Перейти к содержимому
Калькуляторы

Edgerouter X восстановление прошивки

Ответить

keeper1978   

keeper1978
Опубликовано (изменено) · Жалоба

Помогите оживить EdgerouterX Настраивал сертефикаты lets encrypt , всё настроил сутки полет был нормальный до перезагрузки роутера.

в итоге он загружается, по лампочкам видно что идут какие то пакеты но сам роутер не доступен ни в каком из диапозонов, и дискавери не сканируется.

подскажите как то можно попытаться его оживить ?

Изменено пользователем keeper1978

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

saaremaa   

saaremaa
Опубликовано · Жалоба

Пробовали? → EdgeRouter - Reset to Factory Defaults

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано · Жалоба
24 minutes ago, saaremaa said:

Пробовали? → EdgeRouter - Reset to Factory Defaults

Сбровы при выполнении и включении пробовал а из cli нет так как к консоли доступ получить не могу

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

saaremaa   

saaremaa
Опубликовано · Жалоба

Telnet и SSH недоступны? если рекомендации вендора не срабатывают - тут фз...с таким не сталкивались...

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано · Жалоба

к 192.168.1.1 подключится не получается ни по какому протоколу

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

saaremaa   

saaremaa
Опубликовано · Жалоба

Тогда остается UART если есть переходник. https://community.ubnt.com/t5/EdgeRouter/Edge-Router-X-USB-TTL/td-p/1419788

https://community.ubnt.com/t5/EdgeRouter/Edgerouter-X-ER-X-USB-TTL-Serial-Port-Mod/td-p/1662131

Сам не цеплялся к Edgerouter X но иногда используем на другом железе.

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано · Жалоба

ооо а вот за э

12 hours ago, saaremaa said:

Тогда остается UART если есть переходник. https://community.ubnt.com/t5/EdgeRouter/Edge-Router-X-USB-TTL/td-p/1419788

https://community.ubnt.com/t5/EdgeRouter/Edgerouter-X-ER-X-USB-TTL-Serial-Port-Mod/td-p/1662131

Сам не цеплялся к Edgerouter X но иногда используем на другом железе.

ооо а вот за это спасибо буду пробовать

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано (изменено) · Жалоба 
===================================================================
                MT7621   stage1 code 10:33:11 (ASIC)
                CPU=50000000 HZ BUS=16666666 HZ
==================================================================
Change MPLL source from XTAL to CR...
do MEMPLL setting..
MEMPLL Config : 0x11100000
3PLL mode + External loopback
=== XTAL-40Mhz === DDR-1200Mhz ===
PLL2 FB_DL: 0x13, 1/0 = 635/389 4D000000
PLL4 FB_DL: 0x16, 1/0 = 602/422 59000000
PLL3 FB_DL: 0x19, 1/0 = 545/479 65000000
do DDR setting..[00320381]
Apply DDR3 Setting...(use customer AC)
          0    8   16   24   32   40   48   56   64   72   80   88   96  104  112  120
      --------------------------------------------------------------------------------
0000:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0001:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0002:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0003:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0004:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0005:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0006:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0007:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0008:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0009:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
000D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    1    1
000E:|    0    0    0    0    0    0    0    0    1    1    1    1    1    1    1    1
000F:|    0    0    0    0    1    1    1    1    1    1    1    1    1    0    0    0
0010:|    1    1    1    1    1    1    1    1    0    0    0    0    0    0    0    0
0011:|    1    1    1    1    0    0    0    0    0    0    0    0    0    0    0    0
0012:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0013:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0014:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0015:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0016:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0017:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0018:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
0019:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001A:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001B:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001C:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001D:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001E:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
001F:|    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0    0
rank 0 coarse = 15
rank 0 fine = 64
B:|    0    0    0    0    0    0    0    0    1    1    1    0    0    0    0    0
opt_dle value:9
DRAMC_R0DELDLY[018]=00001D1C
==================================================================
                RX      DQS perbit delay software calibration
==================================================================
1.0-15 bit dq delay value
==================================================================
bit|     0  1  2  3  4  5  6  7  8  9
--------------------------------------
0 |    12 8 11 10 11 7 12 6 6 10
10 |    8 12 7 12 9 12
--------------------------------------

