DanilKT Posted October 20, 2016 Добрый день! Прошу помощи! Имеется Cisco 7206VXR, модуль PC-MA-8TE1+.Пытаюсь настроить подключение к провайдеру по Е1. Физическая линия поднимается, сериальные интерфейсы создаются. Но команды voice-port просто нет. И show voice port summary ничего не показывает. Может не хватает каких-то модулей? Или версия IOS не та? Или что-то не дописал в конфиг? Router#sh version Cisco IOS Software, 7200 Software (C7200-ADVENTERPRISEK9-M), Version 12.4(24)T, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 26-Feb-09 00:31 by prod_rel_team ROM: System Bootstrap, Version 12.3(4r)T3, RELEASE SOFTWARE (fc1) BOOTLDR: Cisco IOS Software, 7200 Software (C7200-KBOOT-M), Version 12.4(12b), RELEASE SOFTWARE (fc2) Router uptime is 13 hours, 12 minutes System returned to ROM by reload at 21:23:28 MSK Wed Oct 19 2016 System restarted at 21:26:33 MSK Wed Oct 19 2016 System image file is "disk2:c7200-adventerprisek9-mz.124-24.T.bin" Last reload reason: Reload Command Cisco 7206VXR (NPE-G1) processor (revision C) with 983040K/65536K bytes of memory. Processor board ID 34188278 SB-1 CPU at 700MHz, Implementation 1025, Rev 0.2, 512KB L2 Cache 6 slot VXR midplane, Version 2.9 Last reset from power-on PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points. Current configuration on bus mb1 has a total of 0 bandwidth points. This configuration is within the PCI bus capacity and is supported. PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points. Current configuration on bus mb2 has a total of 0 bandwidth points. This configuration is within the PCI bus capacity and is supported. 3 Gigabit Ethernet interfaces 66 Serial interfaces 8 Channelized/Clear E1/PRI ports 509K bytes of NVRAM. 127488K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes). 16384K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2102 Router#show inventory NAME: "Chassis", DESCR: "Cisco 7206VXR, 6-slot chassis" PID: CISCO7206VXR , VID: , SN: 34188278 NAME: "NPE-G1 0", DESCR: "Cisco 7200 Series Network Processing Engine NPE-G1" PID: NPE-G1 , VID: V03 , SN: 36338871 NAME: "disk2", DESCR: "128MB Compact Flash Disk for NPE-G1" PID: MEM-NPE-G1-FLD128 , VID: , SN: NAME: "module 1", DESCR: "8 port, software configurable Multichannel T1/E1 without TDM Port Adapter" PID: PA-MC-8TE1+ , VID: , SN: JAE09044MKR NAME: "Power Supply 2", DESCR: "Cisco 7200 AC Power Supply" PID: PWR-7200-AC , VID: , SN: Router#show controllers e1 E1 1/0 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line. International Bit: 1, National Bits: 11111 Linestate Debounce is disabled Data in current interval (749 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 50 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations, 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs E1 1/1 is up. Applique type is Channelized E1 - balanced No alarms detected. alarm-trigger is not set Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line. International Bit: 1, National Bits: 11111 Linestate Debounce is disabled Data in current interval (750 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Total Data (last 52 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations, 0 Slip Secs, 1 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins, 1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs E1 1/2 is administratively down. E1 1/3 is administratively down. E1 1/4 is administratively down. E1 1/5 is administratively down. E1 1/6 is administratively down. E1 1/7 is administratively down. Router#show interfaces serial 1/0:15 Serial1/0:15 is up, line protocol is up (spoofing) Hardware is PA-MC-8TE1 Plus MTU 1500 bytes, BW 64 Kbit/sec, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation HDLC, crc 16, loopback not set Last input 00:00:06, output 00:00:06, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/16 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 48 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 8835 packets input, 35235 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 8830 packets output, 35199 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 unknown protocol drops 0 unknown protocol drops 0 output buffer failures, 0 output buffers swapped out 1 carrier transitions no alarm present Timeslot(s) Used:16, subrate: 64Kb/s, transmit delay is 0 flags Router#show voice port summary IN OUT PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC =============== == ============ ===== ==== ======== ======== == PWR FAILOVER PORT PSTN FAILOVER PORT ================= ================== Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
pashashtepa Posted October 20, 2016 8 port, software configurable Multichannel T1/E1 without TDM Port Adapter смущает without должна же быть и коммутация каналов с атс, первое моё знакомство cisco voip когда цисковед заказал неправильную карточку которая поддерживает только передачу данных то есть гарантированные 2Мб Е1, но без голоса. При это L2 уровень поднимался и я выходил набор в канал на заданную линию из своей АТС звонки никуда не маршрутизировались. а на нормальной появились голосовые параметры после обозначения контроллера как Е1 и после ребута маршрутизатора Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
sol Posted October 20, 2016 Просто дружеский совет. Для вашей задачи возьмите младшую платформу типа 2811. С нужным кол-вом DSP и нужным модулем Е1. Так будет проще. 7200 - это старшая модель и с голосом там всё, хм, сложно. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
DanilKT Posted October 21, 2016 sol На свой вопрос ответ я, кажется, нашел, по наводке pashashtepa https://supportforums.cisco.com/discussion/10024786/pa-mc-8te1-vs-pa-mcx-8te1 Спасибо! просто была 7206 с этим модулем, подумал, что ее можно использовать. Есть еще AS5350, буду ее ковырять. Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...
catalist Posted October 23, 2016 (edited) NAME: "module 1", DESCR: "8 port, software configurable Multichannel T1/E1 without TDM Port Adapter" PID: PA-MC-8TE1+ , VID: , SN: JAE09044MKR Edited October 23, 2016 by catalist Вставить ник Quote Ответить с цитированием Share this post Link to post Share on other sites More sharing options...