Jump to content
Калькуляторы

Nexus сошел с ума

Reply to this topic

ivanm38   

ivanm38
Posted

Всем привет

внезапно, по неизвестной причине cisco отказалась принимать модули сфп

до этого проработала длительное время

конфигурация не менялась

модуля не менялись

 

в логах вот такое

 

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/1 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/9 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/10 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/11 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/12 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/13 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/14 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/15 is not supported
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/16 is not supported

 

линк не поднимает соответсвенно

что ей надо? как лечить?

и второй вопрос, может обновить ее? не поделитесь прошивкой свежей?

у меня

 

Software
 BIOS:      version 1.5.0
 loader:    version N/A
 kickstart: version 5.1(3)N1(1)
 system:    version 5.1(3)N1(1)
 power-seq: Module 1: version v1.2
 BIOS compile time:       11/30/10
 kickstart image file is: bootflash:///n5000-uk9-kickstart.5.1.3.N1.1.bin
 kickstart compile time:  12/6/2011 22:00:00 [12/07/2011 09:08:01]
 system image file is:    bootflash:///n5000-uk9.5.1.3.N1.1.bin
 system compile time:     12/6/2011 22:00:00 [12/07/2011 10:47:44]


Hardware
 cisco Nexus5010 Chassis ("20x10GE/Supervisor")
 Intel(R) Celeron(R) M CPU    with 2065536 kB of memory.


 Device name:
 bootflash:    1003520 kB

Kernel uptime is 0 day(s), 0 hour(s), 8 minute(s), 22 second(s)

Last reset at 336681 usecs after  Wed May  4 14:12:46 2016

 Reason: Reset Requested by CLI command reload
 System version: 5.1(3)N1(1)
 Service: 

plugin
 Core Plugin, Ethernet Plugin

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

нет

 

sh interface ethernet 1/13 transceiver calibrations 
Ethernet1/13
   transceiver is present
   type is 10Gbase-SR
   name is Arista Networks 
   part number is SFP-10G-SR      
   revision is 0002
   serial number is XCW1227FD0K3    
   nominal bitrate is 10300 MBit/sec
   Link length supported for 50/125um OM2 fiber is 82 m
   Link length supported for 50/125um OM3 fiber is 300 m
   cisco id is --
   cisco extended id number is 4


               SFP Internal Calibrations Information
   ----------------------------------------------------------------------
               Slope  Offset      Rx4/Rx3/Rx2/Rx1/Rx0
   ----------------------------------------------------------------------
   Temperature     0      0
   Voltage         0      0
   Current         0      0
   Tx Power        0      0
   Rx Power                       0.0000/0.0000/0.0000/0.0000/0.0000
   ----------------------------------------------------------------------

Share this post

Link to post
Share on other sites

Dimka88   

Dimka88
Posted

В логах кроме

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/1 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/9 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/10 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/11 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/12 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/13 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/14 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/15 is not supported

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/16 is not supported

что то еще было?

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

еще вот это постоянно сыпет в логи

 

%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/1 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/1 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/9 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/9 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/10 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/10 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/11 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/11 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/12 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/12 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/13 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/13 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/14 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/14 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/15 is not supported
%ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/15 is down (None)
%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/16 is not supported

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted 

sh interface ethernet 1/1 transceiver calibrations

Покажите, может там проблема. Все SFP 10g?

 

нет, половина гигабитных модулей

 

sh interface ethernet 1/1 transceiver calibrations 
Ethernet1/1
   transceiver is present
   type is SFP-1000BASE-LX
   name is OEM             
   part number is SFP-WDM1.25G-31 
   revision is 1.0 
   serial number is PD78303376      
   nominal bitrate is 1300 MBit/sec
   Link length supported for 9/125um fiber is 3 km
   cisco id is --
   cisco extended id number is 4

SFP calibration is invalid

Share this post

Link to post
Share on other sites

Dimka88   

Dimka88
Posted (edited)

Скорость принудительно выставлена, там где модуля 1G? Что то подобное когда то встречал.

Edited by Dimka88

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

Скорость принудительно выставлена, там где модуля 1G? Что то подобное когда то встречал.

 

да

 

interface Ethernet1/1
 description UP_MedConv
 no cdp enable
 switchport access vlan 10
 spanning-tree bpduguard disable
 spanning-tree bpdufilter enable
 speed 1000

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

 

