Rch Posted May 27, 2015 · Report post Всем доброго времени суток , потребовалось настроить LACP на Alcatel OmniSwitch 6850E , настроивал по мануалу. создаю linkagg lacp linkagg 1 size 2 admin state enable lacp linkagg 1 actor admin key 5 show linkagg Number Aggregate SNMP Id Size Admin State Oper State Att/Sel Ports -------+----------+---------+----+------------+--------------+------------- 1 Dynamic 40000001 2 ENABLED DOWN 0 0 После добавляю порт в группу lacp agg 1/21 actor admin key 5 Смотрим linkagg show linkagg Number Aggregate SNMP Id Size Admin State Oper State Att/Sel Ports -------+----------+---------+----+------------+--------------+------------- 1 Dynamic 40000001 2 ENABLED DOWN 0 0 И по какой то причине не ведемой для меня причине кол-во Sel port отсталось все так же 0 , может кто сталкивался с такой проблемой , буду рад любым мыслям и высказывания. Share this post Link to post Share on other sites
zvukovik Posted May 27, 2015 (edited) · Report post А статический linkagg заводится? Или у Вас разнородное оборудование. Edited May 27, 2015 by zvukovik Share this post Link to post Share on other sites
Rch Posted May 28, 2015 · Report post Разное оборудование. Share this post Link to post Share on other sites
dmvy Posted May 29, 2015 · Report post Должно работать. Покажите расширенную информацию. Если на противоположной стороне dlink, то возможно по-умолчанию lacp passive на нем. -> show configuration snapshot linkagg ! Link Aggregate : lacp linkagg 2 size 4 admin state enable lacp linkagg 2 name "sw-web" lacp linkagg 2 actor admin key 2 lacp linkagg 5 size 4 admin state enable lacp linkagg 5 name "sw2-vost92" lacp linkagg 5 actor admin key 5 lacp agg 1/9 actor admin key 2 lacp agg 1/10 actor admin key 2 lacp agg 1/11 actor admin key 5 lacp agg 1/12 actor admin key 5 -> show linkagg Number Aggregate SNMP Id Size Admin State Oper State Att/Sel Ports -------+----------+---------+----+------------+--------------+------------- 2 Dynamic 40000002 4 ENABLED UP 2 2 5 Dynamic 40000005 4 ENABLED UP 2 2 -> show linkagg 2 Dynamic Aggregate SNMP Id : 40000002, Aggregate Number : 2, SNMP Descriptor : Dynamic Aggregate Number 2 ref 40000002 size 4, Name : sw-web, Admin State : ENABLED, Operational State : UP, Aggregate Size : 4, Number of Selected Ports : 2, Number of Reserved Ports : 2, Number of Attached Ports : 2, Primary Port : 1/9 LACP MACAddress : [00:e0:b1:a5:40:9e], Actor System Id : [00:00:00:00:00:00], Actor System Priority : 0, Actor Admin Key : 2, Actor Oper Key : 2, Partner System Id : [00:00:00:00:00:00], Partner System Priority : 0, Partner Admin Key : 0, Partner Oper Key : 48 Share this post Link to post Share on other sites
Rch Posted May 29, 2015 · Report post С обратной стороны Cisco 3560G ! Link Aggregate : lacp linkagg 1 size 2 admin state enable lacp linkagg 1 actor admin key 5 lacp agg 1/21 actor admin key 5 lacp agg 1/23 actor admin key 5 show linkagg Number Aggregate SNMP Id Size Admin State Oper State Att/Sel Ports -------+----------+---------+----+------------+--------------+------------- 1 Dynamic 40000001 2 ENABLED DOWN 0 0 show linkagg 1 Dynamic Aggregate SNMP Id : 40000001, Aggregate Number : 1, SNMP Descriptor : Dynamic Aggregate Number 1 ref 40000001 size 2, Name : , Admin State : ENABLED, Operational State : DOWN, Aggregate Size : 2, Number of Selected Ports : 0, Number of Reserved Ports : 0, Number of Attached Ports : 0, Primary Port : NONE LACP MACAddress : [00:00:00:00:00:00], Actor System Id : [00:00:00:00:00:00], Actor System Priority : 0, Actor Admin Key : 5, Actor Oper Key : 0, Partner System Id : [00:00:00:00:00:00], Partner System Priority : 0, Partner Admin Key : 0, Partner Oper Key : 0, Pre-emption : DISABLED, Pre-empt Value : 30 Share this post Link to post Share on other sites
dmvy Posted May 29, 2015 · Report post а порты такие есть? Их состояние. show interfaces port софт какой? -> show system System: Description: 6.3.4.378.R01 GA, March 11, 2009., Object ID: 1.3.6.1.4.1.6486.800.1.1.2.1.7.1.10, Up Time: 226 days 19 hours 18 minutes and 58 seconds, Еще для удобства номер linkagg и admin key делаем одинаковый Share this post Link to post Share on other sites
Rch Posted June 2, 2015 · Report post show interfaces port 1/21 disable down none "link_agg_1/1" 1/23 disable down none "link_agg_1/2" -> show system System: Description: 6.3.4.621.R01 Service Release, July 26, 2010., Object ID: 1.3.6.1.4.1.6486.800.1.1.2.1.7.1.10, Up Time: 220 days 21 hours 1 minutes and 24 seconds, Порты в состояние disable , требуется их включить? И после включения они подтянутся в группу агригации? До этого когда делал статическую агрегацию значение Seleсted Ports менялось даже при отключенных интерфесах. Share this post Link to post Share on other sites
dmvy Posted June 2, 2015 · Report post все правильно, не поднимутся порты, так и будет отбражаться. Share this post Link to post Share on other sites
