FenX

rs-232 здесь "полноценный"? не могу заставить работать DS9097U-009# на нем.

Спасибо огромное, всем ответившим!

Помогите опознать разъемы (где купить?)

Спасибо, эта версия и установлена на устройстве. скажите "настоящие" имя данного устройства (можно в личку)

Спасибо, возможно все же узнать имя оригинальной модели или получить обе версии последних прошивок для устройства (от SNR и Dahua)?

подскажите, есть аналог у Dahua со свежей прошивкой?

ищу SCCP прошивку 7940 в русской локалью

присоединяюсь к вопрошающему.

Оружие третьего поколения в Глубине:)

Hi All! Помогите с простой агрегацией портов Centos 6.5 настраивал согласно http://www.alsigned.ru/?p=2896 когда создаю на коммутаторе port-group 1 и добавляю в нее интерфейсы пинг до centos пропадает # cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2+3 (2) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 5 Number of ports: 1 Actor Key: 17 Partner Key: 1 Partner Mac Address: 00:00:00:00:00:00 Slave Interface: eth0 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 3 Permanent HW addr: a4:ba:db:11:18:7f Aggregator ID: 5 Slave queue ID: 0 Slave Interface: eth1 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 3 Permanent HW addr: a4:ba:db:11:18:81 Aggregator ID: 6 Slave queue ID: 0 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 3 Permanent HW addr: a4:ba:db:11:18:83 Aggregator ID: 7 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 3 Permanent HW addr: a4:ba:db:11:18:85 Aggregator ID: 8 Slave queue ID: 0 мак партнерского устройства тоже не обновляется

