 = 0       V.34 minimum symbol rate of 2400 baud
    S43 = 2       V.34 carrier frequency is Auto Selection
    S44 = 11      V.34 Preemphasis filter selection is Automatic
    S45 = 0       Null transmit and receive Signalling Type
    S46 = 0       No call progress tone detection
    S47 = 2       +++ escape detection enabled for originate mode only
    S48 = 1       AT command processor enabled
    S49 = 0       no call setup delay
    S50 = 60000   Maximum PCM connect rate of 60000 bps
    S51 = 28000   Minimum PCM connect rate of 28000 bps
    S52 = 1       Digital Pad Compensation is enabled
    S53 = 3       V.8bis is enabled, V.90 negotiation inside V.8bis is enabled
    S57 = 9600    User rate for V.110 connection is  bps
    S58 = 0       V.110 Flow - Originate
    S61 = 115     MICA extension flags - 0x73
    S62 = 0       MOH disabled
    S63 = 3       QC enabled, ANSpcm level -12 dBm
    S65 = 2048    V.44 Max number of Tx codewords is 2048
    S66 = 2048    V.44 Max number of Rx codewords is 2048
    S67 = 255     V.44 Max Tx string length is 255
    S68 = 255     V.44 Max Rx string length is 255
    S69 = 15000   V.44 Max Tx history size is 15000
    S70 = 15000   V.44 Max Rx history size is 15000

 

 

проблема отвалов оказалась в  dialer idle-timeout 300

решилось добавлением в конфиг dialer-list 2 protocol ip permit

 

2,5 часа коннекта на закачку, и через 5 мин отключение как и должно)

тюнинг модемов тоже ни какой не делал

 

PCI модем v.90 ноута CONNECT at 54666/24000 (Tx/Rx), V90/92, LAPM, V44

Dlink v.92 Analog External modem CONNECT at 48000/28800 (Tx/Rx), V90/92, LAPM, V44 с поднятием  SpeedShifted to 48000/31200 (Tx/Rx)

USRobotics Courier  v.90 x2 CONNECT at 52000/28800 (Tx/Rx), V90/92, LAPM, V42bis с поднятием SpeedShifted to 52000/31200 (Tx/Rx)

 

нужен ли тюнинг, думаю нет. для своей игрушки вполне достаточно)

Спасибо за советы, похоже пока получить v.92 на обратке не вышло

 

и мой конфиг рабочий, на Ge0/0 настроен Dhcp может кому пригодится)

CISCO 3825:[VIC3-4FXS/DID+PVDM2-32]->[VWIC-1MFT-E1]->[NM-2CE1T1-PRI]->[NM-12DM]

 

Скрытый текст

service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Dial-UP_S
!
boot-start-marker
boot-end-marker
!
!
card type e1 2
no logging console
!
no aaa new-model
clock timezone MOS 3 0
network-clock-participate slot 2
network-clock-participate wic 1
network-clock-select 5 E1 2/1
network-clock-select 8 E1 2/0
!
modem call-record terse
modem country mica e1-default
dot11 syslog
ip source-route
!
!
!
ip cef
!
!
ip domain name dialup.net
no ipv6 cef
multilink bundle-name authenticated
!
!
!
async-bootp dns-server 8.8.8.8
isdn switch-type primary-net5
!
modemcap entry v12-v92:MSC=&W+qc=1,1;
voice-card 0
!
!
!
!
!
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3825 sn FCZ1223719A
username user privilege 15 secret 5 $1$Vuu6$b53l6eNLBPGqmbkCWKpM80
username dialup password 0 123456
!
!
controller E1 0/1/0
 framing NO-CRC4
 pri-group timeslots 1-16
!
controller E1 2/0
 framing NO-CRC4
 pri-group timeslots 1-16
!
controller E1 2/1
 framing NO-CRC4
 pri-group timeslots 1-5,16
!
ip ssh authentication-retries 2
ip ssh version 2
!
!
!
!
!
interface Loopback0
 ip address 11.1.1.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly in
!
interface GigabitEthernet0/0
 ip address dhcp
 ip nat outside
 ip virtual-reassembly in
 duplex auto
 speed auto
 media-type rj45
!
interface GigabitEthernet0/1
 no ip address
 shutdown
 duplex auto
 speed auto
 media-type rj45
!
interface Serial0/1/0:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn incoming-voice voice
 no cdp enable
!
interface Serial2/0:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn protocol-emulate network
 isdn incoming-voice modem 64
 no cdp enable
!
interface Serial2/1:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn protocol-emulate network
 isdn incoming-voice modem 64
 no cdp enable
!
interface Group-Async0
 ip unnumbered Loopback0
 ip nat inside
 ip virtual-reassembly in
 encapsulation ppp
 no ip route-cache
 load-interval 30
 dialer in-band
 dialer idle-timeout 300
 dialer-group 2
 peer default ip address pool dialin
 async mode interactive
 no keepalive
 ppp authentication chap
 group-range 1/0 1/4
 routing dynamic
!
ip local pool dialin 11.1.1.10 11.1.1.30
ip forward-protocol nd
!
!
ip http server
ip http authentication local
no ip http secure-server
ip nat inside source list 2 interface GigabitEthernet0/0 overload
ip route 11.1.1.0 255.255.255.0 GigabitEthernet0/0
ip route 0.0.0.0 0.0.0.0 dhcp
!
access-list 2 permit 11.1.1.0 0.0.0.255
dialer-list 2 protocol ip permit
!
!
!
control-plane
!
!
voice-port 0/0/0
 compand-type a-law
 cptone RU
!
voice-port 0/0/1
 compand-type a-law
 cptone RU
!
voice-port 0/0/2
 compand-type a-law
 cptone RU
!
voice-port 0/0/3
 compand-type a-law
 cptone RU
!
voice-port 0/1/0:15
!
!
!
mgcp profile default
!
!
dial-peer voice 401 pots
 destination-pattern 11
 port 0/0/0
!
dial-peer voice 402 pots
 destination-pattern 12
 port 0/0/1
!
dial-peer voice 403 pots
 destination-pattern 13
 port 0/0/2
!
dial-peer voice 404 pots
 destination-pattern 14
 port 0/0/3
!
dial-peer voice 901 pots
 destination-pattern 91T
 no digit-strip
 direct-inward-dial
 forward-digits all
!
dial-peer voice 902 pots
 destination-pattern 92T
 no digit-strip
 direct-inward-dial
 forward-digits all
!
dial-peer voice 903 pots
 destination-pattern 9T
 no digit-strip
 direct-inward-dial
 port 0/1/0:15
 forward-digits all
!
!
!
!
line con 0
line aux 0
line 1/0 1/11
 exec-timeout 0 0
 no flush-at-activation
 logging synchronous
 login local
 modem InOut
 modem autoconfigure type v12-v92
 rotary 1
 exec-character-bits 8
 special-character-bits 8
 transport preferred none
 transport input all
 transport output all
 autoselect during-login
 autoselect ppp
 no ip tcp input-coalesce-threshold
line vty 0 4
 exec-timeout 0 0
 login local
 transport input ssh
line vty 5 15
 login local
 transport input ssh
!
scheduler allocate 20000 1000
ntp update-calendar
ntp server 0.ru.pool.ntp.org source GigabitEthernet0/0
end

 

 

Edited by alxndr
орфография)

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.