да, всё так и сделал
MainRouter#sh lacp 1 c
LACPDUs Marker Marker Response LACPDUs
Port Sent Recv Sent Recv Sent Recv Pkts Err
---------------------------------------------------------------------
Channel group: 1
Gi0/0/0 47979 1488 0 0 0 0 0
Gi0/0/3 47951 1484 0 0 0 0 0
MainRouter#sh lacp 1 internal
Flags: S - Device is requesting Slow LACPDUs
F - Device is requesting Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode
Channel group 1
LACP port Admin Oper Port Port
Port Flags State Priority Key Key Number State
Gi0/0/0 SA bndl 32768 0x1 0x1 0x1 0x3D
Gi0/0/3 SA bndl 32768 0x1 0x1 0x4 0x3D
MainRouter#sh lacp 1 n
Flags: S - Device is requesting Slow LACPDUs
F - Device is requesting Fast LACPDUs
A - Device is in Active mode P - Device is in Passive mode
Channel group 1 neighbors
Partner's information:
Partner Partner LACP Partner Partner Partner Partner Partner
Port Flags State Port Priority Admin Key Oper Key Port Number Port State
Gi0/0/0 FA bndl 1 0x0 0x11 0x11 0x3F
Gi0/0/3 FA bndl 1 0x0 0x11 0x12 0x3F
MainRouter#
Но успех был не долог(
Трафик частично пошёл в 18 порт, но только исходящий, входящий не хочет
я тоже думал про это, но при выполнении этой команды выходи
MainRouter#conf t
Enter configuration commands, one per line. End with CNTL/Z.
MainRouter(config)#in
MainRouter(config)#int
MainRouter(config)#interface gi
MainRouter(config)#interface gigabitEthernet 0/0/0
MainRouter(config-if)#channel-group 1 mode active
Interface already configured in Port-Channel-1.
MainRouter(config-if)#interface gigabitEthernet 0/0/3
MainRouter(config-if)#channel-group 1 mode active
Interface already configured in Port-Channel-1.
а команда
MainRouter#sh lacp 1 neighbor
No interfaces configured in the channel group
MainRouter#show etherchannel summary
Flags: D - down P/bndl - bundled in port-channel
I - stand-alone s/susp - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
Number of channel-groups in use: 1
Number of aggregators: 1
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
1 Po1(RU) Gi0/0/0(P) Gi0/0/3(P)
RU - L3 port-channel UP State
SU - L2 port-channel UP state
P/bndl - Bundled
S/susp - Suspended
DGS-3627G:admin#show link_aggregation
Command: show link_aggregation
Link Aggregation Algorithm = MAC-Source
Group ID : 1
Type : LACP
Master Port : 17
Member Port : 17-18
Active Port : 17
Status : Enabled
Flooding Port : 17
Total Entries : 1
MainRouter#sh etherchannel load-balancing
EtherChannel Load-Balancing Method:
Global LB Method: vlan-manual
LB Algo type: Destination MAC
Port-Channel: LB Method
Port-channel1 : vlan-manual (Destination MAC)
Всё по прежнему( , всё льёт в 17 порт
Да, линк поднялся, пакеты пошли, но сразу не проверил, что идут они все только в 17 порт.
Добавил: port-channel load-balance-hash-algo src-mac
результатов не принесло, что упускаю?
Здравствуйте, вчера Asr1002 четыре раза за день выходил из строя. Первый раз даже IOS был стёрт, в Rommon попал, было грустно. В последующие только конфиг теряли.