==================================================================
2.dqs window
x=pass dqs delay value (min~max)center
y=0-7bit DQ of every group
input delay:DQS0 =28 DQS1 = 29
==================================================================
bit     DQS0     bit      DQS1
0  (1~55)28  8  (1~49)25
1  (1~52)26  9  (1~54)27
2  (1~53)27  10  (1~53)27
3  (1~53)27  11  (0~50)25
4  (1~55)28  12  (1~51)26
5  (1~53)27  13  (1~53)27
6  (1~55)28  14  (3~55)29
7  (1~53)27  15  (2~55)28
==================================================================
3.dq delay value last
==================================================================
bit|    0  1  2  3  4  5  6  7  8   9
--------------------------------------
0 |    12 10 12 11 11 8 12 7 10 12
10 |    10 15 10 14 9 13
==================================================================
==================================================================
     TX  perbyte calibration
==================================================================
DQS loop = 15, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqsdly_pass[0]=15,  finish count=1
dqs_perbyte_dly.last_dqsdly_pass[1]=15,  finish count=2
DQ loop=15, cmp_err_1 = ffff01aa
DQ loop=14, cmp_err_1 = ffff01a0
DQ loop=13, cmp_err_1 = ffff0080
dqs_perbyte_dly.last_dqdly_pass[1]=13,  finish count=1
DQ loop=12, cmp_err_1 = ffff0080
DQ loop=11, cmp_err_1 = ffff0000
dqs_perbyte_dly.last_dqdly_pass[0]=11,  finish count=2
byte:0, (DQS,DQ)=(a,8)
byte:1, (DQS,DQ)=(9,8)
20,data:9a
[EMI] DRAMC calibration passed

===================================================================
                MT7621   stage1 code done
                CPU=50000000 HZ BUS=16666666 HZ
===================================================================


U-Boot 1.1.3 (Nov  2 2015 - 16:39:31)

Board: Ralink APSoC DRAM:  256 MB
relocate_code Pointer at: 8ffb0000

Config XHCI 40M PLL
Allocate 16 byte aligned buffer: 8ffe1960
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [01 DA 90 95 46]
Device found in MTK table, ID: 1da, EXT_ID: 909546
Support this Device in MTK table! 1da
select_chip
[NAND]select ecc bit:12, sparesize :112 spare_per_sector=28
Signature matched and data read!
load_fact_bbt success 2047
load fact bbt success
[mtk_nand] probe successfully!
mtd->writesize=2048 mtd->oobsize=112,   mtd->erasesize=131072  devinfo.iowidth=8
..
UBNT e50 13-02079-18 F09FC20DC260
UBNT BD type=e50, mac=F09FC20DC260, s/n=F09FC20DC260, mrev=18, k_idx=0
============================================
Ralink UBoot Version: 4.3.S.0
--------------------------------------------
ASIC MT7621A DualCore (MAC to MT7530 Mode)
DRAM_CONF_FROM: Auto-Detection
DRAM_TYPE: DDR3
DRAM bus: 16 bit
Xtal Mode=3 OCP Ratio=1/3
Flash component: NAND Flash
Date:Nov  2 2015  Time:16:39:31
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:256, ways:4, linesz:32 ,total:32768

 ##### The CPU freq = 880 MHZ ####
 estimate memory size =256 Mbytes
#Reset_MT7530
set port isolation

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.
default: 3                                                                    0

3: System Boot system code via Flash.
## Booting image at bfd40000 ...
   Image Name:   Linux Kernel Image
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1719657 Bytes =  1.6 MB
   Load Address: 81001000
   Entry Point:  81380480
...........................   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 81380480) ...
## Giving linux memsize in MB, 256

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 3.10.107-UBNT (root@aa3a2d4ee03f) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Fri Jun 22 16:22:40 UTC 2018

