Jump to content
Калькуляторы

Настройка VLANов

Здравствуйте.  Испытываю некоторые проблемы при настройки VLANов на HP Office Connect 1920S, JL381A.

Имеется 1 cisco router, 1 core switch 5406rzl2, 2 mobility controller 7205, 22 штуки 2930F JL259A и около 100 штук этих 1920S.

Суть проблемы заключается в следующем:

Я пробросил вланы на 1920S транком, на самом свитче настроил пару партов транком с натив вланом 101 для AP305 и влан 202 для раздачи сети под wifi, и попытался настроить остальные порты под access vlan 202.

Wi-Fi аппараты получили свои айпи и раздают сеть нормально. Access же не работает, оборудование не получает ip по dhcp (телики, компы, и т.д.). При этом на тестовом свитче у меня все отлично работает. Прилагаю startup-conf.

!Current Configuration:
!
!System Description "HPE OfficeConnect Switch 1920S 24G 2SFP JL381A, PD.01.05, Linux 3.6.5-ac96795c, U-Boot 2012.10-00118-g3773021 (Oct 11 2016 - 15:39:54)"
!System Software Version "PD.01.05"
!System Up Time          "0 days 0 hrs 34 mins 12 secs"
!Additional Packages     HPE QOS,HPE IPv6 Management,HPE Routing
!Current SNTP Synchronized Time: SNTP Client Mode Is Disabled
!
network protocol none
network parms 172.30.0.216 255.255.255.0 172.30.0.1
vlan database
vlan 100-101,202
vlan name 100 "management"
exit
network mgmt_vlan 100
ip telnet server enable
configure
sntp server "46.19.96.19"
!clock timezone 4 minutes 0
clock timezone id 57
time-range Schedule-1
exit
time-range Schedule-2
exit
username "admin" password 888 level 15 encrypted
no username guest
line console
exit
line telnet
exit
line ssh
exit
snmp-server sysname "SW3502"
snmp-server location "28 Floor, apartment 02"
snmp-server contact "Endspiel"
!
interface 1
vlan participation include 100-101,202
vlan tagging 100-101,202
exit
interface 2
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 3
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 4
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 5
vlan pvid 202
vlan participation exclude 1,100
vlan participation include 202
exit
interface 6
vlan pvid 202
vlan participation exclude 1,100
vlan participation include 202
exit
interface 7
vlan pvid 202
vlan participation exclude 1,100
vlan participation include 202
exit
interface 8
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 9
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 10
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 11
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 12
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 13
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 14
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 15
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 16
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 17
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 18
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 19
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 20
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 21
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 22
vlan pvid 202
vlan participation exclude 1
vlan participation include 202
exit
interface 23
vlan pvid 101
vlan participation exclude 1
vlan participation include 101,202
vlan tagging 202
exit
interface 24
vlan pvid 101
vlan participation exclude 1
vlan participation include 101,202
vlan tagging 202
exit
exit

Не понимаю в чем может быть проблема при идентичных настройках на тестовом свитче и на этом.

 

Share this post


Link to post
Share on other sites

Смотрите таблицу коммутации. Проверяйте без дхцп. Делайте зеркало порта и смотрите снифером.

Share this post


Link to post
Share on other sites
2 часа назад, Endspiel сказал:

PD.01.05, Linux 3.6.5-ac96795c, U-Boot 2012.10-00118-g3773021 (Oct 11 2016 - 15:39:54)

Я думаю, начать надо с обновления: http://h17007.www1.hpe.com/OfficeConnect/?PRE=1920S

 

После него конфиг убить, сделать с нуля. 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this