Здравствуйте!
1. Есть вот такое замечательное "железо" c ОС, - CISCO-like; )
SNR-S2985G-48T Device, Compiled on Aug 17 17:35:17 2015
SoftWare Version 7.0.3.5(R0241.0055)
BootRom Version 7.2.22
HardWare Version 1.0.1
SNR-S2985G-8T Device, Compiled on Jan 23 14:49:06 2017
SoftWare Version 7.0.3.5(R0241.0137)
BootRom Version 7.2.21
HardWare Version 1.1.2
Подскажите, у этой серии есть поддержка OSPF ?
Чтобы было возможным, например, вот так:
config terminal
interface loopback 1
ip address 10.10.10.2 255.255.255.255
router ospf 1
ospf router-id 10.10.10.2
network 10.10.10.2 0.0.0.0 area 0
network 172.16.1.0 0.0.0.3 area 0
network 10.100.100.0 0.0.0.255 area 0
passive-interface Loopback1
Аггрегация у этих двух, на LACP - штатно,
а вот Распределение, на чём строить?
Если, присутствует только статическая маршрутизация?
Хотя, динамическая, судя по выводу комманды, #show ip route , всё же должна быть.
Или это для другой линейки серии 29хх - ?
#show ip route
Codes: K - kernel, C - connected, S - static, R - RIP, B - BGP
O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default
Если, - ДА (ЕСТЬ поддержка OSPF), тогда подскажите где и как включить?
Не нашёл в режиме конфигурации, ничего подходящего, кроме команды ip route, по этому вопросу:
(config)#ip route ?
A.B.C.D IP destination prefix
A.B.C.D/M IP destination prefix (e.g. 10.0.0.0/8)
Может, как всегда, - чёрной кошки в тёмной комнате, просто нет?
Configure commands:
show Show running system information
aaa Configure AAA(Authentication, Authorization and pre-Accounting)
aaa-accounting Accounting configurations
access-list Add an access list entry
accounting Accounting configuration commands
am Configure AM
anti-arpscan Anti-arpscan
arp Arp
authentication Authentication configuration commands
authorization Authorization configuration commands
banner Define a login banner
bpdu-tunnel-protocol Bpdu-tunnel
captive-portal Enter captive portal mode.
class-map Configure QoS Class Map
clear Reset functions
clock Set clock
cluster Cluster configuration commands
cpu-rx-ratelimit CPU received traffic rate limit
delete delete
dosattack-check Dosattack
dot1x Configure 802.1X
dynamic-vlan Configure dynamic vlan
enable Modify enable password parameters
end End current mode and change to EXEC mode
erps-ring Ethernet ring running G.8032
errp errp
ethernet Ethernet
exec-timeout Set timeout value
exit End current mode and down to previous mode
firewall Configure firewall status
flowctrl-special set flowctrl
ftp-server FTP Server config
fulleaps FULL Ethernet Automatic Protection Switching
garp Set GARP parameter
gvrp Set GVRP parameter
hardware-address-list Permit DHCP adding option 66 or 150 or 14x to the client in the hardware-address-list
help Description of the interactive help system
history Set history related parameters
hostname Modify hostname
interface Select an interface to configure
ip IP information
ipv6 IPv6 information
isolate-port Isolate-port information
key Authentication key management
l2-address-table L2 address table setting
l3-station-move Configure l3-station-move
lacp Lacp configuration
lldp Link Layer Discovery Protocol
load load
load-balance Load balancing method
logging Logging
login Enable password checking
loopback-detection Loopback-detection
mac-access-list Global MAC configuration subcommands_Named access-list
mac-address Mac address config
mac-address-learning Mac address-learning config
mac-address-table MAC address table setting
mac-authentication-bypass Configure MAC authentication bypass feature
mac-ip-access-list Global MAC-IP configuration subcommands_Named access-list
mac-vlan Configure mac vlan
mls Configure MultiLayer Switching characteristics
monitor Configure SPAN monitoring
mrpp Multi-layer Ring Protection Protocol
mtu Maximum Transmission Unit
multi Multi users
multi-recursive-routes Multiple recursive routes
multicast Multicast config
multicast-forwarding multicast-forwarding configure
multicast-vlan Configure multicast vlan
neighboure neighboure system
no Negate a command or set its defaults
ntp Network time protocol
ntp-service ntp-service
password Assign the terminal connection password
policy Policy
policy-map Configure QoS Policy Map
port-group Port-group configuration
port-led port led
port-rate-statistics port-rate-statistics
port-redirect Port-redirect
port-scan-mode Port-scan-mode
pppoe PPPOE intermediate Agent
privilege Set user privilege level
profile-id Add an profile list entry
protocol-vlan Configure protocol vlan
radius Configure RADIUS
radius-server Configure RADIUS server
rmon Config rmon
rps-power rps-power
savi Source Address Validation Improvements
service Modify use of network based services
service-policy Configure QoS Service Policy
set Set
sflow Sflow Global Configuration
show Show running system information
snmp-server Modify SNMP parameters
sntp Simple Network Time protocol
spanning-tree Spanning-tree config
ssh-server Ssh service config command
storm-control Storm-control
subnet-vlan Configure Subnet vlan
sysContact sysContact
sysLocation SysLocation
tacacs-server Config tacacs+ server
telnet-server Telnet server
tftp-server TFTP Server config
time-range Configure a time range
transceiver-monitoring Transceiver monitoring
uldp ULDP information
ulpp Uplink Protection Protocol
ulsm Uplink State Monitor
userdefined-access-list Specify userdefined access list
username Establish User Name Authentication
userpassword Specifies the password for the user
vacl Configure Vlan Acl
vlan Vlan Commands
vlan-port-redirect vlan-port-redirect
vlan-trunk-range vlan-trunk-range
voice-vlan Configure voice vlan
web Config web
web-auth Web set authentication privilege
2. Для обновления обеих драгоценых единиц, до актуальной версии ПО, я могу использовать вот это (универсальное для всей линейки S2985G?):
http://data.nag.ru/SNR Switches/Firmware/SNR-S2985G/recommended/SNR-S2985G-48T(24T_8T)(POE)(UPS)(RPS)_7.0.3.5(R0241.0298).zip
C Уважением,
...
P. S.
Мне думается, что обе модели заявленые производителем, как L2, совсем даже не L2+, поэтому надеяться особо не на что.
Было бы не плохо если бы в линейке S29xx, появился бы так же 8-ми портовый коммутатор L2+, хотя бы.
Чаще других требуются - 8-ми, 16-ти, 24-х портовые с поддержкой L2+, L3, за приемлемые средства. Спрос рождает предложение.
С Уважением,