 The CPU feqenuce set to 880 MHz
GCMP present
CPU0 revision is: 0001992f (MIPS 1004Kc)
Software DMA cache coherency
Determined physical RAM map:
 memory: 10000000 @ 00000000 (usable)
Zone ranges:
  DMA      [mem 0x00000000-0x00ffffff]
  Normal   [mem 0x01000000-0x0fffffff]
  HighMem  empty
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x00000000-0x0fffffff]
Detected 3 available secondary CPU(s)
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
PERCPU: Embedded 7 pages/cpu @81704000 s6144 r8192 d14336 u32768
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: console=ttyS1,57600n8 ubi.mtd=7 root=ubi0_0 rootfstype=ubifs rootsqimg=squashfs.img rootsqwdir=w rw
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Writing ErrCtl register=00018541
Readback ErrCtl register=00018541
Memory: 254620k/262144k available (3614k kernel code, 7524k reserved, 1034k data, 208k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
console [ttyS1] enabled
Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072)
pid_max: default: 32768 minimum: 301
Security Framework initialized
Mount-cache hash table entries: 512
launch: starting cpu1
launch: cpu1 gone!
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU1 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 1: done.
launch: starting cpu2
launch: cpu2 gone!
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU2 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 2: done.
launch: starting cpu3
launch: cpu3 gone!
Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
CPU3 revision is: 0001992f (MIPS 1004Kc)
Synchronize counters for CPU 3: done.
Brought up 4 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
4 CPUs re-calibrate udelay(lpj = 1167360)
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering unionfs 2.5.13 (for 3.10.34)
aufs 3.10.x-20141215
msgmni has been set to 497
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A
serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A
Ralink gpio driver initialized
i2cdrv_major = 218
loop: module loaded
flash manufacture id: 1c, device id 70 15
EN25QH16(1c 70151c70) (2048 Kbytes)
mtd .name = raspi, .size = 0x00200000 (2M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
Creating 1 MTD partitions on "raspi":
0x000000000000-0x000000080000 : "SPI_FLASH"
MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error
Allocate 16 byte aligned buffer: 814e6540
Enable NFI Clock
# MTK NAND # : Use HW ECC
NAND ID [01 DA 90 95 46, 00909546]
Device found in MTK table, ID: 1da, EXT_ID: 909546
Support this Device in MTK table! 1da
NAND device: Manufacturer ID: 0x01, Chip ID: 0xda (AMD/Spansion NAND 256MiB 3,3V 8-bit), 256MiB, page size: 2048, OOB size: 112
[NAND]select ecc bit:12, sparesize :112 spare_per_sector=28
Scanning device for bad blocks
Signature matched and data read!
load_fact_bbt success 2047
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Creating 7 MTD partitions on "MT7621-NAND":
0x000000000000-0x00000ff80000 : "ALL"
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x0000000e0000 : "Config"
0x0000000e0000-0x000000140000 : "eeprom"
0x000000140000-0x000000440000 : "Kernel"
0x000000440000-0x000000740000 : "Kernel2"
0x000000740000-0x00000ff00000 : "RootFS"
[mtk_nand] probe successfully!
UBNT BD mac f09fc20dc260 kidx 0 mrev 18 serial F09FC20DC260 type e50
rdm_major = 253
GMAC1_MAC_ADRH -- : 0x0000f09f
GMAC1_MAC_ADRL -- : 0xc20dc260
Ralink APSoC Ethernet Driver Initilization. v3.1  512 rx/tx descriptors allocated, mtu = 1500!
GMAC1_MAC_ADRH -- : 0x0000f09f
GMAC1_MAC_ADRL -- : 0xc20dc260
PROC INIT OK!
Ralink I2C Init
TCP: cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
UBI: attaching mtd7 to ubi0
UBI: scanning is finished
UBI: attached mtd7 (name "RootFS", size 247 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 1982, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 51/10, WL threshold: 4096, image sequence number: 954399611
UBI: available PEBs: 0, total reserved PEBs: 1982, PEBs reserved for bad PEB handling: 40
UBI: background thread "ubi_bgt0d" started, PID 54
UBIFS: background thread "ubifs_bgt0_0" started, PID 55
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "troot"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 244428800 bytes (233 MiB, 1925 LEBs), journal size 12189696 bytes (11 MiB, 96 LEBs)
UBIFS: reserved for root: 4952683 bytes (4836 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID B7DEF713-FB42-439E-87FD-1DF4D149FC55, small LPT model
VFS: Mounted root (aufs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 208K (8148c000 - 814c0000)
Algorithmics/MIPS FPU Emulator v1.5
INIT: version 2.88 booting
aufs au_dtime_revert:148:init[60]: restoring timestamps failed(-28). ignored
aufs au_dtime_revert:148:init[60]: restoring timestamps failed(-28). ignored
aufs au_dtime_revert:148:init[60]: restoring timestamps failed(-28). ignored
aufs au_dtime_revert:148:init[60]: restoring timestamps failed(-28). ignored
aufs au_dtime_revert:148:S01ubnt-rcS[66]: restoring timestamps failed(-28). ignored
aufs au_dtime_revert:148:S01ubnt-rcS[66]: restoring timestamps failed(-28). ignored
/etc/rcS.d/S01ubnt-rcS: line 31: /etc/ubnt/last_time: No space left on device
cat: can't open '/etc/ubnt/last_time': No such file or directory
mkdir: can't create directory '/dev/shm/network': No such file or directory
chown: /root.dev/www: No space left on device
touch: /etc/ubnt/firstboot: No space left on device
[ ok ] Starting the hotplug events dispatcher: udevd.
[ ok ] Synthesizing the initial hotplug events...done.
[ ok ] Waiting for /dev to be fully populated...done.
INIT: Entering runlevel: 2
Unable to open file: /dev/tpm0
can't open any entropy source
Maybe RNG device modules are not loaded

