RN3DCX Posted April 21, 2017 Кто из спецов подскажет как скинуть пароль у джуна SSG 520M. По гуглив, в мануалах пишут что нужно так: Для восстановления доступа необходимо: Подключиться к оборудованию с помощью консольного кабеля с нашего компьютера, любой терминальной программой. Осуществить перезапуск оборудования и наблюдать на экране сообщения. ! Loading /boot/defaults/loader.conf /kernel data=0xb4ac4c+0x5c744 syms=[0x4+0x83830+0x4+0x872e3] Hit [Enter] to boot immediately, or space bar for command prompt. ! Заметив надпись «Hit [Enter] to boot immediately, or space bar for command prompt.» необходимо успеть нажать клавишу «пробел» и пронаблюдать следующую картину: ! Type ‘?’ for a list of commands, ‘help’ for more detailed help. loader> ! Но как обычно по закону подлости подобной записи я при загрузке не обнаружил.... Trying to boot from Primary Compact Flash ... boot1... w lba boot2..... ScreenOS Saipanloader V1.0.7 Built Mar 19 2009/15:54:12 watchdog_probe, 1132 bus/dev/fn = 0/248 ich = 2640 boot_drive = 80 start1 = 2976, start2 = 14880 Hit 'X' and 'A' to upgrade bootloadermounting FAT16 partition file size = 112 size = 112, sizeof(nvram_rec) = 112 Hit any key to load new firmware Hit any key to load new firmware Hit any key to load new firmware Hit any key to load new firmware/$nsboot$.bin file size = 11553519 hdr->magic_number = 81ba16ee, hdr->platform_type = 1700, hdr->cpu_type = 11 Ignore image authentication! loading elf format.... <0x4000000:0x48f5:0x0> move image from 1001020 -> 4000000, size = 18677 <0x4005000:0xafe000:0x50d8> move image from 1006020 -> 4005000, size = 11546840 real_entry_addr = 4000000, entry_addr = 4000000 Uncompressing Kernel... Now booting the kernel the system has been up for 0 second(s) the system has been up for 0 second(s) CPU:GenuineIntel Version Information: Extended Family ID = 0 Extended Model ID = 0 Family ID = f Model = 4 Stepping ID = 9 Processor Type = 0 Brand String = 0 Additional Information: Brand Index = 0 CLFLUSH Line Size = 64 Initial APIC ID = 0 Feature Information: FPU VME DE PSE TSC MSR PAE MCE CX8 APIC SEP MTRR PGE MCA CMOV PAT PSE-36 CLFSH DS ACPI MMX FXSR SSE SSE2 SS HTT TM PBE Extended Feature Information: SSE3 MONITOR/MWAIT DS-CPL TM2 CNXT-ID TLB/Cache Information: 1st-level data cache: 16 KByte, 8-way set associative, 64 byte line size Data TLB: 4 KByte and 4 MByte pages, 64 entries Instruction TLB: 4 KByte and 2-MByte or 4-MByte pages, 128 entries Instruction TLB: 4 KByte Pages, 4-way set associative, 32 entries 2nd-level cache: 256-KB, 4-way set associative, sectored cache, 64-byte line siz e Trace cache: 12 K-ooooop, 8-way set associative No 2nd-level cache or, if processor contains a valid 2nd-level cache, no 3rd-lev el cache 3: eax = 0, ebx = 0, ecx = 0, edx = 0 4: eax = 121, ebx = 1c0003f, ecx = 1f, edx = 0 eax = 40, ebx = 40, ecx = 0, edx = 0 count = 80000008 Brand String: Intel® Celeron® CPU 2.53GHz L1 I Cache: 0K (0 bytes/line), D cache 0K (0 bytes/line) L2 Cache: 256K (64 bytes/line) total DRAM size is 1048576 KB init 0(+100000) heap 100000(+2bf00000) iocard 2c000000(+1400000) packet 2d400000(+800000) CTRL 2dc00000(+400000) TASK 2e000000(+12000000) heap_start = 2509010, heap_size = 29af6ff0 RCBA = fed1c001 FD = f8ef1 MAP = 1 MAP = 1 bootmap_size = 8000 zone_table[ZONE_TASK].free_pages = 71670, zone_table[ZONE_TASK].num_pages = 7372 8 _fbss = 1cfd000, _end = 2509000 data_start = 11e6000, data_end = 1cdc000 Juniper Networks, Inc SSG520/SSG550 System Software Copyright, 1997-2008 Version 6.3.0r6.0 set_ecb_dcr: not