roma_good Posted December 12, 2016 · Report post как можна включить compliance test Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post скачиваете конфиг radio.countrycode=511 radio.1.countrycode=511 заливаете конфиг обратно Share this post Link to post Share on other sites
roma_good Posted December 12, 2016 · Report post не работает Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post уточнение - речь про 5AC если надо на M2/M5, то нужно зайти на устройство по ssh и дать команду enable_ct Share this post Link to post Share on other sites
roma_good Posted December 12, 2016 · Report post R5AC-PTMP Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post тогда должно работать. проверено на 7.2.4 и 8-RC3 каковы симптомы не-работы? Share this post Link to post Share on other sites
roma_good Posted December 12, 2016 · Report post сперва enable_ct а потом менять конфигурацию /tmp/system.cfg ???? Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post На M2/M5 - надо выполнить команду enable_ct После этого откроется список стран, и можно будет выбрать CT без правки конфиг-файла. На 5AC - команды не нужны. Конфиг можно слить через веб, отредактировать и залить обратно, тоже через веб. Share this post Link to post Share on other sites
roma_good Posted December 12, 2016 (edited) · Report post radio.1.atpc.threshold=30 radio.1.atpc.maxpower=0 radio.1.atpc.minpower=0 radio.1.atpc.status=disabled radio.1.ampdu.status=enabled radio.1.ampdu.frames=32 radio.1.cmsbias=0 radio.1.scan_list.status=disabled radio.1.polling_11ac_hybrid=0 radio.1.polling_11ac_11n_compat=0 radio.1.center.1.freq=5310 radio.1.freq=5300 radio.1.cable.loss=2 radio.1.antenna.id=1 radio.1.antenna.gain=10 radio.1.txpower=22 radio.1.subsystemid=0xe3f5 radio.1.status=enabled radio.1.reg_obey=enabled radio.1.ptpmode=0 radio.1.pollingpri=2 radio.1.pollingnoack=0 radio.1.polling=enabled radio.1.obey=enabled radio.1.mode=master radio.1.low_txpower_mode=disabled radio.1.ieee_mode=11acvht40 radio.1.dfs.status=enabled radio.1.devname=ath0 radio.1.cwm.mode=1 radio.1.cwm.enable=0 radio.1.countrycode=511 radio.1.chanbw=40 radio.1.acktimeout=25 radio.1.ackdistance=643 radio.1.ack.auto=enabled radio.status=enabled radio.countrycode=511 Edited December 12, 2016 by roma_good Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post а список частот как выглядит? Share this post Link to post Share on other sites
roma_good Posted December 12, 2016 (edited) · Report post Edited December 12, 2016 by roma_good Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post Тогда временно залейте CT прошивку http://www.ubnt.com/downloads/11AC-fw-internal/v7.2/XC.v7.2-licensed.30663.160331.1729.bin выберите страну Licensed, и верните восьмую обратно. но для выбора страны потребуется сброс в заводские настройки Share this post Link to post Share on other sites
roma_good Posted December 12, 2016 · Report post сменил прошивку Share this post Link to post Share on other sites
rdc Posted December 12, 2016 · Report post Уточнение - похоже, это аппаратное ограничение самой модели. https://community.ubnt.com/t5/airMAX-AC/Differance-between-Rocket5-AC-Prism-and-Rocket-ac-PTMP/m-p/1490889#M12309 Share this post Link to post Share on other sites
Sonne Posted December 13, 2016 · Report post Rocket AC light или Prism? Share this post Link to post Share on other sites
Audito Posted December 16, 2016 · Report post Добрый вечер. Никто ничего не путает по поводу кантри кода 511? По моему в АС 5000 надо прописать в конфиге в 2х или 3х местах. делал с полгода назад, все заработало. Share this post Link to post Share on other sites
rdc Posted December 16, 2016 · Report post Фирменная CT прошивка ставит именно 511 код. 5000 тоже работает, но на нём недоступно 80мгц для ptp Share this post Link to post Share on other sites
rdc Posted December 18, 2016 · Report post 6.0-RC3 http://www.ubnt.com/downloads/XN-fw-internal/v6.0/XM.v6.0-RC3-cs.30084.161216.1534.bin http://www.ubnt.com/downloads/XN-fw-internal/v6.0/XW.v6.0-RC3-cs.30084.161216.1518.bin Share this post Link to post Share on other sites
Engineer09 Posted December 20, 2016 · Report post Вышли официальные 6.0 и 8.0, обновляются из вебморды, но разницы с RC3 пока не заметил. Share this post Link to post Share on other sites
Sonne Posted December 24, 2016 · Report post Может новую тему откроем? А то эиа своим названием в заблуждение вводит. Share this post Link to post Share on other sites
pingz Posted December 27, 2016 · Report post Производительность повысилась? Share this post Link to post Share on other sites
rdc Posted December 28, 2016 · Report post между 5 и 6 разницы в производительности нет. между 7 и 8 - может быть, т.к. протокол изменили Share this post Link to post Share on other sites
streeter Posted January 4, 2017 · Report post rdc, вчера сменил на одном из мостов AirOS 7.2.4 на 8. Погонял за ночь. Кроме более стабильной работы Airview и новой фичи AirMagic существенных отличий не нашел. WebUI не в счет. Share this post Link to post Share on other sites
vasily Posted January 4, 2017 · Report post rdc, вчера сменил на одном из мостов AirOS 7.2.4 на 8. Погонял за ночь. Кроме более стабильной работы Airview и новой фичи AirMagic существенных отличий не нашел. WebUI не в счет. Вы не могли бы подробнее описать, что за новая фича AirMagic для чего она и как нею пользоваться. Share this post Link to post Share on other sites