[....] Starting SSH recovery service in the background
ssh-recovery: starting...
ssh-recovery: if=(all) port=(60257) terminate-timeout=(60)
update-rc.d: unlink: No space left on device
/etc/rc2.d/S01ubnt-init: line 24: /etc/monit/monitrc: No space left on device
[....] Starting daemon monitor: monitmonit: Error opening the idfile '/var/lib/monit/id' -- No space left on device
. ok
[....] Starting routing daemon: ribmonit: Error opening the idfile '/var/lib/monit/id' -- No space left on device
monit: service 'imi' -- doesn't exist
 nsmmonit: Error opening the idfile '/var/lib/monit/id' -- No space left on device
monit: service 'nsm' -- doesn't exist
 ribdmonit: Error opening the idfile '/var/lib/monit/id' -- No space left on device
monit: service 'ribd' -- doesn't exist
open /etc/ssh/ssh_host_key failed: No space left on device.
. ok
cp: can't create '/opt/vyatta/etc/config.boot.default': No space left on device
/opt/vyatta/etc/config.boot.default created
/etc/rc2.d/S03vyatta-router: line 75: /config/config.boot: No space left on device
chgrp: /config/config.boot: No such file or directory
chmod: /config/config.boot: No such file or directory
[....] Starting EdgeOS router: migrate rl-systemmkdir: can't create directory '/config/wizard/': No space left on device
chown: /config/wizard: No such file or directory
open /etc/ssh/ssh_host_rsa_key failed: No space left on device.
open /etc/ssh/ssh_host_dsa_key failed: No space left on device.
open /etc/ssh/ssh_host_ecdsa_key failed: No space left on device.
open /etc/ssh/ssh_host_ed25519_key failed: No space left on device.
ssh-recovery: enabling link on interfaces...
ssh-recovery: eth0 :: mac=(f0:9f:c2:0d:c2:60)
ssh-recovery: eth1 :: mac=(f0:9f:c2:0d:c2:61)
ssh-recovery: eth2 :: mac=(f0:9f:c2:0d:c2:62)
ssh-recovery: eth3 :: mac=(f0:9f:c2:0d:c2:63)
ssh-recovery: eth4 :: mac=(f0:9f:c2:0d:c2:64)
ssh-recovery: switch0 :: mac=(f0:9f:c2:0d:c2:65)
Could not load host key: /etc/ssh/ssh_host_rsa_key
Could not load host key: /etc/ssh/ssh_host_dsa_key
Could not load host key: /etc/ssh/ssh_host_key
Could not load host key: /etc/ssh/ssh_host_ecdsa_key
Could not load host key: /etc/ssh/ssh_host_ed25519_key
Could not load host key: /etc/ssh/ssh_host_rsa_key
Could not load host key: /etc/ssh/ssh_host_dsa_key
Could not load host key: /etc/ssh/ssh_host_key
Could not load host key: /etc/ssh/ssh_host_ecdsa_key
Could not load host key: /etc/ssh/ssh_host_ed25519_key
ssh-recovery: service started :: pid=(798)
touch: /etc/lighttpd/server.pem: No space left on device
chmod: /etc/lighttpd/server.pem: No such file or directory
chown: /etc/lighttpd/server.pem: No such file or directory
chmod: /etc/lighttpd/server.pem: No such file or directory
sync: ignoring all arguments
/opt/vyatta/sbin/rl-system.init: line 50: /etc/snmp/snmpd.conf: No space left on device
chmod: /etc/snmp/snmpd.conf: No space left on device
/opt/vyatta/sbin/rl-system.init: line 50: /etc/snmp/snmptrapd.conf: No space left on device
chmod: /etc/snmp/snmptrapd.conf: No space left on device
/opt/vyatta/sbin/rl-system.init: line 50: /etc/snmp/snmp.conf: No space left on device
chmod: /etc/snmp/snmp.conf: No space left on device
/opt/vyatta/sbin/rl-system.init: line 50: /etc/resolv.conf: No space left on device
chmod: /etc/resolv.conf: No space left on device
rm: can't remove '/etc/pam_radius_auth.conf': No space left on device
cp: can't create '/etc/securetty': File exists
cp: can't create '/etc/ssh/sshd_config': File exists
cp: can't create '/etc/default/ssh': File exists
/etc/ubnt/pre-config.d/dhcp-options:
grep: /config/config.boot: No such file or directory
[ ok igure.
Warning: /opt/vyatta/etc/config.boot.default: No such file or directoryrm: can't remove '/etc/nologin': No space left on device
chmod: /: No space left on device
Starting network plug daemon: netplugd.
[....] Starting daemon monitor: monitmonit: Error opening the idfile '/var/lib/monit/id' -- No space left on device
. ok