implemented scan pci 0 devices.... Device found on PCI bus 0:dev_num is 0,vendor id is 0x25888086 Device found on PCI bus 0:dev_num is 1,vendor id is 0x25898086 Device found on PCI bus 0:dev_num is 29,vendor id is 0x26588086 Device found on PCI bus 0:dev_num is 30,vendor id is 0x244e8086 Device found on PCI bus 0:dev_num is 31,vendor id is 0x26408086 scan pci 1 devices.... Device found on PCI bus 1:dev_num is 0,vendor id is 0x03298086 scan pci 2 devices.... Device found on PCI bus 2:dev_num is 2,vendor id is 0x90001148 Device found on PCI bus 2:dev_num is 3,vendor id is 0x90001148 cav_bar_init: called. Dump BARs PCI conf regs -- cav_bar_init: called. orig reg setting: PCI 10 = 0000e801, 18 = 0000e401 Load Manufacture Information ... init manufacture info Done cfcard ready. Install module init vectors Changed to l3 mode IO_CARD_BUF_START: 0x2c000000 ssg Searching GbE devices... On-board GbE device found, VID = 0x1148, DID = 0x9000 Bus 2, Slot 2 On-board GbE device found, VID = 0x1148, DID = 0x9000 Bus 2, Slot 3 Total on-board GbE devices found 2 Total adapter GbE devices found 0 Install modules (011e6000,01cdc000) ... PPP IP-POOL initiated, 256 pools Initializing DI 1.1.0-ns Done. System config (3026 bytes) loaded Done. Load System Configuration ...................................................... .............................................Admin status for interface ethernet 0/0.13 has been changed to disable .Admin status for interface ethernet0/0.90 has been changed to disable ................................................................................ ................................................................................ Disabled licensekey auto update ..........................Done system init done.. Load NVRAM Information ... (6.3.0)Done login: System change state to Active(1) login: Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
vvertexx Posted April 21, 2017 RN3DCX JunOS и ScreenOS случаем не путаешь? на SSG не знаю способов сброса пароля без сброса конфига полностью. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
RN3DCX Posted April 21, 2017 RN3DCX JunOS и ScreenOS случаем не путаешь? Да, я хз что там за ОС. Для этого спецально лог загрузки выложил. Т.к. балалайку марки juniper первый раз настраиваю... на SSG не знаю способов сброса пароля без сброса конфига полностью. Сойдет вариант и с сбросом конфига. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
vvertexx Posted April 21, 2017 RN3DCX Там ScreenOS, которая ничего общего с современной ОС juniper'а не имеет https://kb.juniper.net/InfoCenter/index?page=content&id=KB4749 http://kb.juniper.net/KB5046 (требуется регистрация, по сути полезного мало) Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
RN3DCX Posted April 21, 2017 https://kb.juniper.net/InfoCenter/index?page=content&id=KB4749 Да, пробовал и этот мануал. Пункт № 2 - при на нажатии (удержании) RESET пишет operation aborted. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
CityFox Posted April 22, 2017 Для сброса всего конфига на ScreenOS нужно подключиться консолью ( через ssh процедура не работает ) и ввести в качестве логина и пароля серийный номер железки. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
RN3DCX Posted April 23, 2017 Кстати, а чем отличается JunOS и ScreenOS ? Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
CityFox Posted April 23, 2017 Да между ними вообще нет ничего общего. NetScreen Technologies была отдельной компанией пока их Juniper не купил. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...