Jump to content
Калькуляторы

радиолинк на микротик автоматически не восстанавливается

К многоточке на Микротик RB912UAG5HPnD подключены неск. клиентов на Микротик Lite5. Нормально работают. Потом мороз или скачок напряжения, клиент отваливается, может иногда и присохнуть самостоятельно, но в основном вызов специалиста. Тарелка работает, видит чужие сети, а свою -нет. Переключаешь ее на другой сектор (другая частота и SSID другой) - моментально присыхает, обратно на свой - никак. Ставишь новую тарелку - всё ок. На сети такое стало происходить с неприятной регулярностью.

Подскажите, что это: аппаратный изъян или всё-таки в софте дело?

 

конфиг базы:

# dec/12/2016 11:26:38 by RouterOS 6.18

# software id = 16F6-H91M

#

/interface bridge

add l2mtu=1600 name=bridge1

/interface wireless

set [ find default-name=wlan1 ] band=5ghz-onlyn basic-rates-a/g="" \

channel-width=20/40mhz-ht-above disabled=no frequency=5350 \

frequency-mode=superchannel ht-basic-mcs=\

mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,

ht-rxchains=0,1 ht-supported-mcs=\

mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9,mcs-10,

ht-txchains=0,1 l2mtu=2290 mode=ap-bridge nv2-cell-radius=10 \

nv2-preshared-key=******** nv2-security=enabled rate-set=configured

S-K3 supported-rates-a/g="" tx-power=25 tx-power-mode=all-rates-fix

wds-default-bridge=bridge1 wds-mode=dynamic wireless-protocol=nstre

/interface wireless wds

add disabled=no master-interface=wlan1 name=3_20-Cen-12 wds-address=\

4C:5E:0C:07:F6:C1

add disabled=no master-interface=wlan1 name=3_44-Cen-32 wds-address=\

E4:8D:8C:90:D7:7F

/interface wireless nstreme

set wlan1 disable-csma=yes enable-nstreme=yes framer-policy=dynamic-siz

/interface wireless security-profiles

set [ find default=yes ] authentication-types=wpa-psk,wpa2-psk eap-meth

group-ciphers=tkip,aes-ccm mode=dynamic-keys supplicant-identity=Mi

unicast-ciphers=tkip,aes-ccm wpa-pre-shared-key=******** \

wpa2-pre-shared-key=********

/ip ipsec proposal

set [ find default=yes ] enc-algorithms=3des

/system logging action

set 0 memory-lines=100

set 1 disk-lines-per-file=100

/interface bridge filter

add action=drop chain=forward in-bridge=bridge1 in-interface=!ether1 \

out-bridge=bridge1 out-interface=!ether1

/interface bridge port

add bridge=bridge1 interface=ether1

add bridge=bridge1 interface=wlan1

/ip address

add address=10.0.39.251/24 interface=bridge1 network=10.0.39.0

/ip route

add distance=1 gateway=10.0.39.1

/ip service

set api disabled=yes

/ip upnp

set allow-disable-external-interface=no

/system clock manual

set time-zone=+05:00

/system identity

set name=Basa3-Sever

/system leds

set 0 interface=wlan1

/system logging

set 0 action=disk

set 1 action=disk

set 2 action=disk

set 3 action=disk

add action=echo topics=critical

/system ntp client

set enabled=yes primary-ntp=192.168.126.1

/system routerboard settings

set cpu-frequency=600MHz

/tool graphing interface

add interface=ether1 store-on-disk=no

/tool graphing resource

add store-on-disk=no

 

конфиг клиента:

# dec/12/2016 12:31:08 by RouterOS 6.10

# software id = FV6V-3JEZ

#

/interface bridge

add l2mtu=1598 name=bridge1

/interface wireless

set [ find default-name=wlan1 ] band=5ghz-a/n channel-width=20/40mhz-ht-above \

disabled=no frequency-mode=superchannel hw-protection-mode=rts-cts l2mtu=\

2290 mode=station-wds nv2-preshared-key=******** nv2-security=enabled \

radio-name=Cen-6 scan-list=5300-5400 ssid=S-K3 tx-power=10 tx-power-mode=\

all-rates-fixed wds-default-bridge=bridge1 wds-mode=dynamic

/interface wireless nstreme

set wlan1 enable-nstreme=yes

/interface wireless security-profiles

set [ find default=yes ] authentication-types=wpa-psk,wpa2-psk group-ciphers=\

tkip,aes-ccm mode=dynamic-keys supplicant-identity=MikroTik \

unicast-ciphers=tkip,aes-ccm wpa-pre-shared-key=******** \

wpa2-pre-shared-key=********

/ip hotspot user profile

set [ find default=yes ] idle-timeout=none keepalive-timeout=2m \

mac-cookie-timeout=3d

/interface bridge port

add bridge=bridge1 interface=ether1

add bridge=bridge1 interface=wlan1

/ip address

add address=10.0.39.229/24 interface=bridge1 network=10.0.39.0

/ip route

add distance=1 gateway=10.0.39.1

/ip upnp

set allow-disable-external-interface=no

/system clock manual

set time-zone=+06:00

/system identity

set name=Cen-6

/system leds

set 0 interface=wlan1

/system logging

set 0 action=disk

set 1 action=disk

set 2 action=disk

set 3 action=disk

/system ntp client

set enabled=yes mode=unicast primary-ntp=192.168.126.1 secondary-ntp=\

10.0.39.254

Share this post


Link to post
Share on other sites

Испытывал подобную проблему на одной CPE. Реальный полтергейст. Отдали по гарантии.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this