Вот, сегодня в 4 ночи сам перезапустился загрузка заканчивается на этом: Flowmask is MODIFIED to interface and full flow *Oct 12 05:07:07.776: RP: Currently running ROMMON from S (Gold) region *Oct 12 12:07:14.784 Novosib: %SYS-6-CLOCKUPDATE: System clock has been updated from 05:07:14 UTC Sun Oct 12 2014 to 12:07:14 Novosib Sun Oct 12 2014, configured from console by console. *Oct 12 12:07:15.052 Novosib: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology *Oct 12 12:08:21.952 Novosib: %SYS-5-CONFIG_I: Configured from memory by console *Oct 12 12:08:42.092 Novosib: %SYS-5-RESTART: System restarted -- Cisco IOS Software, s3223_rp Software (s3223_rp-ADVENTERPRISEK9_WAN-VM), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright © 1986-2011 by Cisco Systems, Inc. Compiled Mon 28-Mar-11 05:31 by prod_rel_team *Oct 12 04:53:48.868: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output. *Oct 12 05:07:03.476: %SCHED-SP-7-WATCH: Attempt to set uninitialized watched boolean (address 0). -Process= "<interrupt level>", ipl= -1, pid= -1 : ios-base : (PID=12308, TID=17) : -Traceback=(s3223-adventerprisek9_wan-0-dso-bn.so+0x156A8C) ([26:-3]4-dso-b+0x4F9B48) ([26:-9]2+0x4A0410) ([36:0]+0x49EE90) ([36:0]+0x484304) ([36:0]+0x2FE9BC) ([26:-9]4+0x241F3C) ([36:0]+0x3F7A10) ([0:-3]libc+0x2404C) *Oct 12 05:07:15.049: %SPANTREE-SP-5-EXTENDED_SYSID: Extended SysId enabled for type vlan. The Bridge IDs of all active STP instances have been updated, which might change the spanning tree topology *Oct 12 05:08:41.172: %SYS-SP-5-RESTART: System restarted -- Cisco IOS Software, s3223_sp Software (s3223_sp-ADVENTERPRISEK9_WAN-VM), Version 12.2(33)SXI6, RELEASE SOFTWARE (fc4) Technical Support: http://www.cisco.com/techsupport Copyright © 1986-2011 by Cisco Systems, Inc. Compiled Mon 28-Mar-11 05:50 by prod_rel_team *Oct 12 05:08:41.188: SP: Currently running ROMMON from S (Gold) region *Oct 12 05:08:41.588 UTC: %OIR-SP-6-INSPS: Power supply inserted in slot 1 *Oct 12 12:08:42.160 Novosib: %SSH-5-ENABLED: SSH 2.0 has been enabled *Oct 12 05:08:41.596 UTC: %C6KPWR-SP-4-PSOK: power supply 1 turned on. *Oct 12 05:08:43.524 UTC: %C6KENV-SP-4-FANHIOUTPUT: Version 2 high-output fan-tray is in effect *Oct 12 05:08:43.524 UTC: %OIR-SP-6-INSFAN: Fan 1 inserted *Oct 12 12:08:45.420 Novosib: %SNMP-5-COLDSTART: SNMP agent on host C6509 is undergoing a cold start *Oct 12 12:08:45.510 Novosib: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimal Diagnostics... *Oct 12 12:09:21.732 Novosib: %DIAG-SP-3-MAJOR: Module 5: Online Diagnostics detected a Major Error. Please use 'show diagnostic result <target>' to see test results. *Oct 12 12:09:21.736 Novosib: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestFibDevices failed *Oct 12 12:09:21.736 Novosib: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestIPv4FibShortcut failed *Oct 12 12:09:21.736 Novosib: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestL3Capture2 failed *Oct 12 12:09:21.736 Novosib: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestIPv6FibShortcut failed *Oct 12 12:09:21.736 Novosib: %CONST_DIAG-SP-3-BOOTUP_TEST_FAIL: Module 5: TestMPLSFibShortcut failed *Oct 12 05:09:22.524: %HA_EM-6-LOG: Mandatory.go_bootup.tcl: GOLD EEM TCL policy for boot up diagnostic Crashdump : 05:09:24.708 Sun Oct 12 2014 : ios-base : (PID=12310, TID=7) : -Traceback=(s3223_rp-adventerprisek9_wan-11-dso-b.so+0x417C0C) ([40:0]+0x417C54) ([40:0]+0x456FD4) ([29:-9]7+0x363454) ([39:0]+0x3634D4) ([29:-9]4+0x2BA81C) ([39:0]+0x2BB984) ([39:0]+0x2BB880) ([39:0]+0x2BC89C) ([29:-9]5+0x29EFF8) ([39:0]+0x28D860) ([39:0]+0x28DAF0) ([29:-9]0+0x40E700) ([29:-9]7+0x34F304) ([0:-3]libc+0x2404C) crashdump called (with pause = 0 sec) %ALIGN-1-FATAL: Illegal access to a low address 12:09:24 Novosib Sun Oct 12 2014 addr=0x0, pc=0x75EE1BA4, ra=0x75EE1AD0, sp=0xF59850 SLOT0:00:03:22: %DUMPER-3-PROCINFO: pid = 12310: (sbin/ios-base), terminated due to signal SIGSEGV, Segmentation violation (Address not mapped) SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: zero at v0 v1 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R0 00000000 7C18CB78 00000017 00F59FC0 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: a0 a1 a2 a3 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R4 00000002 00F59EC0 00F59FC0 00000000 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: t0 t1 t2 t3 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R8 00000000 00000000 00000053 00000000 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: t4 t5 t6 t7 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R12 00000000 776AC070 FFFFFFFF 77688000 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: s0 s1 s2 s3 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R16 00F59B10 00F59B40 00000000 0000001F SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: s4 s5 s6 s7 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R20 7A66E0A0 00000000 00000000 08196A48 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: t8 t9 k0 k1 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R24 00F59750 7065D6B0 00000000 00000000 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: gp sp s8 ra SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R28 7C0DF490 00F59850 00000000 75EE1AD0 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: sr lo hi bad SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R32 1001D463 00000000 00000002 00000000 SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: cause pc epc SLOT0:00:03:22: %DUMPER-3-REGISTERS_INFO: 12310: R36 0000000C 75EE1BA4 00000000 SLOT0:00:03:23: %DUMPER-3-TRACE_BACK_INFO: 12310: (s3223_rp-adventerprisek9_wan-14-dso-b.so+0x269BA4) (s3223_rp-adventerprisek9_wan-11-dso-b.so+0x417C0C) (s3223_rp-adventerprisek9_wan-11-dso-b.so+0x417C54) (s3223_rp-adventerprisek9_wan-11-dso-b.so+0x456FD4) (s3223_rp-adventerprisek9_wan-7-dso-b.so+0x363454) (s3223_rp-adventerprisek9_wan-7-dso-b.so+0x3634D4) (s3223_rp-adventerprisek9_wan-4-dso-b.so+0x2BA81C) (s3223_rp-adventerprisek9_wan-4-dso-b.so+0x2BB984) (s3223_rp-adventerprisek9_ SLOT0:00:03:31: %DUMPER-6-BAD_PATH: 12310: Choice 1 either not configured or bad path. Trying next choice. SLOT0:00:03:31: %DUMPER-6-BAD_PATH: 12310: Choice 2 either not configured or bad path. Trying next choice. SLOT0:00:03:31: %DUMPER-6-BAD_PATH: 12310: Choice 3 either not configured or bad path. Trying next choice. SLOT0:00:03:31: %DUMPER-3-DUMP_FAILURE: 12310: Core dump failed: Could not create core SLOT0:00:03:35: %DUMPER-3-CRASHINFO_FILE_NAME: 12310: Crashinfo for process sbin/ios-base at bootflash:/crashinfo_ios-base-20141012-050924 SLOT0:00:03:35: %SYSMGR-3-ABNORMTERM: ios-base:1 (jid 71) abnormally terminated, restart disabled SLOT0:00:03:35: %SYSMGR-6-ERROR_EOK: ios-base:1 (jid 71) mandatory process exited, rebooting System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright © 2004 by cisco Systems, Inc. Cat6k-MSFC2A platform with 524288 Kbytes of main memory System Bootstrap, Version 12.2(18r)SX9, RELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright © 2008 by cisco Systems, Inc. Cat6k-Sup32 platform with 524288 Kbytes of main memory rommon 1 > убрал перезагрузку с помощью #no diagnostic bootup level minimal загрузилась, сеть еле шевелится посоветуйте, новый SUP будет еще дней 5 ехать