 

noname# sh int eth 1/1 status

--------------------------------------------------------------------------------
Port          Name               Status    Vlan      Duplex  Speed   Type
--------------------------------------------------------------------------------
Eth1/1        UP_MedConv         connected 10        full    1000    SFP-1000BAS
noname# sh int eth 1/1
Ethernet1/1 is up
 Hardware: 1000/10000 Ethernet, address: 0005.9b27.4188 (bia 0005.9b27.4188)
 Description: UP_MedConv
 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
 reliability 255/255, txload 1/255, rxload 1/255
 Encapsulation ARPA
 Port mode is access
 full-duplex, 1000 Mb/s, media type is 10G
 Beacon is turned off
 Input flow-control is off, output flow-control is off
 Rate mode is dedicated
 Switchport monitor is off 
 EtherType is 0x8100 
 Last link flapped 00:43:56
 Last clearing of "show interface" counters 01:09:17
 30 seconds input rate 363848 bits/sec, 291 packets/sec
 30 seconds output rate 227000 bits/sec, 24 packets/sec
 Load-Interval #2: 5 minute (300 seconds)
   input rate 325.48 Kbps, 211 pps; output rate 106.09 Kbps, 7 pps
 RX
   185578 unicast packets  143148 multicast packets  255201 broadcast packets
   583927 input packets  87108756 bytes
   0 jumbo packets  0 storm suppression packets
   0 runts  0 giants  0 CRC  0 no buffer
   0 input error  0 short frame  0 overrun   0 underrun  0 ignored
   0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
   0 input with dribble  0 input discard
   0 Rx pause
 TX
   35012 unicast packets  95 multicast packets  8 broadcast packets
   35115 output packets  26369270 bytes
   0 jumbo packets
   0 output errors  0 collision  0 deferred  0 late collision
   0 lost carrier  0 no carrier  0 babble 0 output discard
   0 Tx pause
 1 interface resets

noname# conf
Enter configuration commands, one per line.  End with CNTL/Z.
noname(config)# int eth 1/1
noname(config-if)# shu
noname(config-if)# no shu
noname(config-if)# sh int eth 1/1 status

--------------------------------------------------------------------------------
Port          Name               Status    Vlan      Duplex  Speed   Type
--------------------------------------------------------------------------------
Eth1/1        UP_MedConv         connected 10        full    1000    SFP-1000BAS
noname(config-if)# sh int eth 1/1
Ethernet1/1 is up
 Hardware: 1000/10000 Ethernet, address: 0005.9b27.4188 (bia 0005.9b27.4188)
 Description: UP_MedConv
 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
 reliability 255/255, txload 1/255, rxload 1/255
 Encapsulation ARPA
 Port mode is access
 full-duplex, 1000 Mb/s, media type is 10G
 Beacon is turned off
 Input flow-control is off, output flow-control is off
 Rate mode is dedicated
 Switchport monitor is off 
 EtherType is 0x8100 
 Last link flapped 00:00:11
 Last clearing of "show interface" counters 01:09:54
 30 seconds input rate 164248 bits/sec, 176 packets/sec
 30 seconds output rate 6088 bits/sec, 4 packets/sec
 Load-Interval #2: 5 minute (300 seconds)
   input rate 297.18 Kbps, 200 pps; output rate 85.14 Kbps, 14 pps
 RX
   188130 unicast packets  145086 multicast packets  258715 broadcast packets
   591931 input packets  88079084 bytes
   0 jumbo packets  0 storm suppression packets
   0 runts  0 giants  0 CRC  0 no buffer
   0 input error  0 short frame  0 overrun   0 underrun  0 ignored
   0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
   0 input with dribble  0 input discard
   0 Rx pause
 TX
   35193 unicast packets  104 multicast packets  8 broadcast packets
   35305 output packets  26403055 bytes
   0 jumbo packets
   0 output errors  0 collision  0 deferred  0 late collision
   0 lost carrier  0 no carrier  0 babble 0 output discard
   0 Tx pause
 2 interface resets

 

и другой порт, 10 гигабитный модуль

 

noname# sh int eth 1/13 sta

--------------------------------------------------------------------------------
Port          Name               Status    Vlan      Duplex  Speed   Type
--------------------------------------------------------------------------------
Eth1/13       Ser2_141           notconnec 20        full    10G     10Gbase-SR 
noname# sh int eth 1/13
Ethernet1/13 is down (Link not connected)
 Hardware: 10000 Ethernet, address: 0005.9b27.4194 (bia 0005.9b27.4194)
 Description: Ser2_141
 MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
 reliability 255/255, txload 1/255, rxload 1/255
 Encapsulation ARPA
 Port mode is access
 full-duplex, 10 Gb/s, media type is 10G
 Beacon is turned off
 Input flow-control is off, output flow-control is off
 Rate mode is dedicated
 Switchport monitor is off 
 EtherType is 0x8100 
 Last link flapped never
 Last clearing of "show interface" counters never
 30 seconds input rate 0 bits/sec, 0 packets/sec
 30 seconds output rate 0 bits/sec, 0 packets/sec
 Load-Interval #2: 5 minute (300 seconds)
   input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
 RX
   0 unicast packets  0 multicast packets  0 broadcast packets
   0 input packets  0 bytes
   0 jumbo packets  0 storm suppression packets
   0 runts  0 giants  0 CRC  0 no buffer
   0 input error  0 short frame  0 overrun   0 underrun  0 ignored
   0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
   0 input with dribble  0 input discard
   0 Rx pause
 TX
   0 unicast packets  0 multicast packets  0 broadcast packets
   0 output packets  0 bytes
   0 jumbo packets
   0 output errors  0 collision  0 deferred  0 late collision
   0 lost carrier  0 no carrier  0 babble 0 output discard
   0 Tx pause
 0 interface resets

noname# conf 
Enter configuration commands, one per line.  End with CNTL/Z.
noname(config)# int eth 1/13
noname(config-if)# shu
noname(config-if)# no shu
noname(config-if)# sh int eth 1/13 sta

