Azizbek Опубликовано 16 мая, 2017 · Жалоба Здравствуйте уважаемые коллеги, впервые встретился с платой ETHB (Ethernet optical port) на OLT Huawei MA5680T SmartMAX, те кто раньше работал с подобными платами, огромная просьба скиньте пример их использования, мне сказали что это плата аплинка, но также она может отдавать vlan, перечитал кучу статей на китайском языке, но результата это не дало, примера конфига просто нету. Заранее благодарен за ответ Кстати, display patch all Software Version:MA5600V800R011C00 SPC100 SPH109 HP1109 ------------------------------------------------------------------------ Current Patch State: ------------------------------------------------------------------------ Patch Name Patch State Delivery Attribute Dependency ------------------------------------------------------------------------ SPC100 running common cold patch NO SPH109 running common hot patch NO HP1109 running common hot patch NO ------------------------------------------------------------------------ Total:3 Patches in the system cannot be rolled back Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
Azizbek Опубликовано 16 мая, 2017 · Жалоба MA5680T(config)#display board 0 ------------------------------------------------------------------------- SlotID BoardName Status SubType0 SubType1 Online/Offline ------------------------------------------------------------------------- 0 1 H801ETHB Normal X1HA 2 H801ETHB Normal X1HA MA5680T(config)#display board 0/1 --------------------------------------- Board Name : H801ETHB Board Status : Normal --------------------------------------- ------------------------------------------------------------------------------ Power Status Power-off cause Power-off Time ------------------------------------------------------------------------------ POWER-ON - - ------------------------------------------------------------------------------ Subboard[0]: H801X1HA Status: Normal ------------------------------------------------------------------------------ Port Port Optic Native MDI Speed Duplex Flow- Active Link Type Status VLAN (Mbps) Ctrl State ------------------------------------------------------------------------------ 0 GE absence 1 - auto auto off active offline 1 GE absence 1 - auto auto off active offline 2 GE absence 1 - auto auto off active offline 3 GE absence 1 - auto auto off active offline 4 GE absence 1 - auto auto off active offline 5 GE absence 1 - auto auto off active offline 6 GE absence 1 - auto auto off active offline 7 GE absence 1 - auto auto off active offline ------------------------------------------------------------------------------ ------------------------------------------------------------------------------ Port 15Min 15Min 24Hour 24Hour AlmProf WarnProf AlmProf WarnProf ------------------------------------------------------------------------------ 0 - - - - 1 - - - - 2 - - - - 3 - - - - 4 - - - - 5 - - - - 6 - - - - 7 - - - - ------------------------------------------------------------------------------ Note: For any port, setting MDI to auto-negotiation is invalid, For a 1000 M Electrical port in the full-duplex mode, setting MDI to any value is invalid Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
sudo Опубликовано 16 мая, 2017 · Жалоба такой платы нет в наличии, но судя по описаниям, обычная эзернет плата, думаю можно использовать как для подлючения фреймов и аплинк. Попробуйте просто типа port vlan 333 0/1 0. и посмотрите выходит ли чтото из порта Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...
Azizbek Опубликовано 16 мая, 2017 · Жалоба такой платы нет в наличии, но судя по описаниям, обычная эзернет плата, думаю можно использовать как для подлючения фреймов и аплинк. Попробуйте просто типа port vlan 333 0/1 0. и посмотрите выходит ли чтото из порта думаю вы были правы! MA5680T(config)#interface eth 0/1 MA5680T(config-if-eth-0/1)#display ? --------------------------------------------- Command of eth Mode: --------------------------------------------- board Display information of board car-port CAR of port and CoS eth Eth profile mac-address Mac-address command group mirror Display mirror information network-role Network role offline-tx-off-time Display disable time of optical port of tx port <Group> port command group stack-port Stack port statistics Display statistics of ethernet port tag-transform Display the state of the tag transformation traffic-suppress Display information of port traffic suppression MA5680T(config)#interface eth 0/2 MA5680T(config-if-eth-0/2)#? --------------------------------------------- Command of eth Mode: --------------------------------------------- alarm-config Bind alarm profile to ethernet port auto-neg Enable/Disable port negotiation car-port CAR of port and CoS display Display information duplex Set duplex eth Eth profile flow-control Support flow control jumbo-frame Set jumbo frame enable/disable loopback Set loopback mac-address Mac-address command group mdi Line-adaptive function mirror Add mirror native-vlan Set defaulted VLAN ID network-role Network role offline-tx-off-time Set the disable time of optical port of tx port Set port quit Exit from current mode and enter prior mode reset Clear port statistics return Enter the privileged mode shutdown Deactivate port speed Rate switch Switch language mode tag-transform Set the state of tag transformation traffic-suppress Set port traffic suppression tx-auto-off Auto disable tx of optical port undo Negate a command or set its defaults Вставить ник Цитата Ответить с цитированием Поделиться сообщением Ссылка на сообщение Поделиться на других сайтах More sharing options...