Очень прошу помочь рабочими конфигами для звонков со * на fxo c выбором определенной линии.

Прикольно ))) Никто не юзает google ... https://www.google.com/webhp?sourceid=chrome-instant&ion=1&ie=UTF-8#hl=ru&sclient=psy-ab&q=allied+telesis+%D1%81%D0%B5%D1%80%D1%82%D0%B8%D1%84%D0%B8%D0%BA%D0%B0%D1%82%D1%8B&oq=allied+telesis+%D1%81%D0%B5%D1%80%D1%82%D0%B8%D1%84%D0%B8%D0%BA%D0%B0%D1%82%D1%8B&gs_l=serp.3...25301.28977.0.29892.12.12.0.0.0.0.62.583.12.12.0...0.0...1c.1.12.psy-ab.Qi8r0Bp2_Tg&pbx=1&bav=on.2,or.r_qf.&fp=eb14fb3c2436b4b2&biw=1920&bih=1113&ion=1 Искомое - http://www.soft-tronik.ru/docs/bpwebsite3.asp?Url=/docs/sert.asp?assortment=3 Там РОСС сертификаты , а инспектору надо было ССС. Нашел уже ССС через тех поддержку телесиса. Можно в личку ссылку? Спасибо.

Спасибо, за ответы!

Без аналога КТВ, возвратные потери не важны?