--------------------------------------------------------------------------------
Port          Name               Status    Vlan      Duplex  Speed   Type
--------------------------------------------------------------------------------
Eth1/13       Ser2_141           notconnec 20        full    10G     10Gbase-SR 
noname(config-if)# sh int eth 1/13
Ethernet1/13 is down (Link not connected)
 Hardware: 10000 Ethernet, address: 0005.9b27.4194 (bia 0005.9b27.4194)
 Description: Ser2_141
 MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec
 reliability 255/255, txload 1/255, rxload 1/255
 Encapsulation ARPA
 Port mode is access
 full-duplex, 10 Gb/s, media type is 10G
 Beacon is turned off
 Input flow-control is off, output flow-control is off
 Rate mode is dedicated
 Switchport monitor is off 
 EtherType is 0x8100 
 Last link flapped never
 Last clearing of "show interface" counters never
 30 seconds input rate 0 bits/sec, 0 packets/sec
 30 seconds output rate 0 bits/sec, 0 packets/sec
 Load-Interval #2: 5 minute (300 seconds)
   input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
 RX
   0 unicast packets  0 multicast packets  0 broadcast packets
   0 input packets  0 bytes
   0 jumbo packets  0 storm suppression packets
   0 runts  0 giants  0 CRC  0 no buffer
   0 input error  0 short frame  0 overrun   0 underrun  0 ignored
   0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
   0 input with dribble  0 input discard
   0 Rx pause
 TX
   0 unicast packets  0 multicast packets  0 broadcast packets
   0 output packets  0 bytes
   0 jumbo packets
   0 output errors  0 collision  0 deferred  0 late collision
   0 lost carrier  0 no carrier  0 babble 0 output discard
   0 Tx pause
 0 interface resets

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

да, на 13, 14, 15 ,16 тоже должны быть

а их нет

 

патчи и модуля меняли

да и не могли сразу куча модулей сгореть одновременно

Share this post

Link to post
Share on other sites

vurd   

vurd
Posted

В первом порту линк всё-таки поднялся?

 

>%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/1 is not supported

 

>noname(config-if)# sh int eth 1/1

>Ethernet1/1 is up

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

В первом порту линк всё-таки поднялся?

 

>%ETHPORT-3-IF_UNSUPPORTED_TRANSCEIVER: Transceiver on interface Ethernet1/1 is not supported

 

>noname(config-if)# sh int eth 1/1

>Ethernet1/1 is up

 

да, в первом поднят линк

Share this post

Link to post
Share on other sites

vurd   

vurd
Posted

Ну? И что вы для этого сделали?

У вас же в первом тоже была такая же ситуация, что и с остальными. Ансапортед трансивер, все дела.

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

Ансапортед трансивер, все дела.

 

это я делал еще до создания темы

просто сам поднялся

 

как посмотреть что то типа дебаг лога?

Share this post

Link to post
Share on other sites

ivanm38   

ivanm38
Posted

А уровень сигнала проверчяли?

Попробуйте между двумя 10G портами петлю сделать. Линк поднимется?

 

запетляли 13 и 14 порт, в логах вот такое

 

2016 May  4 16:45:26 noname %ETHPORT-5-SPEED: Interface Ethernet1/13, operational speed changed to 10 Gbps
2016 May  4 16:45:26 noname %ETHPORT-5-IF_DUPLEX: Interface Ethernet1/13, operational duplex mode changed to Full
2016 May  4 16:45:26 noname %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet1/13, operational Receive Flow Control state changed to off
2016 May  4 16:45:26 noname %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet1/13, operational Transmit Flow Control state changed to off
2016 May  4 16:45:26 noname %ETHPORT-5-SPEED: Interface Ethernet1/14, operational speed changed to 10 Gbps
2016 May  4 16:45:26 noname %ETHPORT-5-IF_DUPLEX: Interface Ethernet1/14, operational duplex mode changed to Full
2016 May  4 16:45:26 noname %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet1/14, operational Receive Flow Control state changed to off
2016 May  4 16:45:26 noname %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet1/14, operational Transmit Flow Control state changed to off
2016 May  4 16:45:26 noname %ETHPORT-5-IF_UP: Interface Ethernet1/13 is up in mode access
2016 May  4 16:45:26 noname %ETHPORT-5-IF_UP: Interface Ethernet1/14 is up in mode access

 

получается дело не в кошке? и не модулях на ее стороне?

Share this post

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
Followers 0
Go to topic listing Активное оборудование Ethernet, IP, MPLS, SDN/NFV...