Welcome to EdgeOS ubnt ttyS1

By logging in, accessing, or using the Ubiquiti product, you
acknowledge that you have read and understood the Ubiquiti
License Agreement (available in the Web UI at, by default,
http://192.168.1.1) and agree to be bound by its terms.

ubnt login:

получил вывод по сериал 

только почемуто не подходят логин и пароль ubnt/ubnt

 

Изменено пользователем keeper1978

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано · Жалоба

может через консоль какие то свои логин и пароль

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано · Жалоба

не подходят тоже пробовал

 

 

может есть какой то способ загрузить по сериал прошивку, ткните на подходящий мануал

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

keeper1978   

keeper1978
Опубликовано (изменено) · Жалоба

делаю по этому мануалу https://community.ubnt.com/t5/EdgeRouter/ERX-ERX-SFP-System-Recovery/td-p/2056921

дохожу до команды  

ubiformat /dev/mtd5

выдает

ubiformat: error!: please, first detach mtd5 (/dev/mtd5) from ubi0
 

в чем может быть проблема ?

решение 

ubidetach -p /dev/mtd5

 

Ура всё востановил всё работает Ураааа !!!

Изменено пользователем keeper1978

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

saaremaa   

saaremaa
Опубликовано · Жалоба

Вот и хорошо. Сохраню на будущее - может и пригодится. У нас их всего 2 - брали на тест. 

Поделиться сообщением

Ссылка на сообщение
Поделиться на других сайтах

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Гость
Ответить в тему...

×   Вставлено в виде отформатированного текста.   Вставить в виде обычного текста

  Разрешено не более 75 смайлов.

×   Ваша ссылка была автоматически встроена.   Отобразить как ссылку

×   Ваш предыдущий контент был восстановлен.   Очистить редактор

×   Вы не можете вставить изображения напрямую. Загрузите или вставьте изображения по ссылке.

×
Подписчики 0
Перейти к списку тем Ubiquiti Networks